TSI Instruments 4043 Operation manual
GENERAL PURPOSE
THERMAL MASS FLOWMETER
MODEL 4040/4043/4045
OPERATION AND SERVICE MANUAL
P/N 1980339, REVISION J
FEBRUARY 2016
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
GENERAL PURPOSE
THERMAL MASS FLOWMETER
MODEL 4040/4043/4045
OPERATION AND SERVICE MANUAL
P/N 1980339, REVISION J
FEBRUARY 2016
U.S. & INTERNATIONAL TSI Instruments Ltd. (UK)
Sales and Customer Service: Sales and Customer Service:
(800) 874-2811 / +1(651) 490-2811 +44 (0) 1494 459200
Fax: Fax:
+1(651) 490-3824 +44 (0) 1494 459700
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
iii
CONTENTS
CHAPTERS
1 UNPACKING AND PARTS IDENTIFICATION ............................. 1
2 SETTING-UP ................................................................................. 3
Supplying Power ............................................................................ 3
Connecting Filter and Flow Tubes ................................................. 4
RS232 Configuration and Operation ............................................. 4
Configuration Software .................................................................. 5
3 OPERATION ................................................................................. 7
Overview ........................................................................................ 7
ON/OFF Switch ............................................................................. 7
Warm-up Time ............................................................................... 7
Flow Rate Measurement ............................................................... 7
Temperature Measurement ........................................................... 8
Pressure Measurement ................................................................. 8
Volume Measurement ................................................................... 8
4 MAINTENANCE ............................................................................ 9
Flow Sensor ................................................................................... 9
Re-certification ............................................................................... 9
Cases ............................................................................................ 9
Storage .......................................................................................... 9
5 TROUBLESHOOTING ................................................................ 11
APPENDIXES
A SPECIFICATIONS* ..................................................................... 13
B STANDARD FLOW RATE VS. VOLUMETRIC FLOW RATE.... 17
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
1
Chapter 1
Unpacking and Parts Identification
Carefully unpack the instrument and accessories from the shipping
container. Check the individual parts against the list of components in
Table 1. If any parts are missing or damaged, notify TSI immediately.
Table 1. List of Components
Qty
Item Description
Part/Model
1
Mass Flowmeter, 22 mm ISO tapered inlet/outlet
Mass Flowmeter, 0.50 inch inlet/outlet
Mass Flowmeter, 0.75 inch inlet/outlet
4040
4043
4045
1
Computer Cable
1303583
1
Analog Cable
1303584
1
Filter
22 mm ISO-taper (for Model 4040)
3/8” Female NPT (for Model 4043/45)
1602292
1602300
1
AC Adapter
100 to 240 V, N. America NEMA 5-15 plug, grounded
100 to 240 V, Europlug, CEE 7/16, grounded
100 to 240 V, Great Britain, grounded, fused
100 to 240 V, Australia/NZ
8918-NA
8918-EC
8918-GB
8918-AT
1
Operation and Service Manual
1980339
1
RS232 Serial Command Set manual
1980340
1
Carrying Case (optional accessory)
1319176
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
Chapter 1
2
Parts Identification
Figure 1-1 Model 4040/4043/4045 Mass Flowmeter
1. On/Off Switch
4. DC Power Input
2. Display
5. Flow Inlet
3. Mounting Inserts (2)
6. Computer Serial Interface and
Analog Output and Optional
Power Input Connector
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
3
Chapter 2
Setting-Up
Supplying Power
The flowmeter can be powered in one of two ways: through the power
jack using the supplied AC adapter or through the mini-DIN
connector. The DC power input connector is shown below along with
the power requirements.
Power Supply: 7.5 VDC ± 1.5 V, 300 mA maximum
When supplying power through the TSI-supplied interface cable, line
up the arrow on the connector with the bottom side of the flowmeter.
Flowmeter connector pin-out designations are shown below.
