Texmate Tiger 320 Series Configuration guide

Texmate, Inc.Tel. (760) 598-9899 • www.texmate.com•Linearizing Supplement (NZ207) Page 1

Associated Documents

TTiiggeerr332200SSeerriieessLINEARIZING SUPPLEMENT

Technical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Linearization Using 32 Flexible Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Linearization Table Setup Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Linearization Configuration Programming Codes . . . . . . . . . . . . . . . . . . . . .7

Linearization Table Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Code 1 – Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Code 2 – Standard Thermocouple or RTD Linearization for CH1 . . . . . . .10

Code 3 – Non-preconfigured Linearization for CH1 . . . . . . . . . . . . . . . . . .11

Code 4 – Linearization for Channel 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Code 5 – Linearization for Channel 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Code 6 – Linearization for Channel 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Code 7 – Linearization for Result of CH1 & CH2 . . . . . . . . . . . . . . . . . . . .13

Linearization Programming Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Application Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Application Example – Manual Setup Mode . . . . . . . . . . . . . . . . . . . . . . .16

Application Example – Auto Setup Mode . . . . . . . . . . . . . . . . . . . . . . . . . .17

Application Example – Manual Setup Mode . . . . . . . . . . . . . . . . . . . . . . .18

Example Programming Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Application Example – Auto Setup Mode . . . . . . . . . . . . . . . . . . . . . . . . . .19

Application Example – Standard Temperature Sensors . . . . . . . . . . . . . . .20

Two-point Calibration Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Configure Linearization Table Settings Procedure for Manual Mode . . . . . .22

Configure Linearization Table Settings Procedure for Auto Mode . . . . . . . .24

Apply a Linearization Table to a Channel Procedure . . . . . . . . . . . . . . . . . .26

Selecting and Calibrating an S Type Thermocouple Procedure . . . . . . . . .27

Contents

The following documents must be read

together with this supplement:

RelevantTiger 320 Series User Manual

The user manual provides general informa-

tion on the relevant Tiger 320 Series meter.

Tiger 320 Series Programming Code Sheet

The programming code sheet provides all

meter programming codes including set-

point programming codes.

List of Figures

Figure 1 – Non-linearized Sensor Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Figure 2 – Linearized Sensor Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Figure 3 – Linearized Sensor Output Showing Flexible Points . . . . . . . . . . . . . . . . . . . . .3

Figure 4 – Setup Modes Flow Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Figure 5 – Programming Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Figure 6 – Linearization Table Date Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Figure 7 – Linearize Yacht Fuel Tank Application Example . . . . . . . . . . . . . . . . . . . . . .15

Figure 8 – Linearization of the Fuel Tank using the Manual Setup Mode . . . . . . . . . . .16

Figure 9 – Linearization using the Auto Setup Mode . . . . . . . . . . . . . . . . . . . . . . . . . . .17

This document is designed to supplement the information described in

the Tiger 320 Series User Manual. It covers the meter’s Linearizing

Functions.

Programming Tip

This document has been written

using a DI-50 7-segment, 5-digit

display meter. When program-

ming meters with other display

options, some display readings

may vary to the diagrams shown.

Note

It is assumed that you are famil-

iar with the Programming

Conventions used throughout

the range of Texmate Tiger 320

Series literature as described in

the user manual.

Texmate Inc.Tel. (760) 598-9899 • www.texmate.comPage 2 •Linearizing Supplement (NZ207)•Linearizing Supplement (NZ207)

PROGRAMMING TIP Symbol

The programming tip symbol is generic to allTiger 320 Series documents

and indicates useful tips when programming the instrument.

The range ofTiger 320 Series supplements contain three graphic symbols to aid you:

WARNING Symbol

The WARNING symbol is generic to all Tiger 320 Series documents and

indicates that if the instruction is not heeded, the action may result in loss

of life or serious injury.

General Notices & Tips

NOTE Symbol

The NOTE symbol is generic to all Tiger 320 Series Operator’s Manual

supplements and indicates important or helpful information on the topic

being discussed.

Definitions The following definitions are relevant to this document:

If an X appears in the description of a 3-digit programming code or in a configuration procedure,

this means that any number displayed in that digit is not relevant to the function being explained,

or more than one choice can be made.

Meter – Controller

The term meter, as used throughout this document, is a generic term for allTiger 320 Series sig-

nal processors and controllers

Texmate, Inc.Tel. (760) 598-9899 • www.texmate.com•Linearizing Supplement (NZ207) Page 3

Linearization Using 32 Flexible Points

Technical Description

Being able to linearize a nonlinear sensor output

with 20 points at fixed intervals has become stan-

dard in most instruments. Unfortunately, some sen-

sor output curves do not follow an even curve line,

resulting in inaccuracies over various areas of the

curve.

Tiger 320 Series meters extend this principal by pro-

viding 32 flexible points.This means that each point

can be individually plotted to suit the most non-linear

sections of the sensor output curve, providing

greater accuracy. See Figure 3.

Figure 3 – Linearized Sensor Output Showing Flexible Points

(Display Reading)

0INPUT

Actual

Reading

Calculated

Reading

LOW

HIGH

(Voltage / Current or

calculated value)

OUTPUT

Figure 2 –Linearized Sensor Output

Actual

Reading

Calculated

Readings

LOW

HIGH

(Display Reading)

INPUT (Voltage / Current or

calculated value)

OUTPUT

Figure 1 –Non-linearized Sensor Output

Output

0Input Signal (mV)

More points along nonlinear areas

36 mV

32 °F

4000 °FPoint 32

Point 1

LOW

HIGH

Tiger 320 Series meters provide up to four independently programmable, flexible 32-point

linearization tables, giving accurate results over the entire scaled range. Each linearization

table can be assigned to more than one channel.

Memory Restrictions

The number of linearizing tables available depends on the amount of memory installed in the

meter. A base meter with 4 kilobits of memory installed has a single table available

(Linearization Table 1). For four tables to be available, the meter requires to have at least 32

kilobits of memory installed.The amount of memory installed in the meter is selected during

ordering to suit the meter’s application.

To overcome this problem, intelligent meters have

been developed that can linearize the sensor output

curve into straight sections.This is done by plotting

points on the curve that relate to known or calculat-

ed values relating to the input signal at that point.

The distance between each point becomes a

straight line and provides a linear output with values

closely relating to the actual curve. See Figure 2.

Conventional meters measuring a nonlinear sensor

output tend to be inaccurate as the intermediate

readings are based on a straight line. Only the low

and high readings are representative of the sensor

output. See Figure 1.

Texmate Inc.Tel. (760) 598-9899 •www.texmate.comPage 4 •Linearizing Supplement (NZ207)

Table 1 Installed Meter Memory and Linearization Tables

Memory TableChannel Selected in

Code 3 [X1X]

Code 4 [XX1]

Code 5 [X1X]

Code 6 [3XX]

Code 7 [X6X]

Remarks

4 kilobits 1

RESULT

With 4 kilobits of memory installed, only Table 1 is

available for CH1, CH2, CH3, CH4 and RESULT.

Code 3 [X1X]

Code 3 [X2X]

Code 3 [X3X]

Code 3 [X4X]

Code 3 [X5X]

Code 4 [XX1]

Code 4 [XX2]

Code 4 [XX3]

Code 4 [XX4]

Code 4 [XX5]

Code 4 [XX6]

Code 5 [3XX]

Code 6 [3XX]

Code 7 [X1X]

Code 7 [X2X]

Code 7 [X3X]

Code 7 [X4X]

Code 7 [X5X]

Code 7 [X6X]

32 kilobits 1

RESULT

125-point

Table select

125-point

Table select

With 32 kilobits of memory installed, Tables 1 to 4

are available for CH1. All four tables can be cascad-

ed to form a 125-point flexible table.

Tables 1 to 4 can be selected from the rear pins of

the meter when one of a selected number of input

modules is installed.The selected table is not avail-

able if CH2, CH3, or CH4 is operating in the analog

output mode. CH1 must be set to Voltage, Current in

Code 2 [X0X].

With 32 kilobits of memory installed, Tables 1 to 4

are available for CH2. All four tables can be cascad-

ed to form a 125-point flexible table.

With 32 kilobits of memory installed, only Table 3 is

available for CH3.

With 32 kilobits of memory installed, only Table 4 is

available for CH4.

With 32 kilobits of memory installed, Tables 1 to 4

are available for RESULT. All four tables can be cas-

caded to form a 125-point flexible table.

Tables 1 to 4 can be selected from the rear pins of

the meter when one of a selected number of input

modules is installed.The selected table is not avail-

able if CH2, CH3, or CH4 is operating in the analog

output mode. CH1 must be set to Voltage, Current in

Code 2 [X0X].

Table 1 lists the linearization tables available for a selected channel when the meter has

either 4 kilobits or at least 32 kilobits of memory installed.It also lists the programming codes

required to be set for selecting a specific table for a specific channel.

LinearizationTable Setup Modes

Linearizing StandardTemperature Sensors

The Tiger 320 Series meter software has been pre-configured with the following standard

thermocouple and RTD linearization tables stored in memory for easy selection. As the

defined reference data for the tables has been pre-configured and stored in the meter, the

relevant table can be selected using standard meter linearization configuration procedures

(See Figure 4):

•Thermocouple types: J / K / R / S / T / B / N.

•RTD 2 / 3 / 4-wire types: Resistance / 385 / 392 / 120 Ω/ Cn 10 Ω.

To configure the meter to use a standard temperature sensor linearization table, see

Application Example – Standard Temperature Sensors on Page 20.

Note:

The rollover feature should not b

cause inaccurate results.

Texmate, Inc.Tel. (760) 598-9899 •www.texmate.com•Linearizing Supplement (NZ207) Page 5

Prog.

SP1 SP2 SP4SP3 SP5 SP6

TEXMATE

•Thermocouple types:

J / K / R / S / T / B / N

•RTD 2 / 3 / 4-wire types:

Resistance / 385 / 392 / 120 Ω/ Cn 10 Ω

Pre-configured

Linearization

Tables Stored

in Meter

Non-preconfigured

Linearization

Tables 1 to 4

AUTO

SETUP

MODE

MANUAL

SETUP

MODE

Use Sensor Output

IP Points

Enter Known or CalculatedValues

OP Points Enter Required DisplayValue

IP Points

OP Points Enter Required DisplayValue

Figure 4 –Setup Modes Flow Diagram

Non-Preconfigured Linearization Tables

Non-preconfigured linearization tables require the linearization table reference data to be

loaded into the selected table in the meter. See Figure 4.

Were the reference data to be loaded is known but not pre-configured into the meter, such

as standard thermocouples, RTDs, and thermistors, it can be entered into the meter using

the manual setup mode.

There are also sensors with no standard reference tables to use as linearization reference

data, such as those sensing the level of vessels and tanks.The sensor output data can be

either calculated and entered into the meter using the manual setup mode, or the sensor

output fed directly into the meter at known stages up to 32 points using the auto setup mode.

Using DifferentTemperature Sensors at the SameTime

The meter can only operate with one non-preconfigured thermocouple linearization table

selected at the same time. Along with a non-preconfigured thermocouple linearization

table, a standard pre-configured thermocouple linearization table can also be selected, but

only if each table is selected for different channels.

LinearizingThermocouples

Thermocouple inputs other than J / K / R / S / T /B / N can be programmed into any chan-

nel, with temperature compensation for ambient changes, from the manufacturers’data

tables in the manual setup mode, or directly from a calibrator using the auto setup mode.

LinearizingThermistors

Thermistor inputs can be programmed into any channel from the manufacturers’data tables

in the manual setup mode, or directly from a calibrator using the auto setup mode.

Linearizing RTDs

RTD inputs other than 385 / 392 / 120 / Cn 10 can be programmed into any channel from

the manufacturers’data tables in the manual setup mode, or directly from a calibrator using

the auto setup mode. Note, 100 Ωand 1000 ΩRTDs have the same linearization table, but

require 100 or 1000 ΩRTD input modules installed in the meter respectively.

Linearization Setup Modes

Tiger 320 Series meters provide three modes to configure a linearization table:

•Auto Setup Mode.

•Manual Setup Mode.

•Initialize Mode.

Auto Setup Mode

The auto setup mode is used when the linearization curve from a sensor output is not known,

but the sensor output can be used to load the reference data into the 32 points of the lin-

earization table.

The auto setup mode allows a sensor input to be directly applied to a linearization table in

the meter over 32 points.The corresponding display reading for each selected point is then

entered into the table.For each selected input, the meter uses the linearization table to store

the sensor input to the meter, known as the input point (IP), and the corresponding display

reading, known as the output point (OP).

This method is usually less accurate than the manual setup mode as the 32 points are normally

programmed into the meter in equal divisions and do not concentrate on the most non-linear areas.

The correct input signal

channel must be selected in

the 3rd digit when configur-

ing a linearization table

using the auto setup mode.

be used with the setpoint reset feature as this could

Texmate Inc.Tel. (760) 598-9899 •www.texmate.comPage 6 •Linearizing Supplement (NZ207)

Calibration

How the channel to be linearized is calibrated directly affects the accuracy of the lineariza-

tion table when it is activated.The two-point calibration mode, using a LOW and HIGH input

source, is normally the simplest and most accurate method of calibrating the input channel.

The input channel should be calibrated over the range of the linearization table’s low and

high input settings.

For example, if calibrating channel 1 to linearize a type 44033 thermistor over the tempera-

ture range –40 °C to 99 °C, the applied LOW input signal would be 75790 ohms, and the

applied HIGH input signal would be 157 ohms (as listed in manufacturers’data tables).

Thermocouples

A K type thermocouple reference is built into the meter and used to initially calibrate the

selected channel prior to calibrating for the selected thermocouple type.

RTDs

A temperature simulator is required to provide a 32 °F reference for a type 385 RTD before

the selected RTD can be calibrated.

Manual Setup Mode

The manual setup mode relies on the points of the linearization curve being known, as with

for example, a type C thermocouple. One of the four linearization tables is selected and the

points of the linearization curve are programmed into the meter.

The manual setup mode allows the points of a sensor’s output curve to be plotted using the

known or calculated values.These values are then manually entered as the input points and

stored in a selected linearization table in the meter. The output points are then entered as

the corresponding display reading for each input point.

This is the most accurate method and reduces the amount of error as the sensor’s output

curve can be accurately calculated and the maximum number of points plotted in the most

nonlinear areas.

Initialize Mode

All four linearization tables are programmed into the meter at the factory with a default

straight line.Selecting the initialize mode [init] re-initializes a reconfigured linearization table

back to the default settings. Select the table to be re-initialised, adding the correct date and

serial number if applicable, and then press the PROGRAM button. Reset CAL to [000].

Linearization Table Input / Output Points

The input (IP) and output (OP) points of the linearization table are displayed as counts on

the display. The position of the decimal point for the selected channel on the display is

selected in the Display Format Mode in Code 1.There are 32 flexible points available on all

four tables.

The output points can be higher or lower than each other.The input points must always begin

from the lowest setting and progress to the highest setting.Each consecutive input point can

be the same as or higher than the preceding output point. The next point cannot be lower

than the preceding point.

Only enter the points required, starting at input point 1 [iP1] / output point 1 [oP1]. If less

than 32 points are required, after the last required point is set press the PROGRAM button

until [End?] appears on the display. This means that all remaining points are set to the last

setting.

Cascading all Four Tables

By cascading all four tables (at least 32 kilobits of memory required), complex curves can be

linearized to 125 points. Cascading each 32 point table means the last point on the first

table must be set to the the same position as the first point on the second table. This

process must be repeated on the second and third, and third and fourth tables until all four

tables are joined.

Texmate, Inc.Tel. (760) 598-9899 •www.texmate.com•Linearizing Supplement (NZ207) Page 7

Pressing the and buttons at the same time enters the Main

Programming Mode.To save a new configuration setting in the Main

Programming Mode and return to the operational display, press the

button once and then press the and buttons at the same time.

The meter’s programming codes are divided into two modes (See Figure 5):

•Main Programming Mode.

•Setpoint Programming Mode.

Each mode is accessible from the operational display.The meter is in the operational display

when it is displaying a processed input signal. All linearization settings are configured in the

main programming mode.

Linearization

Configuration

Programming Codes

To enter press and at the same time

Main Programming Mode

Calibration Modes for Input and Output

Code 1 –Display Configuration

Code 3 –CH1 Post Processing & Serial Mode Functions

Code 4 –CH2 MeasurementTask & Sampling Rate

Code 5 –CH3 Functions

Code 6 –CH4 Functions

Code 7 –Result Processing

[CAL]

[Cod_1]

[Cod_3]

[Cod_4]

[Cod_5]

[Cod_6]

[Cod_7]

Configures all available linearization tables

Configures the display format for the selected channel

to be linearized

Selects a non-preconfigured linearization table for Channel 1

Selects a non-preconfigured linearization table for Result

Display Brightness

[bri]

Adjusts the display brightness.

To enter press and at the same time

Setpoint Programming Mode

The Setpoint Programming Mode

is not required for linearization

table programming.

Enter the Setpoint Programming

Mode menus to adjust SP activa-

tion values and SP control func-

tion settings.

Prog.

SP1 SP2 SP4SP3 SP5 SP6

Operational Display

Prog.

SP1 SP2 SP4SP3 SP5 SP6

Operational Display

Codes 8 and 9 (and

10 if the meter is a

bargraph display ver-

sion) are still avail-

able but are not rele-

vant to linearization

table programming.

To save a new main programming mode con-

figuration setting and return to the operational

display at any point, press the button once.

Then press the and button at the same

time to exit.

Save Code Settings & Exit

Figure 5 –Programming Code List

Code 2 –CH1 MeasurementTask & Sampling Rate

[Cod_2]

Selects a standard pre-configured thermocouple or RTD

linearization table for Channel 1

Selects a standard pre-configured thermocouple or RTD lin-

earization table for Channel 4

Selects a non-preconfigured linearization table for Channel 4

Selects a standard pre-configured thermocouple or RTD lin-

earization table for Channel 3

Selects a non-preconfigured linearization table for Channel 3

Selects a standard pre-configured thermocouple or RTD lin-

earization table for Channel 2

Selects a non-preconfigured linearization table for Channel 2

Texmate Inc.Tel. (760) 598-9899 •www.texmate.comPage 8 •Linearizing Supplement (NZ207)

0 No function

1 On Demand TARE from the PROGRAM button

2 On Demand Single-point Calibration from the

PROGRAM button (requires single input source)

3 On Demand Two-point Calibration from the PRO-

GRAM button (requires dual input source)

4 On Demand Primary Input Compensation Mode

from the PROGRAM button

5 On Demand Manual Loader Mode (no

increase/decrease with HOLD active)

CALIBRATION MODES FOR INPUT AND OUTPUT THIRD DIGIT

0 Result

1 Channel 1

2 Channel 2

3 Channel 3

4 Channel 4

FIRST DIGIT SECOND DIGIT OBJECT FOR 2nd DIGIT

0 Manual Calibration (requires NO input source)

1 Two-point Calibration (requires dual input source)

2 CalibrateThermocouple (requires K type thermo-

couple input source)

3 Calibrate RTD (requires RTD 385 input source)

4 Calibrate Smart Input Module.Note:This function

is not available on all input modules

5 Calibrate Analog Output mA/V Output Signal

(requires multimeter connected to pins 16 and 17)

0 Serial Communications Properties

1 Set Auto Zero Maintenance for 3rd digit

2 Set Averaging Samples & Averaging Window for

3rd digit

3 Totalizer Settings Mode

4 Setup 32-point Linearization Tables

5 Scale Analog Output LOW/HIGH (zero/span)

Display Readings

0 Functions

Activated

by Pressing

the PRO-

GRAM

Button

1 Calibration

Procedures

2 Related

Calibration

Functions

Use buttons to

select the required lin-

earization setup mode

PPP

Use buttons to select the

date: 1st two digits = YEAR, 2nd two

digits = WEEK

Use buttons to select

the serial number from 0 to

65535 Use buttons to enter

input point number 1

Use buttons to select the lin-

earization table number from 1 to 4

Use buttons to enter

output point number 1

Use buttons to enter

input point number 32 Use buttons to enter

output point number 32

LinearizationTable Settings

The Calibration Mode [CAL] [24X] is where all available linearization table settings are con-

figured. Setting the 1st digit to 2selects Related Calibration Functions.Setting the 2nd digit

to 4selects the Setup 32-point Linearization Tables mode.The 3rd digit selects the channel

the linearization table is applied to. When configuring a linearization table in the auto mode,

the correct input channel must be selected to ensure the input signal from the sensor is

applied to the linearization table input points.

On entering the Setup 32-point Linearization Tables mode, configure the following settings:

•Select one of the three setup modes to configure the linearization tables.

•Select the table number.

•Set the date and serial number for the selected table.

•Configure the input and output points for the selected linearization table.

Setup Modes

For details on the manual, auto, and initialize setup modes, see Linearization Setup Modes

on Page 5.

Linearization Table Identity

As a reference, the table number, the date, and a serial number can be entered before the

linearization points in either the auto or manual setup mode.

Table Number

If the meter has the four table memory option, any table from 1 to 4 can be selected for con-

figuration.

Figure 6 –Linearization Table Date Setup

Date

A date displaying the year and week the linearization table

was configured can be added to each table. See Figure 6.

WEEK

YEAR

Serial Number

A serial number using up to five digits from 0 to 65535 can be set for each table.

Set input and output

points 2 to 31 as required

Note:

The input channel setting in

the 3rd digit is not relevant to

the manual setup mode.

Note:

The correct input signal channel must be

selectedin the 3rd digit when configuring alin-

earization table using the auto setup mode.

Texmate, Inc.Tel. (760) 598-9899 •www.texmate.com•Linearizing Supplement (NZ207) Page 9

[rESLt]

[Ch1]

[Ch2] [Ch3] [Ch4] [tot_1] [tot_2]

[PEAK]

[1 to 244]

[tArE]

[VALEY]

[diSP]

FRONT PANEL ANNUNCIATORS

0 ON when Setpoints are ON (relay

energized)

1 ON when Setpoints are OFF (relay

de-energized)

2 Always OFF. See Note 1

3 LED SP1 ON indicates RISING sig-

nal trend.

LED SP2 ON indicates FALLING

signal trend.

DATA DISPLAY SOURCE

0 Normal Display Mode (i.e. operational dis-

play shows selected register) updates

every 0.5 seconds

1 Manual Loader Mode (Direct Display).

2 Update at sample rate selected in Code 2

5 Select data source as per 3rd digit

6 Select display format as per 3rd digit

7 Select text character as per 3rd digit

SELECT DATA SOURCE FOR

0 Primary Display

1 Second Display. See Note 2

2 Third Display. See Note 2

3 Peak/Valley

4 Analog Output 1

5 Analog Output 2 (under development)

6 Totalizer 1

7 Totalizer 2

CODE 1 –DISPLAY CONFIGURATION: SELECT DATA SOURCE FOR SELECTED CHANNEL

FIRST DIGIT SECOND DIGIT THIRD DIGIT

See diagram below

Select Data Source

Select Display Format

Select Text Character

Use the and but-

tons to cycle through the

options

Select Data Source

Use the and but-

tons to select a register

as the data source

See diagram below

See diagram o below

Note 1:

LED annunciators are always off, except when the meter is in single chan-

nel VOLTAGE or CURRENT mode and Code 3 = [X6X], or Code 7 = [X6X]

in which case the LEDs indicate which 32-point table has been selected from

the rear pins (SP1 = Table 1, SP2 = Table 2, SP3 =Table 3, SP4 = Table 4).

Note 2:

These options are only for use with meters that have more than one dis-

play.With bargraph meters the PRIMARY display is the digital display, and

the SECONDARY display is the bargraph display.

LAST DIGIT ROUNDING

0 No rounding

1 Rounding by 2’s

2 Rounding by 5’s

3 Rounding by 10’s

DISPLAY UNITS

0 Decimal

1 24-hour clock mode

Hours: Minutes:

Seconds (6-digit ver-

sion only)

2 12-hour clock mode

(12:30 am is displayed

as 12:30A. 12:30 pm is

displayed as 12:30P)

3 24-hour clock mode

Days: Hours:Minutes

(6-digit version only)

7 Octal

DECIMAL POINT PLACEMENT

0 No decimal point

1 XX.XX.XX (6-digit version only)

2 X.XXXXX (6-digit version only)

3 X.XXXX

4 X.XXX

5 X.XX

6 X.X

7 Decimal Point set from the rear

(X.XXXXX to XXXXXX). See Note 3.

Also See Note 4

Display Format Mode

FIRST DIGIT SECOND DIGIT THIRD DIGIT

Program the three digits to the required display format

mode

Note 3:

These functions are only available on selected input modules.

Note 4:

If Code 1's display modes have been entered (second digit set to 5, 6, or 7), the display

will cycle between Code 1 and the display functions mode each time the PROGRAM but-

ton is pressed.To leave the cycle, the Code 1 digits must be reset to any relevant func-

tion between [X00] to [X20].This takes you into Code 2.

Note:

Selecting 1, 2, or 3

in the 2nd digit of

this mode config-

ures the display of

the selected chan-

nel as a clock.

Use the UP/

DOWN buttons

to cycle through

the menu

Select Last Digit Text Character

Press the UP

button 4 times

as the next 4

characters are

blank

Code 1 –Configuration Settings

Before configuring the meter for a linearization application, configure the display settings for

the required channel in Code 1:

•Setpoint Annunciators.

•Display Update Rate.

•Select Data Source (for selected channel to be linearized).

•Set Display Format (last digit rounding, display units, and decimal point placement).

•Select last digit text character.

Note 5:

If only 4 kilobits of memory is installed, only Table 1 is available for:

• CH1 in Code 3, 2nd digit.

• CH2 in Code 4, 3rd digit.

• CH3 in Code 5, 1st digit.

• CH4 in Code 6, 1st digit.

• RESULT in Code 7, 2nd digit.

Texmate Inc.Tel. (760) 598-9899 •www.texmate.comPage 10 •Linearizing Supplement (NZ207)•Linearizing Supplement (NZ207)

Code 2 –StandardThermocouple or RTD Linearization for CH1

To apply a standard thermocouple or RTD (pre-configured) linearization table to Channel 1, select

the required table from the 2nd and 3rd digits in Code 2.

FOR VOLTAGE

0 No function

1 Peak detector

2 Pressure with Auto-cal

FOR THERMOCOUPLE

0 Type J

1 Type K

2 Type R

3 Type S

4 Type T

5 Type B

6 Type N

7 Select user defined table set up in CAL [24X]

FOR RTDTYPE (2-, 3-, 4- WIRE)

0 Resistance

1 RTD 385

2 RTD 392

3 RTD 120

4 Cn 10

FREQUENCY RANGE SELECTION

0 99.999 Hz range from 0.010 Hz

1 99.999 Hz range from 2.000 Hz

2 999.99 Hz range from 0.01 Hz

3 999.99 Hz range from 2.00 Hz

4 9999.9 Hz range from 0.1 Hz

5 9999.9 kHz range from 2.0 Hz

6 99 kHz range from 1 Hz (1 s gate)

7 655.35 kHz range from 10 Hz (0.1 s gate)

PERIOD MEASUREMENT SELECTION

0 99.999 s

1 9.9999 s

2 999.99 ms

3 99.999 ms

COUNTER/RESIDENTTIMER/CLOCK SELECTION

0 Counter input with 16 bit Pre-scaler

1 Setting of 16-bit Pre-scaler

2 Debounced Counter with Pre-scaler

3 Up/Down Counter with Pre-scaler

4 0.1 sec Timer with Pre-scaler

5–

6 External 24-hour clock

7 Internal 24-hour clock

ANALOG SAMPLE RATE

0 Sample Rate:Typically 10 samples/second (60 Hz)

Control Output Rate: 0.1 seconds

See Example

1 Sample Rate: Typically 10 samples/second (50 Hz).

Control Output Rate: 0.1 seconds

See Example

2 Sample Rate: Typically 10 samples/second (60 Hz)

Counter or 10 millisecs Control Output Rate

See Example

3 Sample Rate: Typically 10 samples/second (50 Hz)

Counter or 10 millisecs Control Output Rate

See Example

Note:

Output Rate refers to setpoint and macro outputs,

and input rates from smart input modules.

Note:

All above sample rates are quoted for single channel

operation. Where more than one channel is avail-

able, sample rates are divided by the number of

active channels.See Example.

MEASUREMENT TASK

0 Voltage, Current

1 TC (3rd digit selects type of TC)

2 RTD 3-wire (3rd digit selects type of RTD)

3 RTD 2- or 4-wire (3rd digit selects type of RTD)

4 Frequency

5Period

6 Counter

7 Smart Input Module

CODE 2 –CHANNEL 1 MEASUREMENT TASK AND SAMPLING RATE

SMART INPUT MODULE

0 Output Register 1

1 Output Register 2

2 Output Register 3

3 Output Register 4

4 Output Register 5

5 Output Register 6

6 Output Register 7

7 Smart Input Module Setup. See Note 7.

THIRD DIGIT

FIRST DIGIT SECOND DIGIT

1 Channel = 10 samples/second

2 Channels = 5 samples/second

3 Channels = 3.33 samples/second

4 Channels = 2.5 samples/second

Example: 10 Samples/Second

Note 7:

Only available with

selected input modules.

1 = 0.1 second

10 = 1 second

600 = 1 minute

3600 = 1 Hour

X61 Sets Prescaler

Use

buttons to set

prescale values

Other manuals for Tiger 320 Series

Table of contents

Other Texmate Measuring Instrument manuals

Texmate

Texmate DL-40US-DCA User manual

Texmate

Texmate DL-40JANUS-SG User manual

Texmate

Texmate UM-35-CL User manual

Texmate

Texmate Tiger 320 Series Operating instructions

Texmate

Texmate DI-45U TIGER CUB User manual

Texmate

Texmate FL-B101Q-HZ User manual

Texmate

Texmate FL-B101D40H User manual

Texmate

Texmate DL-40 User manual

Texmate

Texmate LYNX FX-B101Q-DCA User manual

Texmate

Texmate DL-40PSF-DCA User manual

Texmate

Texmate Leopard Series User manual

Texmate

Texmate DL-40JANUS-PROCESS User manual

Texmate

Texmate CL-B101D40RPM User manual

Texmate

Texmate DI-60AE User manual

Texmate

Texmate SM-35 User manual

Texmate

Texmate UM-35-SG User manual

Texmate

Texmate Leopard Series User manual

Texmate

Texmate PM-35U User manual

Texmate

Texmate DL-40PSF-PROCESS User manual

Texmate

Texmate Leopard Series User manual

Texmate

Texmate UM-40-ACV User manual

Texmate

Texmate DX-35-XX-PS1 Instruction sheet

Texmate

Texmate BL-40PSF-PROCESS User manual

Texmate

Texmate FL-B101Q-DCA User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual