Topkodas GTalarm2 Assembly instructions

GTalarm2

Installation & Programming Manual

Security, monitoring and automation system

This manual includes steps to set up and use your system.

The module GTalarm2 is a security, automation and access control

system with 6 zone inputs that is expandable to 32 zones, 6 analog inputs

0-10 V, 2 analog inputs 0-20 mA, 4 outputs 24 V /1000 mA open drain. 3

digital input/outputs The module GTalarm2 features up to 800 users, 32

sensors can be supported in any combination.

The module GTalarm2 provides the high level of protection residential

homes and any place where high security and automation is essential.

These systems are designed to be easy to use, and the modular concept

of these systems provides installers with labor-saving features that make

expanding, installing and servicing these systems quick and convenient.

Expand the module GTalarm2 by adding expansion module anywhere

and in any combination on the 1-wire bus. The Module is connected to the

bus at the most convenient location and then their zone inputs are

assigned to the desired zone and partition. Also, only a module’s used

inputs are assigned to zones in the system.

Once installed, all bus modules, including motion detectors, can be

programmed remotely via GPRS connection or via USB using SERA2

upload/download software.

The zones can be used to automate PGM activations.

The module GTalarm2 is a logical solution to every installer’s security,

access control and home automation installation needs.

Features of the module GTalarm2



Communication via SIA IP DC09 protocol



4 Analog inputs (pull up 5.1K) 0-10V



2 Analog Input/ Output , 0-10V , 0-20mA



3 Digital Inputs/Outputs 3.3V , 20mA,



Wiegand interface, Dallas 1-Wire Bus



4 PGM outputs 24V/1000mA. Open Drain.



Up to 32 sensors, temperature, humidity etc.



Digital expansion module BUS.



Built-in access control features



In-field firmware upgradeable via USB and SERA2 software



Events log buffer. 2048 events



Program remote controls using the master or installer codes



Up to 800 users remote controls with mob phone,



Up to 800 users remote controls with iButton or RFID keycard



Up to 800 user code. To control with Wiegand keyboard.



Built-in-real-time clock backup battery



Unlimited control via SMS.



External microphone / speaker



Push button software reset

The meaning of icons in the manual:

Automation part

Security system’s part

Very important

Important

About the manual

Contents

1. General information about the module GTalarm2..................................................................................................................................................... 4

1.1. Specifications....................................................................................................................................................................................................4

1.2. Used definitions and terms...............................................................................................................................................................................4

1.3. Package content...............................................................................................................................................................................................5

1.4. General view of the module .............................................................................................................................................................................6

1.5. Meaning of LEDs and contacts........................................................................................................................................................................7

1.6. Inputs ................................................................................................................................................................................................................8

1.7. Outputs..............................................................................................................................................................................................................8

2. First steps to prepare GTalarm2 and SERA2 software............................................................................................................................................. 8

3. Installation................................................................................................................................................................................................................... 8

3.1. Power supply, Battery Wiring...........................................................................................................................................................................8

3.2. Humidity sensors AM2302/DHT22/AM2305/AM2306/AM2320/AM2321.......................................................................................................9

3.3. Analog inputs 0-10V, 0-20mA, 4-20mA.........................................................................................................................................................10

3.4. Temperature sensors Dallas 1-wire DS18b20 installation & recommendations..........................................................................................11

3.5. Burglar Alarm sensor zones wiring EOL NO NC...........................................................................................................................................12

3.6. Guidelines for Locating Smoke Detectors and CO Detectors ......................................................................................................................14

3.6.1. [4-Wire] Smoke detector Wiring................................................................................................................................................................14

3.6.2. [2-Wire] Smoke Detector Wiring to I/O Inputs..........................................................................................................................................15

3.7. Outputs. Bell & PGM Wiring...........................................................................................................................................................................16

3.8. Access control. Arming/ disarming methods.................................................................................................................................................17

3.8.1. Wiegand Keypad & RFID Card Reader Wiring........................................................................................................................................18

3.8.2. iButton keys...............................................................................................................................................................................................19

4. Programming ............................................................................................................................................................................................................ 21

