Shinko CLT-200 User manual

INSTRUCTION MANUAL

FOR

CC-LINK LINK UNIT

CLT-200

Thank you for your purchase of our CC-Link link unit CLT-200.

This manual contains instructions for the mounting, functions, operations and notes when operating

the CLT-200.

For your confirmation of the model and specifications of the units, peruse and understand this instruction

manual before starting operation.

To prevent the accident by mishandling of the units, please arrange to give this manual

into the hands of the operator who actually uses our product.

NOTESTOUSERS CLT-200

******* Notes to users *******

Before operating CLT-200, please understand following matters.

Warning

Turn the power supplied to the instrument OFF before wiring or checking.

If working or touching the terminal on the power ON status, there is a

possibility of Electric Shock which can cause severe injury or death.

Notices

･It is required to set up each switch for CLT before the power supplied

totheunitisturnedON

･The CLT should be surly inserted to the CBT-200 socket to avoid imperfect

contact.

CONTENTS CLT-200

1. Overview

1.1 Overview of CLT-200 ············································································································ 4

1.2 Units and structure when applied to the C series ································································· 4

1.3 System configuration·············································································································· 5

1.4 Parameter exchange ············································································································ 7

2. Model name

2.1 Model name···························································································································· 7

2.2 How to indicate the model name ·························································································· 7

3. Name and functions of the sections ·············································································· 8

4.Setup

4.1 Switch setting ······················································································································· 9

4.2 Communication setting of CC-Link master unit ······································································ 11

5. Mounting

5.1 Site selection··························································································································13

5.2 External dimension drawing ···································································································13

5.3 Mounting to the DIN rail (CBT-200) ························································································13

5.4 Mounting to the CBT-200 ·······································································································13

6. Wiring connection

6.1 Terminal arrangement ············································································································14

6.2 Wiring connection example ····································································································14

7. Communication

7.1 Communication between the master station and remote device station································· 17

7.2 Remote input/output ···············································································································20

7.3 Remote register······················································································································27

7.4 Extended number ···················································································································29

7.5 CC-Link flag operation············································································································33

7.6 Data reading and writing procedure ······················································································38

8. Sequence program example

8.1 System configuration of an example program ········································································ 39

8.2 Sequence program example ··································································································40

9. Specifications

9.1 Standard specifications ··········································································································41

9.2 Optional specification ·············································································································41

10. When troubled······················································································································· 42

OVERVIEW CLT-200

1. Overview

1.1 Overview of CLT-200

If CC-Link link unit is applied to the C series, the C series can be linked to the PLC of Mitsubishi

Electric Corporation.

To the base unit, the power source host link unit, 2-channel temperature control unit and

CC-Link link unit can be mounted.

The Base unit can be mounted to the DIN rail.

The base unit has 2 types.

One type can be mounted by 1 power source host link unit, up to 4 units of 2-channel temperature

control unit and 1 CC-Link link unit.

The other type can be mounted by 1 power source host link unit, up to 8 units of 2-channel

temperature control unit and 1 CC-Link link unit.

1.2 Units and structure when applied to the C series

(1) CC-Link link unit

Model name CLT-200: Link unit to connect to CC-Link master unit.

(2) 2-channel temperature control unit

Model name CCT-235-2□/□: Independent temperature control unit of 2 channels

(3) Power source host link unit

Model name CPT-200: Link unit to supply the power to the CCT and CLT.

(4) Base unit

Model name CBT-210: Base unit to mount the CPT, CCT and CLT unit.

OneCPTisrequiredto1baseunit.

When the CLT is applied, 1 CPT, max. 8 units of CCT and 1 CLT

can be connected. (space for 1 unit is not used.)

CBT-205: Base unit to mount the CPT, CCT and CLT unit.

OneCPTisrequiredto1baseunit.

When the CLT is applied, 1 CPT, max. 4 units of CCT and 1 CLT

can be connected.

 CC-Link is a trademark of the Mitsubishi Electric Corporation.

OVERVIEW CLT-200

1.3 System configuration

nWhen connecting 1 unit of the CLT-200 to the CBT-210.

[Fig.1.3-1]

nWhen connecting plural units of the CLT-200 (max.16 units) to the CBT-210.

[Fig.1.3-2]

CC-Link

CPT-200

CCT-235 CLT-200

PLC of Mitsubishi

CC-Link

master unit

CC-Link

CPT-200

CCT-235 Max.16 units of CLT-200

CC-Link

master unit

PLC of Mitsubishi

OVERVIEW CLT-200

nWhen connecting 1 unit of the CLT-200 to the CBT-205.

[Fig.1.3-3]

nWhen connecting plural units of the CLT-200 (max.16 units) to the CBT-205.

[Fig.1.3-4]

CC-Link

CCT-235 Max.16 units of CLT-200

CC-Link

master unit

PLC of Mitsubishi CPT-200

CPT-200

CC-Link

CCT-235 CLT-200

CC-Link

master unit

PLC of Mitsubishi

OVERVIEW/MODELNAME CLT-200

1.4 Parameter exchange

Parameter exchange is shown as below.

CC-Link Data exchange with the CLT is performed by sequence program.

Masterunit

CC-Link

The CLT receives the sending data from the CC-Link and sends

CLT-200 the data to the CCT.

The CLT receives the response data from the CCT and sends the

datatotheCC-Link.

The CCT receives the sending data from the CLT and performs

CCT-235 the control, then sends the response data of the CCT to the CLT.

2. Model name

2.1 Model name

CLT-200: CC-Link link unit

2.2 How to indicate the model name

Warning

Turn the power supplied to the instrument OFF before confirming the model name

plates.

If working or touching the terminal on the power ON status, there is a possibility

of Electric Shock which can cause severe injury or death.

Model name plates are put on the case and inner assembly.

[Example]

CLT-200

No. x x x x x x

Model name: CLT-200

Option [TC]: Terminal cover

Instrument number (indicated only on the inner assembly.)

NAME AND FUNCTIONS OF THE SECTIONS CLT-200

3. Name and functions of the sections

[Fig.3-1]

①Communication confirming indicator

When communicating between a CCT and CLT, yellow LED blinks.

②Instrument power indicator

When the power supplied to the instrument is turned ON, green LED lights.

③Communication confirming indicator for CC-Link

When CC-Link is communicating, yellow LED lights.

④Error indicator for CC-Link

When an error has occurred during the communication of CC-Link, red LED lights.

When changing baud rate or station number of CC-Link, red LED blinks.

⑤Rotary switch for CC-Link baud rate setting.

It sets the baud rate for CC-Link.

⑥Rotary switch for CC-Link station number setting (the 1st digit)

It sets the CC-Link station number of the CLT.

⑦Rotary switch for CC-Link station number setting (the 2nd digit)

It sets the CC-Link station number of the CLT.

③

④

Communication

terminal block

①

②

LINK

ERR

Top of the unit

⑤

⑦

⑥

SETUP CLT-200

4. Setup

Warning

Turn the power supplied to the instrument OFF before setup.

If working or touching the terminal on the power ON status, there is a possibility

of Electric Shock which can cause severe injury or death.

Notice

Set up each switch of CLT-200 before connecting the unit to the socket of CBT-200.

4.1 Switch setting

Set the rotary switch of CLT-200 using a small screw driver (either Phillips type or flat bladed one).

①Baud rate (data transfer rate) setting of CC-Link

Rotary switch No. 0 1 2 3 4

Baud rate 156kbps 625kbps 2.5Mbps 5Mbps 10Mbps

Do not set the rotary switch number from 5 to 9.

②Station number setting of CC-Link (the 1st digit)

It sets the CC-Link station number (1 to 9) of the CLT.

Setting range: 1 to 64

③Station number setting of CC-Link (the 2nd digit)

It sets the CC-Link address (1 to 6) of the CLT.

Do not set the rotary switch number from 7 to 9.

Setting range: 1 to 64

[Fig.4.1-1]

* Do not set “0” to the 1st and 2nd digit when setting the CC-Link station number.

* For the communication setting of CC-Link master unit, see pages 11 and 12.

①

②

③

Top of the unit

① ②

SETUP CLT-200

nStation number setting

For setting a station number of C series , use a rotary switch located on the top of the CLT-200.

See [Fig. 4.1-1].

Notices

･Be sure to set a station number when connecting the CLT-200 to CC-Link.

However, avoid the same station number on the same line.

･The station number can be set regardless of C series connection order.

･Set the station number of CLT-200 skipping every 4 stations, because 4 stations

are occupied.

[Setting Example]

[Fig.4.1-2]

Front Front

Sta. No. 1 Sta. No. 2 Sta. No. 3 Sta. No. 4 Sta. No. 5 Sta. No. 6 Sta. No. 7 Sta. No. 8 Sta. No. 9

nCC-Link baud rate (data transfer rate) setting

For the CC-Link baud rate setting of CLT-200, use the rotary switch located on the top of the CLT-200.

See [Fig. 4.1-1].

Notice

The baud rates of all the CLT-200s and of CC-Link master station on the same

line should be set as the same rates.

Different settings of baud rate prevent normal data link.

CC-Link

Master

station

(MELSEC)

CLT-200

Station number 1

C series

PLC of Mitsubishi C series

①②

CLT-200

Station number 5

Table of contents

Other Shinko Measuring Instrument manuals

Shinko

Shinko ACD-13A Use and care manual

Shinko

Shinko AER-101-ORP User manual

Shinko

Shinko JIR-301-M Use and care manual

Shinko

Shinko WIL-101-ORP User manual

Shinko

Shinko JC-33A User manual

Shinko

Shinko AER-101-ORP User manual

Shinko

Shinko DFT-700-M User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual