TSI Instruments DustTrak 8520 Installation and operating instructions
SERIAL DATA ACQUISITION
WITH THE TSI®DUSTTRAK™
AEROSOL MONITOR
MODEL 8520
APPLICATION NOTE ITI-044
Introduction
The DUSTTRAK™Aerosol Monitor Model 8520 offers several methods for reading aerosol mass
concentration:
1. The front panel displays aerosol concentration in real time.
2. The data logging feature allows users to record and view historical data about aerosol concentration
using a computer and TRAKPRO™Data Analysis Software.
3. Remote serial data acquisition and control via the DUSTTRAK™monitor’s RS-232 serial port.
4. Remote analog data acquisition via 0 to 5 VDC analog output feature built into all DUSTTRAK™
monitor's with serial numbers 22499 and higher. Most older units can have this feature added.
This application note concerns remote serial data acquisition and control (item 3) only. For information on
the other methods listed above, refer to the DUSTTRAK™Operation and Service Manual and/or
Application Note ITI-073 Analog Output for the TSI DUSTTRAK™Aerosol Monitor Model 8520.
The RS-232 serial data acquisition and control option has been incorporated into all DUSTTRAK™Model
8520 Aerosol Monitors manufactured on or after October 31, 1996. You can find the date of manufacture
listed on the serial number tag. For DUSTTRAK™monitor users with instruments which pre-date this
enhancement, the firmware will be automatically upgraded when the unit is returned to TSI or a TSI
authorized service center for servicing and calibration. If the date on the white calibration tag is November
1996 or later, the unit has already been upgraded.
The firmware which operates the DUSTTRAK™monitor includes serial data output capabilities. Users are
able to configure the DUSTTRAK™monitor to automatically transmit the aerosol mass concentration
values through the serial interface cable using simple ASCII commands. The DUSTTRAK™monitor can be
set to automatically transmit a reading once per user-defined interval (from 0 to 60 seconds) or to output
a single concentration reading. This allows DUSTTRAK™monitor users to monitor aerosol fluctuations in
real time using a data-logger or personal computer. The information may be used for closed-loop control
and/or monitoring applications.
Technical Specifications
The DUSTTRAK™monitor already includes the cable necessary to do serial data acquisition. The
connector required for the RS-232 port is an eight pin, RJ-45 modular connector. The DUSTTRAK™
monitor transmits serial data as ASCII character codes. The specifications for serial communication are
shown in the following table. The data string is terminated with carriage return/line feed (0D/0A
hexadecimal).
-2-
Baud Rate:
1200
Data Bits:
8
Stop Bits:
1
Hardware Control:
None
Serial Commands
Command
(Upper
Case)
Returned
Value
Description
ASRVCK
sssssss
Returns a seven character string corresponding to any service conditions which may be
present. See below for detailed description.
ASPOLL
±vvv.vvv
Returns the seven character string displayed on the DUSTTRAK™LCD in mg/m3. (three
digits and a decimal point followed by three more digits)
ASDATAxx
±vvv.vvv
Returns a reading every xx seconds averaged over that time interval, where xx can range
from 01 seconds to 60 seconds. The seven character string is in mg/m3(format is the same
as "ASPOLL").
NOTE: THE ASDATA FUNCTION DOES NOT WORK PROPERLY FOR DUSTTRAK™
MONITORS WITH FIRMWARE REVISIONS BELOW v1.9.
AQDATA
none
Terminates the "ASDATAxx" output stream.
ASRVCK
The DUSTTRAK™monitor can be polled for any service conditions which may be present using the
command "ASRVCK". This command can be issued to the DUSTTRAK™monitor to clear any service
condition which may be present during startup, as well as any time during normal operation. The
DUSTTRAK™monitor will return a seven character string which corresponds to the seven service
conditions which may arise. For example a returned string of "0000000" corresponds to no service
conditions (normal operation), a string of "0000001" corresponds to a service condition 1, while a string of
"7000300" corresponds to a service condition 7 and a service condition 3. The returned string may
contain any combination of the seven service codes when they are present.
Service
Code
Service Code Description
1
Memory has been cleared due to temporary loss of power from internal backup battery.