4.1. SERA2 Uploading/Downloading Software.....................................................................................................................................................21

4.2. Security Programming Worksheets...............................................................................................................................................................22

4.3. General system options programming...........................................................................................................................................................23

4.4. System Fault/ Troubles Programming...........................................................................................................................................................24

4.5. Digital Inputs/ Outputs programming.............................................................................................................................................................26

4.6. Zones programming.......................................................................................................................................................................................27

4.7. 2-wire smoke detectors programming ...........................................................................................................................................................29

4.8. Outputs. Bell & PGM programming ...............................................................................................................................................................30

4.9. Users & Remote Control programming details..............................................................................................................................................31

4.10. Wiegand Keypad & RFID card reader programming....................................................................................................................................32

4.11. iButton keys & RFID programming................................................................................................................................................................33

4.12. DISARM /ARM/SLEEP/STAY the security system .......................................................................................................................................33

4.1. Reporting SMS&Dial in Case of Alarm Events..............................................................................................................................................34

4.1.1. Reporting to the user‘s mobile phone.......................................................................................................................................................35

4.1.2. Custom SMS Text .....................................................................................................................................................................................36

4.2. Reporting to the Central Monitoring Station..................................................................................................................................................36

4.2.1. GPRS/ IP/ TCP/ UDP details programming .............................................................................................................................................36

4.2.2. Central Monitoring Station details programming......................................................................................................................................37

4.3. Event Summary (Events)...............................................................................................................................................................................38

4.1. RT Testing & Monitoring. Hardware. .............................................................................................................................................................39

4.2. RT Testing & Monitoring Security Alarm Panel/ Access...............................................................................................................................40

4.3. Automation & Sensors Programming ............................................................................................................................................................41

4.4. Sensors Configuration....................................................................................................................................................................................42

4.4.1. Humidity sensors AM2302/DHT22/AM2305/AM2306/AM2320/AM2321 Configuration.........................................................................42

4.4.2. Analog inputs 0-10V, 0-20mA, 4-20mA Configuration.............................................................................................................................43

4.4.3. Temperature sensors Dallas 1-wire DS18b20 Configuration ..................................................................................................................43

4.1. Automation/Sensors (Automation/Sensors/Analog Inputs) Programming in SERA2 Software...................................................................43

4.2. Data Transmiting to Server & Remote Control..............................................................................................................................................46

4.2.1. TCP/ IP Remote Control ...........................................................................................................................................................................46

4.3. Events Log......................................................................................................................................................................................................47

4.4. Remote Monitoring, Control, Configuration, FW update over the internet...................................................................................................48

4.5. Testing & Monitoring Automation...................................................................................................................................................................50

4.5.1. RT Testing & Monitoring > Sensors/ Automation.....................................................................................................................................50

4.5.2. RT Testing & Monitoring > Event Monitoring ...........................................................................................................................................51

5. Info: Hardware, Firmware, Bootloader, Serial No & Updates ................................................................................................................................. 51

6. Recommendations for the user & installer............................................................................................................................................................... 52

7. Remote control and configuration using SMS Commands..................................................................................................................................... 53

7.1.1. The table of installers commands.............................................................................................................................................................53

7.1.2. The table of users commands...................................................................................................................................................................55

8. Warranty Terms and Conditions .............................................................................................................................................................................. 56

1. General information about the module GTalarm2

1.1. Specifications

Parameters of built-in GSM module:

Quad-band (850/900/1800/1900 MHz)

Sending of SMS messages

Receiving of calls and dialing

Data download/upload via GPRS network

Outputs (PGM):

OUT1 max current –(-V) 1000 mA.

OUT2 max current –(-V) 1000 mA.

OUT3 max current –(-V) 1000 mA.

OUT4 max current –(-V) 1000 mA.

All outputs can be controlled via short call

DIAL or via SMS message. This feature may

be used for gate opening, ignition locking etc.

Output alarm parameters may be

programmed.

Programmable algorithms for outputs

operation: CTRL/SMS/DIAL, SIREN, BUZER,

ARM state, Zones OK, Light Flash, inverting,

pulse mode

IN1 - IN4 inputs:

SMS text for input alarm and restore

Available to control until 32 sensors

Programmable enabling or disabling of inputs;

Burglary alarm zones. Input type

NC/NO/EOL/EOL+TAMPER 2.2K + 2.2K

5.1K pull up resistor.

Analog input 0-10V

Algorithm for zones operation: delay, interior,

instant, 24 hours, silent, fire

Response time;

Time of additional response;

Commutation of selected output

Control of analog sensors

Inputs/outputs I/O1-I/O2:

Programmable input or output

Burglary alarm zones. Input type: NC/NO/EOL/

EOL+TAMPER

Analog 0-10V/0-20mA/4-20mA

Control of analog sensors

Digital inputs/ outputs D1-D3:

Programmable optional digital input or output

Max. Voltage 3.3V

Dallas 1-Wire Bus, DS18b20, DS1990A

Aosong 1-Wire bus Humidity Sensor

AM2302 DHT22 AM2305 AM2306 AM2320

AM2321

Wiegand interface DATA0/ DATA1, RFID

reader, Keyboard.

The total length of the bus from 10 to 100m.

Module control:

ARM/DISARM of the security system via:

„Key switch” input level or pulse mode.

SMS message 800 users

short call DIAL 800 users

Maxim-Dallas iButton key (iButton DS1990A –

64 Bit ID)) 800 users.

Wiegand keypad code or RFID keycard or key

fob 800 users

3.3V power source output for external

modules:

Voltage 3.3V

Current limit 100mA

BUS expansion modules or programmable

input/output:

Voltage 8-15V

Current 20mA

Automatic periodical test:

Test sending in a form of SMS message.

Periodicity for communication control

messages (tests) from 1 to 99 nights and

days according to selected time. Or fixed

periodical interval 1-99999 minutes.

Power supply voltage:

Nominal power supply voltage –12.6 V

Power supply voltage range 8 –15 V

Max. Allowed ripple voltage 100mV

Consumption current:

In standby mode less than 50 mA.

In dialing or SMS/GPRS sending mode

less than 300 mA.

Events Log:

Nonvolatile flash events log 2048 events

Environmental parameters:

Storage temperature range from -40 to

+85 oC / -40 to 185 oF

Operational temperature range from -30

to +75 oC / from -22 to 167 oF

Max relative humidity under +40 oC / 104

oF 95%

Package weight 90g

Module weight: 43g

Overall dimensions of the module:

84x66x18mm

1.2. Used definitions and terms

Term

Description

Alarm Log

Contains information about alarms that are currently active on the system or information about alarms that have been

raised and then resolved on the system. This log can be useful in analyzing problems and trends in the system.

Arming/Disarming

A process of enabling/disabling system's security.

Authorized user

It is a person whose mobile phone’s number is entered in GSM module. Two authorized users with the same rights may

be entered into the module.

Backup battery

The secondary power source of the system. In case of a main power failure, the backup battery will take over.

Bell squawk

If enabled, the siren/bell indicatesthe completed system arming and disarming process (exceptthe arming in STAYmode).

After the system is successfully armed, the siren/bell will emit 2 short beeps and 1 long beep after the system is disarmed.

By default, the parameter is disabled.

Bypass/Activate Zone

Zone bypassing allows the user to deactivate a violated zone and arm the system without restoring the zone. If a bypassed

zone is violated or restored during exit/entry delay, or when then system is armed, it will be ignored. The zone will remain

bypassed until the system is disarmed. Zones can only be bypassed and activated when the system is not armed.

Caller ID

Caller's identification

COM

Negative power supply terminal.

Confirmation timeout

Specifies the time in which a cross zone must be violated that the system could confirm alarm on the associated zone.

Configuration

Programming of the settings, which will define the operation of the item. For example, user's telephone numbers, set-up of

periodicity for sending SMS message, input names etc.

CMS

Central monitoring station

DIAL

The system makes a call to the number specified.