Table 2. List of Connector Pin-outs and
Cable Color Code Designations
Pin
Function
Cable Color
Code
1
Power Input (+)
Black
2
Power Ground (-)
Green
3
Analog Output (+)
Red
4
Analog Ground (-)
Brown
5
(no connection)
Blue
6
RS232 Receive (in)
White
7
RS232 Transmit (out)
Yellow
8
Logic Ground
Gray
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
Chapter 2
4
Connecting Filter and Flow Tubes
The Models 4040/4043/4045 have an exposed thermal flow sensor,
which must be protected from foreign matter and particles in the gas
flow. TSI has supplied a filter, which should be connected to the inlet
of the flowmeter; however, any filter will work as long as it has a
minimum efficiency of 99.9%.
Caution
Always use a filter on the inlet of the flowmeter.
Failure to filter the gas flow may change the
calibration and/or permanently damage the
sensor.
Note: Flow direction is identified by the large arrow printed on the
bottom side of the flowmeter.
After attaching the filter, connect the flow tube, to the inlet, of the
filter. Connecting a tube to the outlet of the flowmeter will create back
pressure. See Appendix A for flowmeter accuracy specifications when
operating at various pressures. In general, minimize back pressure on
the flowmeter to maintain higher accuracy.
RS232 Configuration and Operation
Many flowmeter operating parameters can be easily configured
through the RS232 serial port. Likewise, the flow rate, temperature,
pressure, and volume can be read through the serial port. Refer to
the Series 4000/4100 RS232 Serial Command Set manual for a
detailed description of the commands and command syntax.
RS232 Settings: Baud Rate ........ 38.4 k
Data Bits .......... 8
Parity ................ None
Stop Bits .......... 1
Flow Control ..... None
Table 3. Changeable Operating Parameters
Function
Command
Select Gas Calibration (air, oxygen, mixture)
SG
Select Oxygen Concentration in Air (21% to 99%)
SGM
Select Standard or Volumetric Flow Measurement
SU
LCD Display Update Rate (controls averaging)
SUR
Select Data Update Rate for Analog Output
SSR
Set Analog Output Full-Scale Flow Rate Value
SAS
Set Analog Output Zero Value
SAZ
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
Operation
5
Configuration Software
TSI has several software utilities to help you communicate with your
flowmeter to change parameters and to obtain flow data. You can
download the latest versions of these at no charge from our web site:
1. If you only want to change one or more of the operating
parameters shown in Table 3 (above), the easiest way is to use
the software utility called “TSI setup.” This uses convenient drop-
down menus to help change these parameters. After you have
made your changes, be sure to click on “Send” to store the
changes in the flowmeter’s memory.
2. If you want to communicate directly with the flowmeter using the
basic RS232 commands shown in the Serial Command Set
Manual, you can use a terminal program. HyperTerminal is a
common terminal program that is included with most versions of
the Microsoft operating system. You can download a document
from our web site that helps you configure HyperTerminal.
Download the document called “Using HyperTerminal to
communicate with TSI Flowmeters.”
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
7
Chapter 3
Operation
Caution
TSI flowmeters are not medical devices under
FDA 510k and in no situation should they be
utilized for human respiration measurements.
Overview
The Models 4040/4043/4045 Flowmeters measure mass flow rate,
temperature and absolute pressure of the gas inside the flow tube. All
measurements made by the Model 4040/4043/4045 are NIST
traceable.
ON/OFF Switch
Slide the switch to the ON position. The power switch is marked in the
international symbols '|' for on and 'O' for off. The flowmeter will begin
to simultaneously display flow rate, temperature and pressure.
Warm-up Time
The flowmeter will provide readings immediately upon power-up.
Recommended warm-up time of the flowmeter is 5 minutes.