2
Calibration memory error. Internal calibration data corrupted.
3
Backup battery low.
4
The sample inlet nozzle is due for cleaning.
5
Internal filters are due for replacement.
6
The internal pump is failing or has failed.
7
Laser failure.
ASPOLL
The DUSTTRAK™monitor can be polled for the current aerosol concentration, averaged over the time
constant being used by the DUSTTRAK™monitor, with the command "ASPOLL". The returned seven
character string (three digits, a decimal point and three more digits) represents the average mass sum in
mg/m3. If the average mass is negative, then the seven character string will be preceded by a minus sign.
TSI Incorporated –Visit our website www.tsi.com for more information.
USA Tel: +1 800 874 2811
UK Tel: +44 149 4 459200
France Tel: +33 4 91 11 87 64
Germany Tel: +49 241 523030
India Tel: +91 80 67877200
China Tel: +86 10 8251 6588
Singapore Tel: +65 6595 6388
ITI-044 Rev. B (9/26/2012) ©2012 TSI Incorporated Printed in U.S.A.
ASDATAxx , AQDATA
The DUSTTRAK™monitor will output continuous data averaged over a user-defined time interval using the
command "ASDATAxx", where xx is a two digit value from 01-60, and represents time in seconds. The
data is averaged over the user defined time interval and is output every xx seconds. The returned seven
character string (three digits, a decimal point and three more digits) represents the average aerosol
reading in mg/m3. The data output will continue until the command "AQDATA" is received by the
DUSTTRAK™monitor.
NOTE
THE ASDATA FUNCTION DOES NOT WORK PROPERLY FOR
DUSTTRAK™MONITORS WITH FIRMWARE REVISIONS BELOW v1.9.
Serial Interface Connections
With the instrument lying flat on a table face up with the data port facing you, pin 1 is on the right side and
pin 8 is on the left.
Data Port Pin Assignments
Pin Number
Function
Direction
1
Not used
2
Not used
3
Receive data (Rx)
To DUSTTRAK™monitor
4
Data Set Ready (DSR)
From DUSTTRAK™monitor
5
Transmit data (Tx)
From DUSTTRAK™monitor
6
Not used
7
Signal Ground (G)
8
Data Terminal Ready (DTR)
To DUSTTRAK™monitor
Cable Wiring for Communications with IBM-PC compatible Computer Using
25-Pin, or 9-Pin RS-232 Port
Instrument Data Port
Pin
Computer 25-Pin Connector
(Use TSI 800560 Cable)
Computer 9-Pin Connector
(Use TSI 800563 Cable)
1
8
1
2
5
8
3
2
3
4
6
6
5
3
2
6
22
9
7
7
5
8
20
4
Other manuals for DustTrak 8520
1
Table of contents
Other TSI Instruments Measuring Instrument manuals
TSI Instruments
TSI Instruments 3321 Operation manual
TSI Instruments
TSI Instruments HM685 User manual
TSI Instruments
TSI Instruments 4199 Operation manual
TSI Instruments
TSI Instruments VelociCheck 8330 Operation manual
TSI Instruments
TSI Instruments Quest The Edge User manual
TSI Instruments
TSI Instruments P-TRAK Ultrafine Operation manual
TSI Instruments
TSI Instruments TF Series User manual
TSI Instruments
TSI Instruments EG4 User manual
TSI Instruments
TSI Instruments ALNOR AXD 530 User manual
TSI Instruments
TSI Instruments QUESTemp 32 User manual
TSI Instruments
TSI Instruments 5200 Series User manual
TSI Instruments
TSI Instruments 4040 Operation manual
TSI Instruments
TSI Instruments ALNOR 9880 User manual
TSI Instruments
TSI Instruments Alnor AirGard 405 User manual
TSI Instruments
TSI Instruments 8495 Operation manual
TSI Instruments
TSI Instruments VELOCICALC 9515 Operation manual
TSI Instruments
TSI Instruments DustTrak 8520 Operation manual
TSI Instruments
TSI Instruments AIRASSURE 8144 User manual
TSI Instruments
TSI Instruments Quest Edge 7 User manual
TSI Instruments
TSI Instruments Q-Trak XP Operation manual
