access the calibration activation switch. Connect the supplied AC adapter
to the back of the sensor or ensure new batteries are installed.
2. Power up the sensor and wait for the Warm-up to end.
3. Next verify the Elevation correction has been set. Refer to the steps in
Elevation Correction for procedure.
4. If you are calibrating to ambient conditions make sure the sensor is
displaying a stable reading - avoid breathing in the area of the monitor.
If you are flowing gas to the calibration port of the sensor, allow the
gas to flow for at least 10 minutes before initiating calibration.
5. Press the Mode button twice. The Calibration mode will begin blinking.
5. Press Enter.
6. Use the Up/Down button to adjust reading to the current ambient
conditions or concentration of the gas being used. Pressing the button
once will change the readings in increments of 10 ppm. To increase
the speed, press and hold the button.
NOTE - For best accuracy, a reference or known concentration of CO2
should be used when adjusting the reading. Bottled nitrogen can be used
to provide a zero concentration gas.
7. Next, on the backside of the unit locate the push button switch (under
the battery cover, in the small round hole to the right of the connector
jack), use a small pointed object to depress and hold the switch for 5
seconds. CALIBRATION will begin to blink.
8. Press Enter.
9. Calibration In Progress will begin to blink. At this point the unit will
program itself based on the CO2value that was input in Step 6. The
calibration process will take approximately 5 minutes.
When Calibration is complete, the display will return to the steady
Calibration mode. Press Enter to return to the normal operation mode.
Temperature Adjustment
Use this procedure to adjust the temperature output when you wish to
have the temperature output match a reference sensor. The accuracy of
a field adjustment is dependent upon the stability of the environment is
which the procedure is performed, and upon the accuracy of the refer-
ence sensor.
1. Connect the supplied AC adapter to the back of the sensor. If you do
not have the AC adapter, new batteries should be used.
2. Power up the sensor and place in a stable environment, free of drafts
or temperature changes. Wait 30 minutes for the unit to fully equili-
brate with the environment. Do not hold the unit in your hand during
this period. Press the mode button until the blinking word TEMPERA-
TURE appears.
4. Press Enter. Both the word TEMPERATURE and the numeric
temperature display will begin blinking in unison.
5. Use the Up/Down button to adjust the temperature reading to match
the reference.
6. Press Enter. The temperature offset is immediately adjusted, the
blinking stops, and the unit is now in normal operating mode.
Accessories
CO2View™ Real-Time Graphing/Calibration Software 2080
Allows the 7001 to log directly to a Windows™ compatible PC and graph
concentrations in real time (includes RS232 cable). Includes an interface
that allows the user to perform a zero and span calibration on the sensor.
Hobo® Data-Logger Kit CO2 – Temp & RH 2077
Small data-logger that mounts to the back of the 7001. Records CO2,
Temp, and Relative Humidity. Stores over 7900 data points and samples
at a user adjustable time interval. Graphing software included.
2070 Datalogging Cable
Connects the 7001 to 3rd party devices. Includes two leads for the CO2
and temperature ouputs.
Calibration Kit 2075
Comes with necessary equipment to perform zero calibration.
Specifications
Method
Dual Beam Absorption Infrared™
Display - LCD
Independent CO2 and Temperature readings.
Calculates and Displays Ventilation Rates
Sample Method
Diffusion or flow through (50 - 100 ml/min)
Performance - CO2 Channel
Measurement Range
0-10,000 ppm display
0-4,000 ppm voltage output
Display Resolution
± 1 ppm
Accuracy
±50 ppm or ±5% of reading up to 5,000 PPM (Above 5,000 PPM not
specified)
Repeatability
±20 ppm
Temperature Dependence
±0.1% of reading per °C or ±2 ppm per °C, whichever is greater, refer-
enced to 25°C
Pressure Dependence:
0.13% of reading per mm Hg (Corrected via user input for elevation)
Response Time
<60 seconds for 90% of step change
Warm-Up Time
<60 seconds at 22°C
Calibration Interval
12 months, offset adjustment using single gas at 0-1000 ppm CO2. Full
factory calibration available
Performance - Temperature Channel
Temperature Range
Voltage output 32 to 104°F (0 to 40°C)
Display 32 to 122°F (0 to 50°C)
Display Resolution
0.1°F (0.1°C)
Display Options
°F, °C, or Off. Set with panel button.
Accuracy
±2°F (±1°C)
Response Time
20-30 minutes (case must equilibrate with environment)
Calibration Interval
12 months, offset adjustment using temperature standard at 50 to 86°F
(10 to 30°C). Full factory calibration available
Outputs
(Analog) CO2
0-4 VDC, 1mV/ppm (4,000 ppm max)
Temperature
0-4 VDC linear, 32-104°F (0-40°C)
Output Impedance
100 Ohms
(Digital)
RS232 for use with Telaire® CO2View™ Graphing Software
(Wiring Connection)
One RJ-45 Connector
Dual Analog output plus digital output
Power Supply
Battery Type
Four AA batteries, not included
Battery Operation
80 hours (alkaline)
External
6 VDC from external AC/DC adapter, included
Power Requirements
100 mA Peak, 20 mA average from 6V
General
Operating Conditions
32-122°F (0-50°C)
0-95% RH, non-condensing
Storage Temperatures
-4 to 140°F (-20 to 60°C)
Certifications
FCC Class 15 Part B
CE
Warranty
18 months parts and labor
This product is covered by one or more of the following patents:
5,650,624 / 5,721,430 / 5,444,249 / 5,747,808 / 5,834,777 / 5,163,332 /
5,340,986 / 5,502,308 / 6,344,798 / 6,023,069 / 5,370,114 / 5,601,079 /
5,691,704 / 5,767,776 / 5,966,077 / 6,107,925 / 5,798,700 / 5,945,924 /
5,592,147 / 6,255,653 / 6,250,133 / 6,285,290
Warranty
This Telaire product has been examined and tested for proper operation. Please
operate this product only in accordance with the instructions.
Telaire warrants this product against defects in workmanship and materials for a
period of 18 months from the date of purchase by the original owner. If the product
should become defective within this warranty period we will repair or exchange it.
A return authorization number must be obtained from the factory prior to returning
equipment. Items received without a return authorization number will be refused.
Product to be serviced under this warranty should be sent to Telaire, 6860 Cortona Dr,
Suite B, Goleta, CA 93117. Shipment must be prepaid, properly packed and insured.
Telaire is not and will not be liable for any consequential loss or damages that
may occur by reason of purchase and use of this product. The responsibility of
Telaire, in any event, is strictly limited to the replacement/repair of the product.
Telaire seeks to present reliable information concerning the composition,
properties and use of its products, however; (1) All advice concerning selection
and use of any product is provided at no charge and with no warranty. (2) No
warranty is made hereby. Products described herein are warranted to conform to
Telaire specifications only at the time of sale. All sales are subject to Telaire
standard terms and conditions, which are reproduced on the reverse side of each
invoice. All warranties of merchantability and fitness of purpose are disclaimed
and remedy for any breach of warranty is limited to replacement of the defective
product. (3) Telaire assumes no responsibility for any patent liability arising from
the use of any product in a process, manner or formula not designed by Telaire. P/N 62292-006
05/12/2004