Diagnostic Tool

When using Configuration tool software, you may use a section of functions, that allows to monitor real-time zones, view

changes of peripheral devices, instantly configure necessary options, for example, enabling/disabling PGM outputs, etc.

Entry Delay

Once the exit delay has expired, the system initiates the entry delay countdown if a Delay type zone is violated. The

countdown is indicated by short beeps emitted by keypad buzzer and by steady beep emitted by system's buzzer. The

indication is intended to advise the user that the system should be disarmed. If the system is disarmed before the entry

delay expires, no alarm will be caused.

EOL

(End of line resistor) input type with resistor.

Event

The information that the user receives.

Event Log

A list of system events that is uploaded from the device‘s memory to the configuration software for further analysis. The

system logs all information about system configuration, system actions and info messages.

Exit Delay

A period of time intended for user to leave the secured area. The system begins the countdown after the arming process

initiation.

Fault

A specific problem or error that prevents the system from working properly. The system comes equipped with self-

diagnostic feature allowing to indicate the presence of any system fault by the keypad as well as by SMS text message

notification to the listed user phone number.

iButton key

A unique 64-bit ID code containing chip enclosed in a stainlesssteel tab usually implemented in a small plastic holder. The

module supports up to 800 iButton keys each holding a unique identity code (ID), which is used for system arming and

disarming.

Installer

a person provided with INST (installer's) password

Master/User Code

Allows to carry out system arming/ disarming as well as minor system configuration and control

MIC

microphone

Normally closed (NC)

It is a switch that passes current until actuated.

Normally open (NO)

It is a switch that must be actuated to pass current.

Periodic Test Event

Provides the following information on alarm system: date & time, status (armed/disarmed), GSM signal strength, mains

power supply status, temperature value measured by primary and secondary temperature sensors (if any).

Pull-up resistor

Is that it weakly "pulls" the voltage of the wire it is connected to towards +V (or whatever voltage represents a logic "high").

PGM output

A PGM output is a programmable output that toggles to its set up state when a specific event has occurred in the system,

the scheduled weekday and time has come or if the user has initiated the PGM output state change manually.

Ping period

Sets period of time defining how often the module sends ping data packet to the server.

Protocol

A formal specification for communicating; an IP address the special set of rules that end points in a telecommunication

connection use when they communicate. Protocols exist at several levels in a telecommunication connection.

Service messages

ARM/DISARM, test, resetting of the system.

SSR

Solid State Relay

SMS forward

System can re-sent all incoming SMS messages to the specified users. It is useful if the GSM operator of the inserted SIM

card sends some useful information (SIM card validation or payment account status and etc.) or it is necessary to monitor

all incoming SMS messages by specified user.

User

It is a person being aware USER password.

Zone

Detection devices such as motion detectors and door contacts are connected to the alarm system’s zone terminals.

Zone state/status

Zone status is a position of a certain zone being enabled or disabled. Meanwhile, zone state points out the condition of a

certain zone, which can either be violated (i.e. In case of alarm) or restored.

Positive power supply terminal.

1.3. Package content

Table 1 Standard package content

GTalarm2 module –1 pcs

GSM antenna - 1 pcs

Shipping Package - 1 pcs

2.2 kOhm resistors - 12 pcs

5.1 kOhm resistors –2 pcs

Spaces for PCB installation -

4 pcs

Package content may be vary without a notice. Ask the seller before buying!

Table 2 Additional, under request package content

External microphone with 1

m cable and connector

iButton probe with LED indicator

GSM antenna with cable

Mini USB cable

iButton DS1990A-F5+ key

Water Proof DS18b20 Temperature

Probe with 1m cable

Temperature sensor DS18B20

Humidity sensor AM2320

Humidity sensor DHT22

(AM2302)

Humidity sensor AM2305

Wiegand keypad & RFID reader

Mini CD - 1 pcs: User’s guide

in PDF Program SERA2

1.4. General view of the module

1. Micro SIM card holder of

“Push-Push” type

2. GSM antenna connector

3. RESET button

4. Mini USB programming

connector

5. REG (yellow) see table 3

6. DATA (red) see table 3

7. WDG (green) see table 3

8. Power supply and

input/output connector

9. External microphone

connector

Do not locate SIM card with force, because you may damage SIM card holder

SPK

MIC MIC

SPK

COM

Figure 1 GTalarm2 PCB Layout

1.5. Meaning of LEDs and contacts

Table 3 Meaning of LEDs

Name

Indication variations

Meaning

WDG (green) built-in

LED

Watchdog heart beat blinking, remains lit

for 50ms, and turns off after 1000ms.

The module is functioning.

Off

The module is out of order or no voltage

REG (yellow) built-in

LED

Lights continuously

Modem has been registered to the network

Flashes, remains lit for 50ms, turns off for

300ms

Modem is being registered to the GSM network.

Blinking fast, remains lit for 50ms turns off

for 50ms

PIN code of SIM card error. PIN code request should be removed or

correct PIN code should be entered.

Off

Modem failed to register to the network.

DATA (red) built-in LED

Lights continuously

The memory of the module contains unsent reports to the user or to the

server.

Off

All reports has been send.

Table 4 Terminal block. Contacts.

Contact No

Name

Max. voltage (V)

Optional functions and Description

VD+

Positive supply contact

Power supply voltage

8-15V

Current in standby mode

<50mA

Current when sending data

<300mA

COM

Negative supply terminal for keyboard(s), indicators and sensors.

BUS

Programmable functions

Expansion module data BUS

Output, 20mA

Input

Max available voltage

15V

4 … 7

OUT1 ...

OUT4

Programmable Output PGM1 - PGM4. Drain type. When state is ON, connects internally to COM

Max available current

1000mA

Max available voltage

24V

8, 9

I/O1-I/O2

Programmable functions

The zone for security system NC/NO/EOL/EOL+Tamper [1]

Output 20mA

Analog current input 0-20mA

Analog voltage input 0-10V

Max available voltage

15V

10 …

IN1 … IN4

Programmable functions

Input with 5.1K resistor to the VD+ (Pull UP)

The zone for security system NC/NO/EOL/EOL+Tamper

Analog input 0-10V

Max available voltage

15V

COM

Negative supply terminal for keyboard(s), indicators and sensors.

3.3

Programmable functions

Digital output

Digital input

Dallas 1-Wire bus. DS18b20, DS1990A

Aosong 1-Wire bus. Humidity Sensor AM2302, DHT22, AM2305,

AM2306

Wiegand (1) interface DATA1 , RFID reader, keypad

Max available voltage

3.3V

Max available current

20mA

3.3

Programmable functions

Digital output

Digital input

Dallas 1-Wire bus. DS18b20, DS1990A

Aosong 1-Wire bus. Humidity Sensor AM2302, DHT22, AM2305,

AM2306

Wiegand (1) interface DATA0 , RFID reader, keypad

Max available voltage

3.3V

Max available current

20mA

3.3

Programmable functions

Digital output

Digital input

Dallas 1-Wire bus. DS18b20, DS1990A

Aosong 1-Wire bus. Humidity Sensor AM2302, DHT22, AM2305,

AM2306

Max available voltage

3.3V

Max available current

20mA

3.3V

3.3

Power supply for external temperature, humidity sensors

Max available voltage

3.3V

Max available current

100mA

[1] If the zone used for security system purpose 5.1k pull-up resistor should be connected

1.6. Inputs

The module GTalarm2 has:

4 analog inputs (In1...In4 (0-10V)) for analog sensors connection. Or can be used or use it as security system‘s zones with selectable type:

NC/NO/EOL/EOL+TAMPER.

2 programmable analog inputs (I/O1, I/O2(0-10V/0-20mA)) for analog sensors control or using as security system‘s zone with selectable

type: NC/NO/EOL/EOL+TAMPER

3 programmable digital inputs (D1...D3(Max voltage 3.3V)) used for:

oDallas 1-Wire Bus. To connect temperature sensors DS18b20 or iButton key DS1990A,

oAosong 1-Wire bus Humidity Sensor AM2302, DHT22, AM2305, AM2306,

Wiegand interface DATA0/ DATA1, FID reader, Keyboard.

1.7. Outputs

The module GTalarm2 has:

4 open drain (1A) outputs: OUT1 (1A)… OUT4 (1A). The outputs can be used for siren, relay, lamp connection. These outputs can be

controledvia short call or sms. Output operation algorithms: Automation /CTRL, Siren, Buzzer, ARM state, Zones OK, Light Flash, inverting,

pulse mode

2 open drain (20mA) outputs: I/O1 (20mA)… I/O2 (20mA). These outputs can be used for solid state relays, LED, to control devices up to

20mA.

3 outputs:D1 (10mA, Max Voltage 3,3V) for LED, solid state relays control. Max voltage 3,3V

1 programmable output BUS. Voltage 8-15V, Current 20mA

OUT1… OUT4 max current – (-V) 1000 mA.

All outputs can be controlled via short call DIAL or via SMS message. This feature may be used for gate opening, ignition locking etc.

Output alarm parameters may be programmed.

Programmable algorithms for outputs operation: CTRL/SMS/DIAL, SIREN, BUZER, ARM state, Zones OK, Light Flash, inverting, pulse

mode

2. First steps to prepare GTalarm2 and SERA2 software.

Preparation procedure of the module GTalarm2.

Connect the GSM antenna to the antenna connector.

Insert the SIM card in the SIM card holder. Ensure that PIN request function is disabled.

Connect the module to the computer via mini USB cable.

Install configuration software SERA2.

Go to the http://topkodas.lt/ website and download SERA2 software.

Open the folder containing installation of the software SERA2. Click the file „SERA2 setup.exe“

If installation directory of the software is OK, press [Next]. If you would like to install the software in the other directory press [Change],

specify other installation directory and then press “next”.

Check if the correct data are entered and press Install

After successful installation of the software SERA2, press [Finish]

3. Installation

This Installation & Programming manual provides the basic installation, wiring and programming information required to program the module

GTalarm2 and connect all third party devices to the module.

You can find wiring diagrams in the Error! Reference source not found.. You can find detailed information about security system’s

configuration in the Error! Reference source not found.

3.1. Power supply, Battery Wiring

It is possible to supply the security

system from stabilized power supply

source 10-15 V and not less than

1,5A. It is necessary to calculate max

current of power supply. The current

of the alarm system is the current

used by sensors, relays, siren and

other devices. It is most convenientto

use power supply source applied for

powersupplyof securitysystemswith

the option to connect backup lead

battery. It is recommended to mount

remote control relays into sockets.

Sockets may be easily fixed in metal

box. It is necessary to select relays

according to preferred voltage and

current.

Figure 2 Power supply connection

AC equipment cannot be connected directly to the module. It is necessary to use a special relays or other methods, which are in

compliance with electrical safety requirements.

When controlling devices from the AC network, it is necessary to follow all electrical safety requirements.

3.2. Humidity sensors AM2302/DHT22/AM2305/AM2306/AM2320/AM2321

Module should work with following sensors: Aosong 1-Wire bus Humidity Sensor AM2302, DHT22, AM2305, AM2306. Also a new smaller sensor

exists AM2320 & AM2321.

Table 5 Sensors AM2302, AM2320/AM2321 specification

Manufacturers' Specification

AM2302

AM2320/AM2321

Operating Range

0–100

Absolute accuracy

(%RH, 25°C)

±3% (10-90%)

±5% (<10, >90%)

±3% (10-90%)

±5% (<10, >90%)

Repeatability (%)

±0.3

±0.1

Long term stability

(% per year)

0.5

1/e Response (sec)

Voltage supply (V)

3.3–5.5

3.1–5.5(AM2320)

2.6–5.5(AM2321)

The table lists values taken from datasheets. The Aosong data sheets do not specify maximum tolerances for most parameters, just 'typical'

values. It would therefore seem that any particular device is not guaranteed to meet these specifications. For all the other devices the numbers above

are the maximum tolerances and most also offer better 'typical' specifications.

Each AM2302 sensor connects on separate bus line to digital inputs (D1, D2, and D3). Total up to 3 AM2302 Aosong (Guangzhou) humidity

sensors can be connected to GTalarm2

Figure 17 AM2320 connecting diagram

Figure 18 AM2302 connecting diagram

Steps to start AM2320 and AM2302 sensors:

1. Connect AM2320 or AM2302 to D1, D2, D3 according connection diagram.

2. Sensor’s type should be select in the System Options> Digital I/O Settings window. Set digital input definition D1, D2, D3 to Aosong 1 Wire

bus Humidity Sensor AM2302

3. Write configuration

4. Power module.

5. After module starts, wait a minute while sensor will be found on the bus.

6. Read configuration

7. Go to “Automation/ Sensors” window in the SERA2 software

8. Double click on the selected sensor’s line.

COM

+12V

AC Fail

AC 18V

BAT+

BAT-

Externalpower supply

Transformer ~18-24V

BackupBattery 12V

OUT1

COM

BU S

OUT4

I/O1

IN4

IN3

IN2

OUT2

+3.3V

OUT3

VD+

COM

IN1

I/O2

GTalarm2

+3.3V

COM

AM2320

VC C

SC L

SD A

GND

D1, D2, D3

1234

+3.3V

COM

AM2302

VD D

SD1

GND

D1, D2, D3

1234

9. Click on “Sensor type/ hardware location” and default sensor settings appear.

10. In sensors table column Sensor HW ID find registered sensors AM2302 looks like "GTalarm, Input D1,1-Wire, AM2302 Huminidty"Location

of the sensor can be changed choosing wanted sensor in the list

11. Double click on the sensor row opens selected sensor window

12. Set other parameters of the sensor MIN, MAX values Units etc.

13. Write configuration to module

14. Open RT Testing&Monitooring Window > Hardware. Press [Start monitoring] button

15. Go to RT Testing&Monitooring Window > Event Monitoring TAB. Software will show real time sensor values, and alarm states

16. If you need to receive sms with sensors alarm, go to GSM Communication > SMS DIAL Reporting window. Enter telephone numbers of

users and markalarm events that you want to receive. Open "Reporting SMS&DIAL" window. Set user phone number,and choose reporting

option Sensor1 - Sensor32 Alarm/Restore. Module will send SMS to user then sensor alarm event occurs

17. Write configuration

3.3. Analog inputs 0-10V, 0-20mA, 4-20mA

Steps to start analog sensors:

1. Connect analog voltage sensors to IN1, IN2, IN3, IN4, and current

I/O1, I/O2 according connection diagram.

2. The analog inputs can be used as security system zones or

analog sensors.

3. If analog inputs sensors is not in use, the inputs should be

disabled in “Zones” or “Sensor” window.

4. Analog sensors should be calibrated in the Automation/Sensors

window. Double click on the selected sensor’s line. Analog

sensors could be selected from the default list. Units could be

changed. Sensors calibration is possible by changing multiplier,

offset.

5. When all changes has been done, the configuration should be

written to module, by pressing write icon.

6. Open RT Testing&Monitooring Window > Hardware. Press [Start

monitoring] button

7. Go to RT Testing&Monitooring Window > Event Monitoring TAB. Software will show real time sensor values, and alarm states

8. If you need to receive sms with sensors alarm, go to GSM communications > SMS Dial Reporting window. Enter telephone numbers of

users and mark alarm eventsthat you want to receive. Open "Reporting SMS&DIAL" window.Set user phonenumber, and choose reporting

option Alarm/Restore. Module will send SMS to user then sensor alarm event occurs

9. Write configuration

Any automation voltage analog sensors 0-10V, can be connected to IN1-IN4 (has internal pull up resistor 5.1K) , and I/O1, I/O2

Current measure analogue sensors can be connected to I/O1 and I/O2 0-20mA, 4-20mA

OUT1

COM

BU S

OUT4

I/O1

IN4

IN3

IN2

OUT2

+3.3V

OUT3

VD+

COM

IN1

I/O2

4-20mA0-10V

Figure 3 Analog sensor connection

Other manuals for GTalarm2

Table of contents

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual