Thermo Scientific Partisol 2000i User manual

Partisol 2000iAir Sampler/

Partisol 2000i-D Dichotomous

Air Sampler

Instruction Manual

Part Number 110735-00

14Apr2015

Specifications, terms and pricing are subject to change. Not all products are available in all countries. Please

consult your local sales representative for details.

Thermo Fisher Scientific

Air Quality Instruments

27 Forge Parkway

Franklin, MA 02038

1-508-520-0430

www.thermo.com/aqi

Thermo Fisher Scientific WEEE Compliance

WEEE Compliance

This product is required to comply with the European Union’s Waste

Electrical & Electronic Equipment (WEEE) Directive 2002/96/EC. It is

marked with the following symbol:

Thermo Fisher Scientific has contracted with one or more

recycling/disposal companies in each EU Member State, and this product

should be disposed of or recycled through them. Further information on

Thermo Fisher Scientific’s compliance with these Directives, the recyclers

in your country, and information on Thermo Fisher Scientific products

which may assist the detection of substances subject to the RoHS Directive

are available at: www.thermo.com/WEEERoHS.

Thermo Fisher Scientific Partisol 2000iand Partisol 2000i-D Instruction Manual i

About This Manual

This manual provides information about installing, operating, maintaining,

and servicing the Partisol 2000iAir Sampler and the Partisol 2000i-D

Dichotomous Air Sampler. It also contains important alerts to ensure safe

operation and prevent equipment damage.

The manual is organized into the following chapters and appendices to

provide direct access to specific operation and service information.

●Chapter 1 “Introduction” introduces the user to the advanced features

of the Partisol 2000iand Partisol 2000i-D and describes the flow and

sampling configurations of the system. It also discusses the flow control

scheme used in the unit.

●Chapter 2 “Installation” describes how to unpack, set up, and start up

the Sampler.

●Chapter 3 “Filter Handling and Exchange” provides procedures for

handling, exchanging and transporting filters.

●Chapter 4 “Partisol 2000i Inlet Conversion” provides procedures for

configuring the Sampler with a variety of inlet systems.

●Chapter 5 “Operational Modes” describes the different operating

modes used on the Sampler.

●Chapter 6 “Sampler Settings” describes the different options available

for programming the Sampler.

●Chapter 7 “Sampler Operation” describes how to verify the Sampler’s

characteristics prior to starting a sampling run, programming a

sampling run, and retrieving data.

●Chapter 8 “Calibration” provides procedures for calibrating the

Sampler and calibration setup.

●Chapter 9 “Firmware Screen Descriptions” describes the front panel

display screens, the front panel pushbuttons, and the menu-driven

firmware.

●Chapter 10 “Preventive Maintenance” provides maintenance

procedures to ensure reliable and consistent instrument operation.

●Chapter 11 “Troubleshooting” presents guidelines for diagnosing

Sampler failures, isolating faults, and includes recommended actions for

restoring proper operation.

About This Manual

Safety

ii Partisol 2000iand Partisol 2000i-D Instruction Manual Thermo Fisher Scientific

●Chapter 12 “Servicing” presents safety alerts for technicians working on

the Sampler, step-by-step instructions for repairing and replacing

components, and a replacement parts list. It also includes contact

information for product support and technical information.

●Chapter 13 “Electronics” provides a description of the system

electronics and input/output connections.

●Appendix A “Warranty” is a copy of the warranty statement.

●Appendix B “C-Link Protocol Commands” provides a description of

the C-Link protocol commands that can be used to remotely control a

Sampler using a host device such as a PC or datalogger.

●Appendix C “MODBUS Protocol” provides a description of the

MODBUS Protocol Interface which is supported both over RS-

232/485 (RTU protocol) as well as TCP/IP over Ethernet.

●Appendix D “Communications Using iPort or RPComm” describes

RPComm communications software package which provides interactive

remote communications with Partisol instrumentation.

●Appendix E “AK Protocol” provides a description of the AK protocol

commands that can be used to remotely control a Partisol 2000iand

2000i-D using a host device such as a PC or a datalogger.

Review the following safety information carefully before using the Sampler.

This manual provides specific information on how to operate the Sampler.

If the Sampler is used in a manner not specified by the manufacturer, the

protection provided by the equipment may be impaired.

