Speco O2BLP1M User manual

Table of contents

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications

Quick Start Guide

O2BLP1M

1Warning and Caution

Package

2

Overview

3 Overview

3

Camera Quick start guide

CD Plastic plug ×4

Drill template

Screwdriver Junction box

4 tapping screws

1 machine screw

* 1

* 2 If the PoE switch is used to power the camera, DC12V power supply is not required.

It is recommended to install the security cap for outdoor installation.

1 Ethernet Connector

2 MIC-Audio Input

3 HP-Audio Output

4 Alarm Output/Input

5 Power Connector *

6 Micro SD Card Slot

7 Zoom +*

8 Zoom -*

9 CVBS output (unavailable)

10 Reset

1

3

4

5

2

ALARM

4 3 2 1

6

7

8

9

10

* 1 It is recommended to install the security cap for outdoor installations.

* 2 DC 12V power supply is not required if a PoE switch or injector is used to power

the camera.

► Connecting Network Cable

① Loosen the nut from the main element.

② Run the network cable (without RJ 45 connector) through both elements.

Then crimp the cable with RJ 45 connector.

③ Connect the cable to the hermetic connector. Then tighten the nut and the

main cover.

2

13

1--ALM-COM

2--ALM-OPEN

3--ALM-INA

4--ALM-GND

Security cap

DC12V

ALARM

4 3 2 1

Installation

4

* Before you start, please make sure that the wall or ceiling is strong enough

to withstand three times the weight of the camera and junction box.

①Open the mounting base and the upper cover of the junction box.

SD Card Installation

Camera Installation with a Junction Box

Insert a micro

SD card

Cover

Open the cover of the camera as shown in the following figure and then insert

a micro SD card. After that, install the cover back to the camera (Note that the

cover shouldn’t be installed unevenly).

Mounting base

Upper cover

② Install the mounting base of the junction box onto the wall by using the

screws provided.

③Fix the mounting base of the camera to the upper cover of the junction

box.

④ Route the cables through the cable hole and connect the camera. Then install

the camera onto the mounting base of the junction box.

Three-axis Adjustment-Before adjustment, preview the image of the camera

on a monitor and then loosen the fixed screws to adjust the camera according to

the figure below to get an optimum angle.

⑤

Tilt 90°

Pan 360°

Rotate

360°

Fixed screws

The monitoring image shall try to cover the lane, entering/exiting vehicles

and these vehicles' plate number shall be always seen in the video.

Try to avoid the objects that will block the camera, such as pillars,

obstacles, doors, etc.

Avoid the scenes with many trees or other moving objects (like humans,

non-motor vehicles).

The monitoring road shall be straight within 165ft in front of/behind the

location of the camera installation and make sure the camera points at the

front or rear of the vehicle.

Overhead Monitoring

The installation height (H) shall range from 15 ~ 20ft.

The distance D (between the location of the camera installation and the

captured area) shall range from 50 ~ 82ft. This distance (D) depends on the

installation height, usually 3 or 4 times as far as the installation height (H).

The distance of the captured area (L) shall be from 50 ~ 65ft.

Configuration requirements of camera and surrounding area

Note: The following installation requirements are based on optimum conditions,

your license capture rate may vary depending on speed, lighting, position, license

plate designs and other factors.

The depression angle of the camera shall range from 10° to 15°.

If the camera is installed on the side of the road, the pan angle of the camera

shall range from 0° to 20°.

If the camera is installed right above the middle of the road, the pan angle

of the camera shall range from -10° to 10°.

Entrance & Exit Monitoring

The installation height (H) shall range from 4.2ft to 5ft.

The distance D (between the location of the camera installation and the

captured area) shall range from 8.2ft to 10ft.

The distance of the captured area (L) shall be from 5ft to 6.5ft.

H

D

L

50~65 feet 50~82 feet

15~20feet

LD

H4.2~5ft

8.2~10ft

5~6.5ft

<40MPH

The depression angle of the camera shall range from 0° to 5°.

The pan angle of the camera shall range from 5° to 20°.

If the captured license plate doesn't meet the above requirement, you can

adjust the pan angle of the camera to correct it.

The tilt angle of the license plate

After the camera is installed, you can log in the web client and view

whether the license plate tilts in the video. The tilt angle shall range from

-5° to 5°.

Web Operation and Login

5

Operation

IP Scanner can search for the device on the local network.

①Make sure that the camera and the PC are connected to the same local network.

The camera is set to DHCP by default.

② Install IP Scanner from the CD and run it after installation.

●

The login interface is shown above. Default user name is admin and password

is 1234. After logging in, follow directions to install applicable plugins.

③ In the device list, you can view the IP address, model number, and MAC

address of each device. Select the applicable device and double click to open

up the web viewer. You can also manually enter the IP address in the address

bar of the web browser.

O2BL P1M 5 2C:F2:07 :4:68:9A n/a n/a

192.1 68.17.2 51