Flow Rate Measurement
Flow rate data can be obtained from the Models 4040/4043/4045
through the LCD display, RS232 serial port or the linearized analog
output. The analog output is a 0 to 10 volt DC linear signal
representing 0 to 300 Std L/min (Model 4043: 200 Std. L/min) (analog
output scaling is user selectable). Refer to the RS232 Serial
Command Set manual for instructions on how to obtain flow data
through the serial port.
Gas calibrations (air, 100% nitrogen, 100% oxygen, or air/oxygen
mixtures) can be selected through the RS232 serial port. Refer to the
RS232 Serial Command Set manual for instructions on how to select
gas calibrations. The LCD display will indicate the calibration being
utilized, air or O2. When air/oxygen mixtures are being measured, the
LCD display will illuminate both the air and oxygen symbols. When
nitrogen is selected no gas type is displayed on the LCD.
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
Chapter 3
8
Flow can be displayed in units of standard liters per minute
(Std L/min*) or in volumetric units of liters per minute (L/min). Refer to
Appendix B for a description between the two measurements.
Selecting between the two measurements is accomplished through
the serial port. Refer to the RS232 Serial Command Set manual for
instructions on how to select between flow units.
Temperature Measurement
The Models 4040/4043/4045 have an independent temperature
transducer in the flow tube to measure the gas temperature. The
temperature sensor is used for temperature compensation of flow rate
and for converting flow from standard to volumetric units.
Temperature is displayed on the LCD and is available through the
RS232 serial port in the units of degrees Celsius (°C).
Note: At low flow rates, the temperature inside of the flow tube will
increase because of the heat generated by the thermal flow
sensor. This effect is normal and the temperature of the
incoming gas will be measured once flow resumes.
Pressure Measurement
The Models 4040/4043/4045 measure absolute pressure near the
outlet of the flowmeter in the SI units of kilo-Pascals (kPa). Pressure
measurements are required when converting from standard to
volumetric flow. Absolute pressure measurements are displayed on
the LCD display and are available through the RS232 serial port.
Volume Measurement
The Models 4040/4043/4045 measure total volume by integrating flow
over time. This is a calculated measurement performed by the
flowmeter and is only available using the RS232 serial port. Volume is
not displayed on the LCD display. Refer to the Models
4040/4043/4045 RS232 Serial Command Set manual for instructions
on using the volume function.
*TSI instruments defines standard conditions as 21.1°C (70° F) and 101.3 kPa (14.7
psia, 1 bar).
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
This manual suits for next models
2
Table of contents
Other TSI Instruments Measuring Instrument manuals
TSI Instruments
TSI Instruments DustTrak 8520 Operation manual
TSI Instruments
TSI Instruments DUSTTRAK 854201-M1 User manual
TSI Instruments
TSI Instruments TF Series User manual
TSI Instruments
TSI Instruments ALNOR AVM440 Operation manual
TSI Instruments
TSI Instruments 3082 User manual
TSI Instruments
TSI Instruments QUESTemp 32 User manual
TSI Instruments
TSI Instruments AIRASSURE 8144 User manual
TSI Instruments
TSI Instruments 5300 Series Setup guide
TSI Instruments
TSI Instruments VelociCalc 9515-AC Operation manual
TSI Instruments
TSI Instruments HM685 User manual
TSI Instruments
TSI Instruments 3302A User manual
TSI Instruments
TSI Instruments VelociCalc 9600 Series Operation manual
TSI Instruments
TSI Instruments SIZER 3321 User manual
TSI Instruments
TSI Instruments Alnor AirGard 405 User manual
TSI Instruments
TSI Instruments 3936 SMPS User manual
TSI Instruments
TSI Instruments Cheetah CH-5 User manual
TSI Instruments
TSI Instruments AccuBalance 8370 Operation manual
TSI Instruments
TSI Instruments HM675 Operating and maintenance instructions
TSI Instruments
TSI Instruments DustTrak DRX User manual
TSI Instruments
TSI Instruments Airflow TA500 Series Operation manual