The seller cannot foresee all possible modes of operation in which the user

may attempt to utilize this instrumentation. The user assumes all liability

associated with the use of this instrumentation. The seller further disclaims

any responsibility for consequential damages. Use of this product in any

manner not intended by the manufacturer will void the safety protection

provided by the equipment, and may damage the equipment and subject

the user to injury.

Safety

About This Manual

Safety and Equipment Damage Alerts

Thermo Fisher Scientific Partisol 2000iand Partisol 2000i-D Instruction Manual iii

This manual contains important information to alert you to potential safety

hazards and risks of equipment damage. Refer to the following types of

alerts you may see in this manual.

Safety and Equipment Damage Alert Descriptions

Alert Description

DANGER A hazard is present that could result in death or serious

personal injury if the warning is ignored. ▲

WARNING A hazard or unsafe practice could result in serious

personal injury if the warning is ignored. ▲

CAUTION A hazard or unsafe practice could result in minor to

moderate personal injury if the warning is ignored. ▲

Equipment Damage A hazard or unsafe practice could result in property

damage if the warning is ignored. ▲

Safety and Equipment Damage Alerts in this Manual

Alert Description

WARNING If the Sampler is mounted on a stand, it could fall or tip

over in high wind conditions if the stand is not properly

anchored. ▲

The service procedures in this manual are restricted to

qualified service personnel only. ▲

If the equipment is operated in a manner not specified by

the manufacturer, the protection provided by the

equipment may be impaired. ▲

CAUTION If the LCD panel breaks, do not let the liquid crystal

contact your skin or clothes. If the liquid crystal contacts

your skin or clothes, wash immediately using soap and

water. ▲

Equipment Damage Do not attempt to lift the instrument by the cover or other

external fittings.

The stand must be anchored when installed outdoors to

prevent tipping of the Sampler and/or stand in high

winds.

Some internal components can be damaged by small

amounts of static electricity. A properly grounded

antistatic wrist strap must be worn while handling any

internal component. If an antistatic wrist strap is not

available, be sure to touch the instrument chassis before

Safety and

Equipment

Damage Alerts

About This Manual

FCC Compliance

iv Partisol 2000iand Partisol 2000i-D Instruction Manual Thermo Fisher Scientific

Alert Description

touching any internal components. When the instrument

is unplugged, the chassis is not at earth ground. ▲

Disconnect the serial cable before changing RS-232 and

RS-485 selection to prevent damage to any connected

equipment. ▲

Do not use solvents or other cleaning products to clean

the outside case. ▲

Do not remove the LCD panel or frame from the LCD

module. ▲

The LCD polarizing plate is very fragile, handle it

carefully. ▲

Do not wipe the LCD polarizing plate with a dry cloth, as

it may easily scratch the plate. ▲

Do not use alcohol, acetone, MEK or other ketone based

or aromatic solvent to clean the LCD module, but rather

use a soft cloth moistened with a naphtha cleaning

solvent. ▲

Do not place the LCD module near organic solvents or

corrosive gases. ▲

Do not shake or jolt the LCD module. ▲

Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

Note This equipment has been tested and found to comply within the

limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy,

and if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference, in

which case the user will be required to correct the interference at his or her

own expense. ▲

FCC Compliance

About This Manual

Electrical and Safety Conformity

Thermo Fisher Scientific Partisol 2000iand Partisol 2000i-D Instruction Manual v

This product has been tested by ETL Testing Laboratories, and has been

documented to be in compliance with the following U.S., Canadian, and

EU standards:

UL Standard 61010-1

CAN/CSA C22.2 NO. 61010-1

EN61010-1

Thermo Fisher Scientific certifies that this product operates in compliance

with the EC Directive 89/336/EEC with reference to electrical emissions

and immunity. Specifically, the equipment meets the requirements of

EN55011 Group 1, Class B (Emissions) and EN55082-1 (Immunity).

The hardware has been tested for personal or fire safety hazards, and meets

the requirements of UL/CSA/EN61010-1/UL61010-1 (Safety) in

fulfillment of EU Directive IEC 61326-1.

IEC 60529

Issued:2001/01/01 Ed:2.1 Degrees of Protection Provided by Enclosures

(IP Code); COR. No.1:2003; COR. No.2:2007; COR. No.3:2009

This operating manual includes references to the U.S. Environmental

Protection Agency (EPA) 2.12 Quality Assurance Handbook, Volume II,

Part II. Partisol Samplers that are installed as part of a U.S. EPA

monitoring network, or which must meet U.S. EPA monitoring

requirements, should refer to the procedures found in the U.S. EPA 2.12

Quality Assurance Handbook. The 2.12 Quality Assurance Handbook

provides general EPA-recommended guidance and, in some cases, may

provide additional, more detailed or more recent guidance.

A copy of the U.S. EPA 2.12 Quality Assurance Handbook can be obtained

from the AMTIC web site: http://www.epa.gov/ttn/amtic/pmqa.html, the

QC coordinator at any EPA Regional Office, or from the Monitoring and

Quality Assurance Group (MD- 14), U.S. EPA, Research Triangle Park,

NC 27711.

Electrical and

Safety Conformity

U.S. EPA Quality

Assurance

Specifications

C US

About This Manual

WEEE Symbol

vi Partisol 2000iand Partisol 2000i-D Instruction Manual Thermo Fisher Scientific

The following symbol and description identify the WEEE marking used on

the instrument and in the associated documentation.

Symbol Description

Marking of electrical and electronic equipment which applies to waste

electrical and electronic equipment falling under the Directive 2002/96/EC

(WEEE) and the equipment that has been put on the market after 13 August

2005. ▲

The following information can be used to determine the power service

requirements of this product:

Line Voltage

115VAC, 50-60Hz, 10 Amp

220-240VAC, 50-60Hz, 5 Amp

This instrumentation from Thermo Fisher Scientific is covered by pending

patents in the United States of America and other countries.

This documentation contains trade secrets and confidential information

proprietary to Thermo Fisher Scientific. The software supplied with the

instrumentation, documentation and any information contained therein

may not be used, duplicated or disclosed to anyone, in whole or in part,

other than as authorized in a fully executed Thermo Fisher Scientific End

User License Agreement or with the express written permission of Thermo

Fisher Scientific.

Partisoland the “rp” logo are registered trademarks of Thermo Fisher

Scientific. Other trademarks are the property of their respective holders.

Streamlineis a trademark of Chinook Engineering, LLC.

VSCCand Very Sharp Cut Cycloneare trademarks of BGI, Inc. Some

content of this manual is courtesy of BGI, Inc.

EEE Symbol

Equipment Rating

Patents,

Copyrights and

Trademarks

This manual suits for next models

Table of contents

Other Thermo Scientific Measuring Instrument manuals

Thermo Scientific

Thermo Scientific Smart-Vue User manual

Thermo Scientific

Thermo Scientific SOLA II Flare User manual

Thermo Scientific

Thermo Scientific Orion 8010cX User manual

Thermo Scientific

Thermo Scientific Orion Star A220 Series User manual

Thermo Scientific

Thermo Scientific G100 Series User manual

Thermo Scientific

Thermo Scientific Orion Versa Star User manual

Thermo Scientific

Thermo Scientific NanoDrop Lite Instruction Manual

Thermo Scientific

Thermo Scientific Orion Star A329 User manual

Thermo Scientific

Thermo Scientific 42iQLS User manual

Thermo Scientific

Thermo Scientific AutoXP User manual

Thermo Scientific

Thermo Scientific Orion 7070iX Owner's manual

Thermo Scientific

Thermo Scientific Orion AquaMate 8000 UV-Vis User manual

Thermo Scientific

Thermo Scientific 60i User manual

Thermo Scientific

Thermo Scientific RadEye B20 How to use

Thermo Scientific

Thermo Scientific Orion AquaMate UV-Vis User manual

Thermo Scientific

Thermo Scientific SPECTRONIC 200 User manual

Thermo Scientific

Thermo Scientific Sarasota FD910 User manual

Thermo Scientific

Thermo Scientific XL2 User manual

Thermo Scientific

Thermo Scientific Orion Versa Star VSTAR-PH User manual

Thermo Scientific

Thermo Scientific Orion 2230XP User manual

Thermo Scientific

Thermo Scientific Multiskan FC User manual

Thermo Scientific

Thermo Scientific 42i User manual

Thermo Scientific

Thermo Scientific Eutech EC 1720 User manual

Thermo Scientific

Thermo Scientific Star Series User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual