Tendring Pacific Dansensor CheckMate 3 Operating manual
Preventative Maintenance Guide
Dansensor CheckMate 3 (EC)
Technical Support: 01223 492087
Dansensor Preventative Maintenance Guides help you to care more effectively for your equipment
during the time between planned services.
For Safety Instructions, Trouble Shooting & Operation - please refer to the User Guide.
Cleaning and Maintenance
In addition to the Annual Service & Calibration, it is recommended to carry out the following
maintenance checks at the interval times stated below.
To order consumables please contact Ann Walker on
01223 495484 or email [email protected]
Every Day:
Water Trap Filter and Needle - Check and Replace (as required)
Once a Week:
Sample Hose – Check and Replace (as required)
During use of the device, dust, debris, and moisture may be
sucked through the measuring system.
1.The water trap filter will therefore have to be replaced
regularly depending on the environment in which the device is
used.
2. The needle may sometimes touch the product being
measured, or the needle may suck fluid from the packaging
from which the measurement is taken. If this happens, it will be
necessary to replace both the needle and the filter.
3. If there is any dirt or fluid in the sample hose it should be
replaced or cleaned using dry compressed air.
To see the calibration menu, log into Access level as a
supervisor. The standard supervisor passcode is ‘0000’. Once
in the main menu, (Screen 1), use the down arrow key to scroll
to the calibration menu. Push the right arrow key to enter.
The appearing calibration menu (Screen 2) holds a list of the
various sensors in the device. For each sensor there is a table
showing the appropriate calibration parameters. To proceed
with the calibration, push the right arrow key.
From the next menu (Screen 3), select between the following
items: ‘Perform calibration’ or ‘Erase/enter calibration’. Select
‘Perform calibration’ using the circle enter key.
Use the up, or down arrow key to select the calibration value
fields for the O sensor (EC), then push the circle enter key.
Screen 1 Screen 2
Screen 3 Screen 4
Daily Air Calibrations- Daily offset (20.9% O) calibrations can be performed on the CheckMate 3 (EC) version.
For more information please contact Technical Support. NOTE: ONLY APPLIES TO EC SENSOR VERSIONS.
Preventative Maintenance Guide
Dansensor CheckMate 3 (EC)
Technical Support: 01223 492087
Dansensor Preventative Maintenance Guides help you to care more effectively for your equipment
during the time between planned services.
For Safety Instructions, Trouble Shooting & Operation - please refer to the User Guide.
To order consumables please contact Ann Walker on
01223 495484 or email [email protected]
The pump starts and now make sure to expose the needle to
20.9 atmospheric air. Let the measurement run for
approximately five minutes. Select the 20.9460 gas entry from
the list and push the circle enter key. (Screen 5)
Next you will be asked to perform the calibration. The existing
calibration value will be overwritten. Select ‘Yes’ then push the
circle enter key. (Screen 6)
The next screen (Screen 7) shows that the calibration is being
executed. When the calibration has finished, the pump stops
and the display returns to the sensor menu. (Screen 8).
Note that the fields for the 20.9460% gas has now been
updated with the values obtained during calibration. The
O sensor (EC) has now been calibrated.
To return to the measuring screen, press the back arrow four
times.
Daily Air Calibrations- Daily offset (20.9% O) calibrations can be performed on the CheckMate 3(EC) version.
For more information please contact Technical Support. NOTE: ONLY APPLIES TO EC SENSOR VERSIONS.
Screen 5 Screen 6
Screen 7 Screen 8
Consumables Kit Part No: 300436
3 x Septum, 15mm grey soft (1000pcs)
5 x Needle kit 0.8mm (10pcs)
1 x Hose, sample gas (5pcs)
1 x Filter water trap (10pcs)
1 x Sampling kit standard
Printer Paper, 57mmx25mm (box 20) Part No: 220076
Hose, sample gas (5pcs) Part No: 310677
Filter water trap kit (10pcs) Part No: 310335
Filter water trap kit (100pcs) Part No: 310339
Needle kit (10pcs) Part No: 220078
Needle kit (100pcs) Part No: 280204
Needle Pen (10pcs) Part No: 310781
Septums, grey (1000pcs) Part No: 310337
Septums, grey (10000pcs) Part No: 220157
Sampling kit standard Part No: 300437
Dansensor CheckMate 3 (EC) Consumable Parts
Table of contents
Other Tendring Pacific Measuring Instrument manuals
