Siemens LVM User manual

SiemensSiemens

Siemens IndustryIndustry

IndustryIndustry

Industry,,

,Inc.Inc.

Inc.Inc.

Inc.

BuildingBuilding

Building

Tecec

ecec

echnologies Dihnologies Di

hnologies Dihnologies Di

hnologies Divisionvision

visionvision

vision

P/N 315-034090-11

INTRODUCTION The Model LVM Live Voice Module from Siemens

Industry, Inc. provides firefighters with a means of

sending live voice messages to specified audio

zones. The LVM has a push-to-talk switch on the

microphone, as well as a retractable coiled cord.

Both the push-to talk switch and the microphone

are supervised.The LVM has a built-in speaker to

preview active tones and messages. Each DAC-

NET in the system (with an LPB) supports up to

five LVMs. Additional LVMs may be

connected remotely using the RNI.

OPERATION

Controls and Indicators The front panel of the LVM contains

six switches and six pairs of LEDS.

Each pair contains one bi-color (red/

green) and one yellow LED. The

functions of the switches and LEDs

are programmed using the Zeus Tool

(Refer to the Zeus Quick Start Guide,

P/N 315-033875). All LEDs can be

programmed ON, OFF, or FLASHING.

These switches are used for manual

control of the voice system.

The functions of the remaining LEDs and push buttons are defined as follows:

PREANNOUNCE TONE (Yellow) When illuminated, indicates that the

preannounce tone is active at the

speakers.

READY TO PAGE (Green) When illuminated, indicates that all

selected zones are ready to be paged.

MONITOR VOLUME These two pushbuttons increase or

decrease the volume of the speaker on

the LVM.

Live Voice Module

Installation Instructions

Model LVM

Figure 1

LVM Live Voice Module

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034090-112

The back of the LVM contains 2 rotary address switches and five diagnostic LEDs,

two plug-in cable connectors for the CAN and two plug-in cable connectors for audio.

(See Figure 2).The function of the diagnostic LEDs are defined as follows:

SCITSONGAIDMVLFONOITPIRCSED

RORRE.ylnoesuyrotcaF

LIAFCIM .detcetedsienohporcimehtfoeruliafanehwydaetsswolgDEL

LIAFNAC .detcetedsikrowt

enNACehtnoeruliafanehwydaetsswolgDEL

LIAFUPC.detcetedsiUPCehtfoeruliafanehwydaetsswolgDEL ot3erugiFnidet

acidnisDELesuacoslalliwnoitidnocliaFUPCehT* .wolleythgil

REWOP.NOsiMVLehtrofrewopehtnehwydaetsswolgDEL

PRE-INSTALLATION Set the board address for the LVM using both of the ten-position rotary switches

located on the back of the board (See Figure 2). Each of these addresses must be a

sub-address of the DAC and must be the same as the addresses assigned in the

Zeus Programming Tool.

Figure 2

LVM Cable Connections, Diagnostics and Address Switches

After setting the address, label each switch or LED. When viewed from the front

panel of the LVM, the labels are on the left and the control switches and LEDs are on

the right.

• Refer to the Zeus configuration for the address of each module and its

assigned functions.

• Remove the label strip from its slot, and type or print a brief function

identifier for each switch.

• After completing the label strip, insert in back into its slot (See Figure 3).

INSTALLATION The LVM mounts to the rear of the inner door in the CAB-1, CAB-2, CAB-3, REMBOX2

or REMBOX4 enclosures. Select the location of the LVM. In CAB-1/-2/-3 it can be

mounted on either side of the PMI/PMI-2, over the two mounting studs in the

desired location. In the REMBOX2/4 the LVM may mount in any of the positions (as

viewed from the front). Secure the LVM to the inner door with the two nuts provided.

(Refer to Figure 4.)

Figure 3

Inserting A Label Into

The Back Of The LVM

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034090-113

When selecting the location to mount the LVM, keep in mind that no modules or

power supplies/extenders can be installed in the space on the CAB-MP or

REMBOX-MP directly behind the LVM.

When using a REMBOX 2/4, the OCM-16 and SIM-16 cannot be used.

INNER DOOR

PMI/PMI-2

LVM

Figure 4

Mounting the LVM To The Rear Of The Inner Door

CAN cable CCL, a 30 inch long 6 wire cable, P/N 599-634214, connects the LVM to

the next CAN module or P3 on the CC-5/CC-2 or P4 on the RNI.

A 24 inch long 10 wire audio cable, P/N 555-134260, connects the LVM to P4 on the

CC-5/CC-2, or JP6 on the PMI, or J1 on the PMI-2 or P1 on the RNI. (Refer to Figure 5.)

Make sure that all cables seat fully into their connectors. Secure the cable in the back

box using cable ties and the tie down points in the enclosure.The cable must have

sufficient slack to allow the inner door to open fully without putting stress on the

cable.

WIRING

Remove all system power before installation, first battery then AC. (To power up,

connect the AC first, then the battery.)

• Each LVM module is a node in the CAN bus.

• Each LVM connects either through the CC-5/CC-2 CAN bus via a plug-in

cable to the DAC or via the RNI.

• Up to 99 CAN modules, in any combination, can be connected to the CAN

bus of each DAC.

• Each LVM module is shipped with one CCL cable.

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Canada Limited

Building Technologies Division

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 Canada

P/N 315-034090-11

Siemens Gebäudesicherheit

GmbH & Co. oHG

D-80930 München

For CE applications in Cerberus E100 systems refer to

Installation Instruction A24205-A334-B844 (English) or A24205-A334-A844 (German).

tnerruCenalPkcaBV420 rewoPtuptuO

tnerruCV42lanimreTwercS xamAm15 DELevitcarepAm1+ riaPkrowteNNAC .xamkaepotk

aepV8

tnerruCenalPkcaBV2.60 .xamAm57 )noissimsnartgsmgnirud(

tnerruCybdnatSV42 xamAm15 DELevitcarepAm1+

NOTES:

1. Five LVMs max. per DAC-NET/LPB.

2. An LVM is not required in the enclosure with the DAC-NET/LPB.

3. Reference RNI Installation Instructions, P/N 315-033420, for complete wiring details.

• Cable connections for the LVM are shown in the following table and in

Figures 5 and 6.

SNOITCENNOCELBACMVL

elbaCnoitpircseD traP rebmuN noitcennoC

LCCgnoL-ELBAC-NAC rotcudnoc-6,.ni03 412436-555NACtx

enehtotMVLehtstcennoC no3Pmorfstcennocroeludom .INRehtno4ProMVLehtot2-CC/5-CC

oiduA elbaC ELBAC-OIDUA rotcu

dnoc-01,.ni42 062431-5552-CC/5-CCaoteludomMVLstcennoC .1PINRro2-IMP/IMPro

TO FMT TO CC-5/-2, PMI/PMI-2 OR RNI*

TO CC-5/-2 OR RNI*TO NEXT CAN MODULE

ERROR

P4 P3

*SEE RNI INSTALLATION INSTRUCTIONS, P/N 315-033420

Figure 5

LVM Wiring

The CAN bus requires a 120 ohm resistance at each end of the loop. Refer to the

DAC-NET Installation Instructions, P/N 315-035100 for details about CAN termination.

Figure 6

Audio and CAN Bus Routing for Multiple LVMs Connected to a Single DAC-NET/LPB

ELECTRICAL RATINGS

Other Siemens Control Unit manuals

Siemens

Siemens SITRANS RD500 User manual

Siemens

Siemens SITRANS PCS 7 Parts list manual

Siemens

Siemens MKB-5 User manual

Siemens

Siemens LME11 series User manual

Siemens

Siemens 3KC ATC3100 User manual

Siemens

Siemens SIMATIC ET 200SP User manual

Siemens

Siemens ST950 User manual

Siemens

Siemens SIMOTION D4 Series User manual

Siemens

Siemens LAL Series User manual

Siemens

Siemens 6AV7861 Series User manual

Siemens

Siemens FM 458-1 DP User manual

Siemens

Siemens SINAMICS G120 CU250S-2 Series Administrator guide

Siemens

Siemens SINUMERIK 840Di Parts list manual

Siemens

Siemens Desigo PXC4.E16 User manual

Siemens

Siemens SIPROTEC 4 7XT71 Series User manual

Siemens

Siemens SIMATIC NET CP 142-2 User manual

Siemens

Siemens Synco RMK770 User manual

Siemens

Siemens TM Timer DIDQ Quick start guide

Siemens

Siemens SIMATIC ET 200SP User manual

Siemens

Siemens SIMATIC TI525 User manual

Siemens

Siemens SIMOTICS CONNECT 400 User manual

Siemens

Siemens SIRIUS ACT 3SU1400-1EK10-6AA0 User manual

Siemens

Siemens GAMMA 5WG1118-4AB01 Service manual

Siemens

Siemens 3VL9800-3MJ00 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual