TPI 709R User manual

TPI 709R

Combustion Analyser

Contents

1. Introduction

2. Instrument Overview

2.1 Front View

2.2 Back View

2.3 Side Views

2.4 Top View

3. Turning On & Fuel Selection

3.1 Turning On

3.2 Fuel Selection

4. The 5 Functions

4.1 Function 1: - Flue Gas Analysis

4.2 Function 2: - Temperature Reading

4.3 Function 3: - Pressure Testing

4.4 Function 5: - Date/Time

5. Saving Data

6. Reviewing Data

7. Printing Data

8. Turning Off & Charging

9. Holding Data on Screen

Appendix A Specifications

Appendix B Calibration & Service

Appendix C Guarantee

Appendix D Troubleshooting Guide

Appendix E Index

1. Introduction

Thank you for purchasing TPI brand products. The TPI 709R Combustion

Analyser is a state of the art, easy to use analyser designed not only to display

and calculate the required readings from a flue but also to cover most of the other

desirable parameters associated with appliance installation and maintenance.

The instrument is ruggedly constructed and comes with a limited 3 Year

Warranty.

This manual will guide you through the functions of the TPI 709R, which will give

you many years of reliable service. The TPI 709R software has in-built self-

diagnostics that can easily be interrogated by our fully qualified and professional

engineers should an error occur. Please call the number below before returning

your instrument to your distributor should an error occurs. We can rectify over

75% of proposed faults over the phone.

TPI HELPLINE

01293 530196

Your TPI 709R Combustion Analyser comes complete with the following items as

standard: -

TPI 709R Instrument

Rubber Boot

Soft Carrying Case

Sampling Probe (c/w Type “K” Thermocouple)

In-Line Water Trap Bowl Filter (c/w Spare Particle Filter)

Battery Charger

Mini In-Line Pump Protection Filter (c/w 5 spare filters)

Exhaust Spigot (removable)

Pressure Tubing (2 x 1 metres)

GK11M Air Probe

Instruction Manual

Your TPI 709R Combustion Analyser has the following options available: -

Infrared Printer (see Appendix B)

Various Temperature Probes (see Appendix B)

Oil Filter (see Appendix B)

Smoke Test Pump (see Appendix B)

2. Instrument Overview

2.1 Front View

Rubber Boot Protects the instrument from accidental damage

Display Large 3 Parameter Backlit Display

Battery Indicator Showing battery life

Selected Fuel Type N Gas, LPG, Light Oil or Heavy Oil

Scrolls through selectable fuels (see 3.2)

Switches between Gross and Nett Efficiency (see 4.1.4)

Switches between ºC and ºF (see 4.2.1)

Scrolls through mbar, kPa and inH2O (see 4.3.1)

Moves up through the Stored Data Addresses (see 5, 6 & 7)

Zeroes pressure reading (see 4.3.1)

Moves down through the Stored Data Addresses (see 5, 6 & 7)

Scrolls through Flue Gas Analysis Function Screens (see 4.1)

Turns ch2 temperature ON/OFF (see 4.3.1)

Allows you to change the Date and Time (see 4.4)

Allows you to choose a Stored Data Address (see 5, 6 & 7)

Sends stored data to a separate infrared printer (see 7)

Allows you to view stored data on the display (see 6)

Stores readings to memory (see 5)

Moves you through the 4 Functions (see 4)

Turns Backlight ON and OFF (see 4)

Turns the instrument ON and OFF (see 3.1 & 8)

2.2 Back View

Gas and Pressure Inlet Ports Connection for In-Line Pump Protection Filter

(see 2.4 & 3.1)

Connections for Pressure Tubing (see 2.4 & 4.3)

Calibration and Info Label Displays calibration information

Displays serial number

Battery Compartment Holds rechargeable battery

Rubber Boot Protects the instrument from accidental damage

2.3 Side Views

Exhaust Port Port for connection of Exhaust Adaptor

Infrared Window Window for sending stored data to IR Printer (see 7)

Rubber Boot Protects the instrument from accidental damage

2.4 Top View

Charger Socket Connection for 220V/115V charger (see 10.1)

Thermocouple (ch1) Connection for thermocouple plug on probe (see 4.1)

T1 Socket Connection for any ‘K’ type thermocouple probe (see 4.2)

Thermocouple (ch2) Connection for any ‘K’ type thermocouple probe (see 4.2)

T2 Socket

Gas Inlet Port Connection for In-Line Pump Protection Filter (see 3.1)

Pressure (+) Port Connections for Pressure Tubing (see 4.3)

Pressure (-) Port Connections for Pressure Tubing (see 4.3)

3. Turning On & Fuel Selection

3.1 Turning On

Always: - Before turning on please ensure

that the In-Line Pump Protection Filter

(shown across) is connected to the Gas

Sample Port (see 2.2 or 2.4).

**THIS MUST REMAIN ON THE UNIT

AT ALL TIMES.**

Failure to do so may result in pump failure

and will invalidate the warranty.

Press the Power Key for approximately 2 seconds and the TPI 709R will

start up and display ALL Segments on the display for approx. 1 second. The

709R will then enter its 30-second purge period countdown with the following

screen being displayed.

The instrument should ALWAYS be turned

on in a clean air environment as the 30

second purge will attempt to set the Carbon

Monoxide level to 0 ppm and the Oxygen to

20.9%.

If there is insufficient clean air in the sensor

chamber after the 30 second purge period an

error indicating this may be displayed, please

see troubleshooting guide (appendix D) for

appropriate remedy. If the error is still present

after attempting the suggested remedy please

call the TPI HELPLINE

01293 530196

3.2 Fuel Selection

During the last 20 seconds of the 30 second purge time (i.e. as the 709R counts

down from 19 to 0) the user can scroll through the following Fuels: - Natural Gas,

LPG, Light Oil & Heavy Oil by repeatedly pressing the

Up Arrow Key to select the Fuel they are working with.

4. THE 4 FUNCTIONS

After the 30-second countdown the instrument is ready to take Flue Gas,

Temperature or Pressure readings and will Display the following Screen.

You are now ready to take Flue Gas Analysis

Readings. Please continue on with the manual from

Section 4.1 (below) which will guide you through the

various Analysis Screens.

However, if you do not wish to perform a Flue Test at

this moment Press the Func/Backlight Key

and move onto Section 4.2 of the manual.

At any time you can activate the Backlight by holding down the

Func/Backlight Key for 2 seconds.

4.1 Function 1: - Flue Gas Analysis

Ensure you have connected the Temperature Sampling Probe complete with

In-Line Water Trap Bowl Filter to the In-Line Pump Protection Filter (See 3.1)

which should ALWAYS be connected to the Gas Sample Port (see 2.2 or 2.4)

and that the ‘K’ Type Thermocouple Plug is in Thermocouple Socket (ch1)

(see 2.4). Also ensure that a ‘K’ Type Air Probe is connected to

Thermocouple Socket (ch2) (see 2.4) in order to calculate efficiency.

Other manuals for 709R

This manual suits for next models

Table of contents

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual