Texas Instruments TMS320C2000 User manual

TMS320C2000 AC/DC Developer’s Kit Overview

Quick Start Guide

Literature Number: SPRUFR8September 2008

Trademarks

Quick Start GuideSPRUFR8 – September 2008

TMS320C2000™ AC/DC Developer’s Kit Overview

This document describes the ac/dc developer’s kit evaluation board designed to work with TexasInstruments C2000™ DSP platform devices. This kit is a part of the digital power tools package from TI,designed to give customers an opportunity to quickly evaluate C2000 products for power conversionapplications at a safe input voltage and power level.

WARNINGThis equipment may generate voltages and currents that can beinjurious to humans, and must be used with extreme caution. Theuser must employ appropriate safeguards to avoid serious injury.

TMS320C2000, C2000, Code Composer Studio are trademarks of Texas Instruments.

Blackhawk is a trademark of EWA Technologies, Inc.

All other trademarks are the property of their respective owners.

2TMS320C2000™ AC/DC Developer’s Kit Overview SPRUFR8 – September 2008Submit Documentation Feedback

1 Features

2 Hardware Overview

Phase

Shifted

Full Bridge

Isolation

3-V - 12-V

DC O/P

C2000 JTAG

11-33 Vrms

AC I/P

2-Phase

Interleaved

PFC Section

48-V DC

PFC O/P 12-V, 5-V, 3-V

Bias Supply RS232

48-V DC

FB I/P

www.ti.com

Features

The ac/dc developer’s kit contains a motherboard which accepts any of the plug-in controlCARDs. Theboard is divided into a power factor correction (PFC) section and an isolated dc-dc conversion full bridge(FB) section. Features of the ac/dc developer’s kit include:•Voltage and current measurements via ADC•Over-current and over-voltage protection on the PFC side and over-current protection on the FB sidevia trip zone ( TZ) pins•Closed loop digital control with feedback using 28x on-chip ePWM and ADC•UART communications header available for host control•A learning platform allowing the user to easily probe the most significant wave forms within a boardthat is laid out conservatively and contains many test points.•An analog and a digital header to provide easy interconnection with the EZDSP board if desired.•Host GUI, a friendly way to control / demo the application, based on open source C# freeware•Special hardware circuit allows experimentation with peak-current-mode control operation, if desired•Hardware Developer’s Package is available and includes schematics, bill of materials, Gerberfiles, …etc

The PFC section accepts an ac input of 11 – 33 Vrms, while the FB section accepts a 48-V dc input.Figure 1 shows the acdc board identifying the key components.

Figure 1. Components

SPRUFR8 – September 2008 TMS320C2000™ AC/DC Developer’s Kit Overview 3Submit Documentation Feedback

2.1 Hardware Set Up

Hardware Overview

www.ti.com

Auxiliary Supply A 12-V auxiliary supply connection at J9 to power the control and drive circuit.Optional 5-V supply connection at J10 to only power the control circuit3.3-V ISO Supply A 3.3-V isolated supply is generated on-board for serial communication. See theHardware Setup section of this document.PFC section Two-phase interleaved boost power stage for power factor correction11 – 33 Vrms ac ac input for the PFC section at connector J13-J14I/P

FB section Phase shifted full bridge power stage for dc-dc conversion48-V dc I/P dc input for the FB section at connector J26-J27Boot Jumpers Controls how the F280x boots. (J31)If no jumpers are placed, the target boots from flash.If a jumper is placed at 84, the target boots from the SCI.

To be able to run the various software builds for the projects included in this package a 12-V dc regulatedbench power supply, an isolated 11-33 Vrms ac power supply, a 48-V dc power supply, a bank ofappropriately rated resistive loads and an emulator are required apart from the hardware included in thispackage (suggested emulators are listed near the end of this document).

CAUTION

Do not connect 110-V or 220-V main supply to the ac input on the ACDCboard. It is designed to handle a low voltage ac input, and the connectionconfiguration must ensure this. If voltages exceeding 33 V ac are applied to thePFC section or voltages exceeding 50 V dc are applied to the FB section, theboard can be damaged.

The application-specific motherboard provided in this kit can be used in one of two ways:1. Test Drive – Using the provided GUI application, you do not require Code Composer Studio™ oremulation tools. This provides a great way to run or demo the application code quickly and see whatfunctionality the hardware offers. Note: exactly the same functionality can be achieved by using theCode Composer Studio Watch Window and graphing features during emulation in the second mode.2. Code Composer Studio Software Development Platform – With the project code provided, theapplication can be modified, compiled, loaded and run in a development environment. Code ComposerStudio and emulation hardware tools are required for this.

Note: By default, the V

is connected to VDD_ISO (isolated supply for serial communications) onthe controlCARD through resistor R13. Similarly GND and GND_ISO are connected togetherusing resistor R16. Therefore if a non-isolated input ac supply is used, replace R16 on thecontrolCARD with around 2200pF capacitor and also remove resistor R13. If emulation isdesired in this case, you must use an isolated emulator.

Follow these steps to set up the hardware for either the GUI or software development platform:Step 1. Unpack the DIMM style controlCARD.Step 2. Spread open the winged retaining clips on controlCARD U23 connector.Step 3. Sit the DIMM card loosely in the connector slot. Make sure to align the two keyed notchesand position the card bottom corners inside the retaining clips (see Figure 2 )Step 4. Push vertically down using even pressure from both ends of the card until the clips snap andlock. (To remove or eject the card, spread open the retaining clips with thumbs.)

4TMS320C2000™ AC/DC Developer’s Kit Overview SPRUFR8 – September 2008Submit Documentation Feedback

2.2 Test Drive With GUI – (skip this if you need only emulation support)

Pin 4

of J18

www.ti.com

Hardware Overview

Figure 2. Connecting the DIMM Card

Step 1. Plug in the serial cable provided to connector J18 making sure the red wire aligns with the pin4 of J18 (marked in Figure 3 ) on EVM (or use a DB9 serial cable at J21).Step 2. Insert a jumper in position 84 on Boot pins.Step 3. Insert a jumper between pins 1 and 2 of J19.Step 4. Similarly insert a jumper between pins 3 and 4 of J19.Step 5. Plug the DB9 connector into your PC using either a serial port or a serial-to-USB converterdongle.Step 6. Connect the PFC output at J24-J25 to the FB input at J26-J27 using appropriate wires. Makesure to match the PFC output and FB input polarity.Step 7. Apply a resistive load to the phase shifted full bridge system at connector J28-J29. Choosethe value of the resistors and their power rating to present a load of about 10 W-30 W at 6 V.Step 8. See Software Setup GUI-TestDrive

Figure 3. Pin 4 Location

Note: If you are not using an isolated ac supply, you must replace R16 on the controlCARD witharound 2200 pF capacitor. You also need to remove resistor R13 on the controlCARD. Ifemulation is desired in this case, you must use an isolated emulator.

SPRUFR8 – September 2008 TMS320C2000™ AC/DC Developer’s Kit Overview 5Submit Documentation Feedback

2.3 Code Composer Studio Software Development Platform emulation - additional steps

3 Software Set Up

Software Set Up

www.ti.com

1. Connect the JTAG emulator cable to connector J20.2. See Software Set-up Code Composer Studio - Development.

For full details (schematics, pin-out table, etc) of the hardware, see the Hardware Developer’s Package,ACDC-HWdevPkg. See Section 3 for download location.

The ac/dc kit application software example, GUI, step-by-step lab style documentation, and other usefulsoft collateral is available on the TI website. If you already have your own software project and do notrequire this collateral, skip this section. As explained in the hardware set up section, the target motherboard can be run either with the GUI or Code Composer Studio. The GUI executable file is found as partof the main software download. Follow the steps below for either case.

To run any of the application-specific software in Code Composer Studio, first install the baseline codethat contains the header files, libraries, etc. If you already have the base-line software installed, skip thebaseline install steps and go to the acdc Kit section.

To download the free TI soft collateral follow these steps:Step 1. Baseline soft collateral and hardware documents (skip this if you already have this softwareinstalled)

a. On an Internet browser type: http://www.ti.com/f28xkitsb. At the C2000 collateral page, choose the ACDC Developer’s Kit download link.c. When prompted, fill in the TI customer registration details and click ok.d. Save the .zip file to the directory of your choicee. Unzip the file and run the install program baseline software set up.f. The installer creates the following default directories:

C:\TI_F28xxx_SysSW

~Docs

~GeneralPurposeGUI

~HexConverterUtility

~SupportFiles

FlashingLeds

C:\TI_F28xxx_SysHW

CC280xxHWdevPkg

CC2833xHWdevPkg

DockingStnHWdevPkg

6TMS320C2000™ AC/DC Developer’s Kit Overview SPRUFR8 – September 2008Submit Documentation Feedback

4 Running the Application

5 Emulators

www.ti.com

Running the Application

2. ACDC Kit soft collateral and hardware documentsa. On an Internet browser type: http://www.ti.com/f28xkitsb. Choose the ACDC Kit linkc. When prompted, fill in the TI customer registration details and click okd. Save the .zip file to the directory of your choicee. Unzip the file and run the install program acdc software set up1. The installer creates the following default directories:

C:\TI_F28xxx_SysSW

~SupportFiles

lib

PowerLibPFC2PHIL

~Docs

~GUIFBPS

~Docs

~GUIACDC

~Docs

~GUIC:\TI_F28xxx_SysHW

ACDC-HWdevPkg

To run the application specific hardware, choose either “TestDrive-GUI” or “CCS-Development” optionsbelow and follow the appropriate steps.Step 1. TestDrive-GUI

a. Open the GUI Quick Start Guide, QSG-ACDC-GUI.pdf, found in:C:\TI_F28xxx_SysSW\ACDC\~Docs\

b. Browse to the directory: C:\TI_F28xxx_SysSW\ACDC\~GUI

c. Open ACDC-GUI.exe

d. Follow the step-by-step instructions found in the Quick Start GuideStep 2. Code Composer Studio - Developmenta. If you have emulation tools and Code Composer Studio already installed and active, loadthe project file PFC2PHIL.pjt in: C:\TI_F28xxx_SysSW\PFC2PHIL\ or FBPS.pjt in:C:\TI_F28xxx_SysSW\FBPS\ or ACDC.pjt in: C:\TI_F28xxx_SysSW\ACDC\b. See the corresponding (PFC2PHIL.pdf/FBPS.pdf/ACDC.pdf) user guide for a step-by-stepwalk through of how to compile and run the various labs. This document is in thecorresponding documents folder for the project(\~Docs\).

The following companies provide low cost, full-featured emulators designed specifically for C2000controllers:

•Blackhawk™

– USB2000 Controller (orderable through TI as part number TMDSEMU2000U)

SPRUFR8 – September 2008 TMS320C2000™ AC/DC Developer’s Kit Overview 7Submit Documentation Feedback

6 References

References

www.ti.com

–http://www.ti.com

– $299•Spectrum Digital– XDS510LC JTAG Emulator (part number 701902)–ttp://www.spectrumdigital.com

– $249

For more information, see the following guides:•PFC2PHIL – provides detailed information on the PFC2PHIL project within an easy to use lab-styleformat.

C:\TI_28xxx_SysSW\ PFC2PHIL\~Docs\ PFC2PHIL.pdf•FBPS – provides detailed information on the FBPS (phase shifted full bridge) project within an easy touse lab-style format.C:\TI_28xxx_SysSW\ FBPS\~Docs\ FBPS.pdf•ACDC – provides detailed information on the ACDC (PFC + FB) projectC:\TI_28xxx_SysSW\ ACDC \~Docs\ ACDC.pdf•QSG-ACDC-GUI – gives an overview on how to quickly demo the ACDC project using an intuitive GUIinterface.

C:\TI_28xxx_SysSW\ACDC\~Docs\QSG-ACDC-GUI.pdf

•ACDC-HWdevPkg – a folder containing various files related to the hardware on the ACDC Kit board(schematics, bill of materials, Gerber files, PCB layout, etc).C:\TI_28xxx_SysHW\ACDC-HWdevPkg\

•System Framework Overview Guide – presents more information on the system framework found inF28xxx EVM projectsC:\TI_28xxx_SysSW\~Docs\SystemFrameworkOverview.pdf

•F28xxx User’s Guideshttp://www.ti.com/f28xuserguides

TMS320C2000™ AC/DC Developer’s Kit Overview8 SPRUFR8 – September 2008Submit Documentation Feedback

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers shouldobtain the latest relevant information before placing orders and should verify that such information is current and complete. All products aresold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standardwarranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except wheremandated by government requirements, testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products andapplications using TI components. To minimize the risks associated with customer products and applications, customers should provideadequate design and operating safeguards.TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Informationpublished by TI regarding third-party products or services does not constitute a license from TI to use such products or services or awarranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectualproperty of the third party, or a license from TI under the patents or other intellectual property of TI.Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompaniedby all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptivebusiness practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additionalrestrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids allexpress and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is notresponsible or liable for any such statements.TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonablybe expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governingsuch use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, andacknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their productsand any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may beprovided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products insuch safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products arespecifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet militaryspecifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely atthe Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products aredesignated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designatedproducts in automotive applications, TI will not be responsible for any failure to meet such requirements.Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAmplifiers amplifier.ti.com Audio www.ti.com/audioData Converters dataconverter.ti.com Automotive www.ti.com/automotiveDSP dsp.ti.com Broadband www.ti.com/broadbandClocks and Timers www.ti.com/clocks Digital Control www.ti.com/digitalcontrolInterface interface.ti.com Medical www.ti.com/medicalLogic logic.ti.com Military www.ti.com/militaryPower Mgmt power.ti.com Optical Networking www.ti.com/opticalnetworkMicrocontrollers microcontroller.ti.com Security www.ti.com/securityRFID www.ti-rfid.com Telephony www.ti.com/telephonyRF/IF and ZigBee® Solutions www.ti.com/lprf Video & Imaging www.ti.com/videoWireless www.ti.com/wireless

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Texas Instruments:

TMDSACDCKIT

Other manuals for TMS320C2000

Table of contents

Other Texas Instruments Controllers manuals

Texas Instruments

Texas Instruments bq78350-R1 Use and care manual

Texas Instruments

Texas Instruments TPS51124 User manual

Texas Instruments

Texas Instruments TMS320x281 series User manual

Texas Instruments

Texas Instruments TMS320C6000 DSP User manual

Texas Instruments

Texas Instruments UCC14240EVM-052 User manual

Texas Instruments

Texas Instruments bq24013 User manual

Texas Instruments

Texas Instruments LM5160A User manual

Texas Instruments

Texas Instruments TUSB422 EVM User manual

Texas Instruments

Texas Instruments MSMC User manual

Texas Instruments

Texas Instruments LM10524EVM User manual

Texas Instruments

Texas Instruments bq24010/2 User manual

Texas Instruments

Texas Instruments TPS70351EVM User manual

Texas Instruments

Texas Instruments bq24133EVM User manual

Texas Instruments

Texas Instruments TMS320C674X User manual

Texas Instruments

Texas Instruments Stellaris MDL-BDC24 User manual

Texas Instruments

Texas Instruments bq34z100 User manual

Texas Instruments

Texas Instruments TMS320C2000 User manual

Texas Instruments

Texas Instruments DRV2511Q1EVM User manual

Texas Instruments

Texas Instruments OMAP5910 User manual

Texas Instruments

Texas Instruments TPS2151 User manual

Texas Instruments

Texas Instruments TPS59640EVM-751 User manual

Texas Instruments

Texas Instruments TSB12LV26 Installation and user guide

Texas Instruments

Texas Instruments AM335 Series User manual

Texas Instruments

Texas Instruments TMS320C6000 DSP User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual