Sper scientific 900030 User manual

Bluetooth IAQ

Anemometer

900030

Instruction Manual

TABLE OF CONTENTS

Introduction............................................................................3

Front Panel Description.........................................................4

Measurement Procedures.....................................................7

Set Up & Calibration............................................................11

Nice Flow App……………………………….....................…..15

Error Codes.........................................................................19

Specications......................................................................21

Warranty..............................................................................24

INTRODUCTION

Thank you for purchasing the IAQ Anemometer which measures:

• CO2

• Air Temperature

• Humidity

• Air velocity & volume

• Dew Point

• Wet Bulb Temperature

This unique instrument allows you to monitor air ow and air

quality and at the same time. Backlit dual display enables you

to choose between an upper display of air velocity, RH or CO2

and a lower display of air temperature, air volume, dew point or

wet bulb temperature. Calculates min/max, multi-point and time

weighted average on all parameters and has a hold function.

View readings on your smartphone in real time via Bluetooth®

with free iOS and Android apps and export a summary the

data together for later analysis. The app will also superimpose

current readings of all parameters on your smart phone photo

of the object being measured. Simple user calibration of

CO2. and RH. Also enables input of air pressure for accurate

compensation of CO2 measurements. The CO2 sensor uses

NDIR (non-dispersive infrared) waveguide technology to

ensure long-term accuracy, and reliability. Comes in a hard

carrying case with 4 AAA batteries. Optional air cones come

in a set with one round cone for vents <7 ½” diameter and one

square cone for vents <12 ½” x 12 ½”. When attached to the

cone the meter automatically calculates air volume without

the need to input vent size. The optional extension rod can be

used with the meter alone, or the cone, eliminating the need

for a ladder.

Upper display: Air velocity, RH, CO2 value (depends on model)

Duration time in average.

Lower display: Air volume, temp., WBT, DP value

(depends on model.)

HOLD: Freezes the current reading.

MAX/MIN: Maximum and minimum reading.

AVG: Multi-points & timed average.

:Battery Low voltage indicator.

ppm : CO2 unit.

m/s, fpm : Air velocity unit.

%RH : Relative humidity unit.

oC, oF : Temperature unit.

CMM, CFM : Air volume unit.

WBT, DP : Wet Bulb, Dew Point temp.

inch2cm2: Area dimension unit.

: Air ow cone attached.

:Vain in this meter.

LCD DISPLAY

• Press and release the Power button to turn the meter on/o󰀨.

• Hold the button down for 2 seconds to enter or exit setup mode.

• Press and release HOLD to freeze the current reading. Press

again to unfreeze readings.

• Hold the button down for 2 seconds to view Minimum and

Maximum values. Hold down again to return to normal mode.

• In average mode press to record data or start timed recording.

• In setup mode press to enter data settings.

• With the meter on, press Lmode to select a lower display of

air temperature, air volume, WBT (Wet Bulb Temperature), or

DP (Dew Point).

• In average mode, press to select they type of average you

seek, press again to return to normal mode.

• In setup mode, press to select category or increase value.

KEY PAD

• Press Umode to select an upper display of air velocity, RH

(Relative Humidity) or CO2.

• In average mode, press to view recorded and average reading of

all parameters.

• In setup mode press to select category or decrease value.

Press + simultaneously to disable auto power o󰀨.

MEASUREMENT PROCEDURES

Power on/o󰀨

Press and release the Power button to turn the meter on/o󰀨.

Auto Power O󰀨

When turned on the meter defaults to auto-o󰀨 mode which

automatically turns the meter o󰀨 after 20 minutes of inactivity.

To override auto-o󰀨 hold + down simultaneously for 2

seconds. “n” will briey appear on the display conrming that

the meter is in normal mode and auto-o󰀨 has been disabled.

Display Units

When initially powered on the meter displays air velocity in

the upper display and air temperature in the lower display.

Press Umode to cycle upper display readings of air velocity,

RH (Relative Humidity) or CO2. Press Lmode to cycle lower

display readings of air temperature, air volume, WBT (Wet

Bulb Temperature), or DP (Dew Point). The meter will default

to your most recent section the next time it is powered on.

Data Hold

Press and release HOLD to freeze the current reading.

“HOLD” appears on the top left corner of the display.

Press again to unfreeze readings.

Max, Min

1. Press Mx/Mn for 3 seconds to view minimum reading

of all parameters. “MIN will appear atop the display and

the minimum values since the meter was turned on will

be displayed.

2. Press Mx/Mn again for 3 seconds to display maximum

readings. “MIN will appear atop the display and the

minimum values since the meter was turned on will be

displayed.

3. Press the up arrow to scroll minimum and maximum

parameters in the upper display and press the down arrow

to scroll parameters in the lower displays.

4. Press Mx/Mn again for 3 seconds to return to the normal

mode.

Average Functions

The meter can calculate multi-point or timed averages on all

parameters. This can also be done via the App (see p. 15)

Multi-Point Average

1. In normal mode press “AVG” for 2 seconds to enter multi-

point average mode.

2. Press enter repeatedly to record specic readings.

3. Once recorded press the to see the average of all the

data points recorded. AVG will ash while the number of

data points will appear in the upper display and the average

reading will displayed in the lower display.

4. Press the to scroll through the average readings of

each parameter.

5. Press “AVG” again to return to normal mode.

Timed Average

1. In normal mode press “AVG” for 2 seconds and the meter

enters multi-point average mode. Press it again to enter

Timed Average mode.

2. Press enter to start recording. The upper display shows the

timed duration in seconds (maximum 19999 seconds), and

the lower display shows the current reading.

3. Press the up arrow to end the recordings and calculate

the timed average. “AVG” begins ashing and the timed

duration in seconds appears on the upper display while the

average reading appears in the lower display.

4. Press to view average readings of other parameters.

5. Press AVG again to return to normal mode.

Air Volume

You have 3 options for measuring air volume:

1. Enter the square dimensions of the vent or duct you wish to

measure directly into the meter. (see Setup p. 11).

2. The App o󰀨ers you additional options for calculating air

volume. (see p. 15)

3. Use the optional airow cones. Make sure the meter is fully

inserted and locked into the cone. indicates that it

recognizes the cone. The meter will now automatically

calculate air volume, without reference to any measurements

you may have previously entered.

Note: The vent size must be no larger than the cone.

CO2

The CO2 sensor is built into the rear of the center of the vane.

Press repeatedly to reach CO2 in the upper display.(See

p. 11 for CO2 calibration). For accurate readings at high

altitudes CO2 should be compensated for air pressure. This

can be done directly on the meter (see Setup P4.0 on p. 11,

or via the App. see p. 15)

Table of contents

Other Sper scientific Measuring Instrument manuals

Sper scientific

Sper scientific 840063 User manual

Sper scientific

Sper scientific 860041 User manual

Sper scientific

Sper scientific 850004 User manual

Sper scientific

Sper scientific 840005 User manual

Sper scientific

Sper scientific 840015 User manual

Sper scientific

Sper scientific 840021 User manual

Sper scientific

Sper scientific 840062 User manual

Sper scientific

Sper scientific 850068 User manual

Sper scientific

Sper scientific 840018 User manual

Sper scientific

Sper scientific 840064 User manual

Sper scientific

Sper scientific 840080 User manual

Sper scientific

Sper scientific 850068 User manual

Sper scientific

Sper scientific 800047 User manual

Sper scientific

Sper scientific 840060 User manual

Sper scientific

Sper scientific 300003 User manual

Sper scientific

Sper scientific 800050 User manual

Sper scientific

Sper scientific 850081DOK User manual

Sper scientific

Sper scientific 850081 User manual

Sper scientific

Sper scientific 860055 User manual

Sper scientific

Sper scientific 800034 User manual

Sper scientific

Sper scientific 300107 User manual

Sper scientific

Sper scientific 840020 User manual

Sper scientific

Sper scientific 300100 User manual

Sper scientific

Sper scientific 801038 User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual