Sewha SI 410 User manual

Digital Weighing Indicator

SI 410

User Manual

Ver.1.0 140825

- 2 -

SI 410 WEIGHING INDICATOR

CONTENTS

1.Before Installation·····································································································-3 -

2.Introduction·············································································································· - 4 -

2-1. Introduction····································································································································- 4 -

2-2. Cautions············································································································································- 4 -

2-3. Features···········································································································································- 4 -

3.Specification ············································································································· - 5 -

4.Installation ·············································································································· - 11 -

4-1. Dimension & Cutting Size··································································································· - 11 -

4-2. Installation Components ······································································································ - 11 -

4-3. Load Cell Installation·············································································································· - 12 -

5.Set-up ······················································································································ - 13 -

5-1. TEST Weight Calibration Mode ························································································ - 13 -

5-2. Simulation Weight Calibration·························································································· - 17 -

5-3. F-FUNCTION Setting··············································································································· - 21 -

5-4. Test Mode ···································································································································· - 39 -

6.Interface ·················································································································· - 40 -

6-1. Serial Interface··························································································································· - 40 -

6-2. External Input····························································································································· - 46 -

6-3. Relay output································································································································ - 46 -

6-4. Current Loop······························································································································· - 47 -

6-5. Analog Output(4~20mA) ····································································································· - 48 -

6-6 Analog Output (0~10V) ········································································································· - 49 -

6-7. Analog Output Setting·········································································································· - 50 -

6-8. Print Interface····························································································································· - 50 -

6-9. BIN IN ··········································································································································· - 51 -

6-10. BCD OUT····································································································································· - 52 -

6-11. Ethernet ···································································································································· - 53 -

6-12. SD Memory Card···················································································································· - 53 -

6-13. Option card combination chart ····················································································· - 54 -

7.Error & Treatment·································································································- 55 -

- 3 -

SI 410 WEIGHING INDICATOR

1. BEFORE INSTALLATION

Caution / Warning Marks

This mark warns the possibility to arrive death or serious injury

in case of wrongly used.

This mark cautions the possibility to arrive serious human body

injury or product lose in case of wrongly used.

Copy Rights

1. All Right and Authority for this Manual is belonged to SEWHA CNM CO., LTD.

2. Any kinds of copy or distribution without permission of SEWHA CNM CO., LTD. will be

prohibited.

3. This manual may be changed as the version is upgraded, without previous notice.

Inquiries

If you have any kinds of inquiries for this model, please contact your local agent or Head Office.

Head Office : SEWHACNM CO., LTD.

Website : http://www.sewhacnm.co.kr

Email : sales@sewhacnm.co.kr

- 4 -

SI 410 WEIGHING INDICATOR

2. INTRODUCTION

2-1. Introduction

Thank you for your choice of this SI 410 Industrial Digital Weighing Indicator.

This SI 410 model is high-performance weighing Indicator.

Please review and learn this instruction Manual and enjoy your process efficiency

with “SI 410”Weighing Indicator.

2-2. Cautions

1. Don’t drop on the ground and avoid serious external damage on item.

2. Don’t install under sunshine or heavy vibrated condition.

3. Don’t install place where high voltage or heavy electric noise condition.

4. When you connect with other devices, please turn off the power of item.

5. Avoid from water damage.

6. For the improvement of function or performance, we can change item specification without

previous notice or permission.

7. Item’s performance will be up-dated continuously base on previous version’s performance.

2-3. Features

1. SI 410 model is standard size indicator which is easy to install on the panel.

2. Front panel is covered with Polycarbonate film, strong against dust and water.

3. RS232 Serial interface is standard installed.

4. User can choose various options; Analog output 4~20mA, 0~10V / RS232C / RS422,

RS485 / ETHERNET CARD / BCD OUT / BIN IN / SD Memory card

- 5 -

SI 410 WEIGHING INDICATOR

3. SPECIFICATION

3-1. Specification

Content

Specification

Analog Part

Display Resolution

1/20,000

Internal Resolution

1/2,000,000 (±1,000,000)

Input Sensitivity

Min 0.1µV/V

Max Signal Input Voltage

Max 3.0mV/V

Load cell Excitation

DC +5V

A/D Conversion Method

Sigma-Delta

Decimal Point

0, 0.0, 0.00, 0.000

Drift

Offset

10PPM/℃

Span

10PPM/℃

Non Linearity

0.001% of Full Scale

Analogue Sampling(sec)

60times / sec(MAX)

Environment

Operating Temperature

Range

-10℃ ~ +40℃ [14℉ ~ 104℉]

Operation Humidity Range

40% ~ 85% RH, Non-condensing

Function

Calibration Mode

Test Weight Calibration Mode

Simulation Calibration Mode

Display

6 digit, 25.4mm(1inch) Red FND for Numbers

7 digit, Red LED for Weight unit

8 digit, Green LED for State alarm

12 digit Greed LED for Arrow

Key Pad

14pcs Standard Key pad

Additional Digital Input

6pcs external input key

Communi-

cation

Serial Port 1

(RS-232)

Data Transference

Command Mode

Serial Printer Mode

Modbus (RTU)

Relay Output

7pcs selectable relay output

Power

AC : 110~240V, Maximum Power Consumption 19W

Size

200mm(W)ⅹ100mm(H)ⅹ126.5mm(D)

Weight : 1250g

- 6 -

SI 410 WEIGHING INDICATOR

3-2. Option

Option1

Serial Port (RS-422)

Option2

Serial Port (RS-485)

Option 3

Serial Port (RS-232)

Option 4

ETHERNET CARD

Option 5

Analog Output(0~20mA)

Option 6

Analog Output(0~10V)

Option 7

BCD OUT

Option 8

BIN IN

Option 9

SD Memory card

3-3. Front Panel

3-3-1. Front Panel (Display / Key Pad)

- 7 -

SI 410 WEIGHING INDICATOR

3-3-2. State LED

LED

State

STEADY

When the weight is stable, ON.

ZERO

When the current weight is zero, ON.

TARE

When the “TARE”function is set, ON.

HOLD

When the “HOLD”function is set, ON.

TxD

When indicator sends date out through serial communication.

RxD

When indicator receives date out through serial communication.

PRT

When the weighing data is printed, ON.

OUT1

When OUT1 (Relay) is operated, ON.

OUT2

When OUT2 (Relay) is operated, ON.

OUT3

When OUT3 (Relay) is operated, ON.

OUT4

When OUT4 (Relay) is operated, ON.

OUT5

When OUT5 (Relay) is operated, ON.

OUT6

When OUT6 (Relay) is operated, ON.

OUT7

When OUT7 (Relay) is operated, ON.

RUN

When the weighing process is going on.

HIGH

When OUT4 is ON, Under Function 223-03.

LOW

Activated on only under display test mode.

Displayed weight unit under Function 110-00

Displayed weight unit under Function 110-01

Displayed weight unit under Function 110-02

Displayed weight unit under Function 110-03

pcs

Displayed weight unit under Function 110-04

Displayed weight unit under Function 110-05

Displayed weight unit under Function 110-06

- 8 -

SI 410 WEIGHING INDICATOR

3-3-3. Key Operation

- Press 4 times within 3secs, to enter to Function setting mode.

- Press 4 times within 3secs, to enter to “Hidden function”mode.

- Make the weight value to Zero

- Number 1

- Set the TARE Function

1st input : “TARE”, 2nd input : “TARE Reset”

(When “HOLD”or weight value is ZERO, then this key doesn’t work.)

- Number 2

- Set the “HOLD”Function

1st input : “HOLD”, 2nd input : “HOLD Reset”

- Number 3

- Product number setting

- Number 4

- Print out

- Number 5

- Number 6

- SP1 set value setting

- Number 7

- SP2 set value setting

- Number 8

- SP3 set value setting

- Number 9

- SP4 set value setting

- Number 0

- Cancel or Move to previous step.

- Save and Move to next step.

- 9 -

SI 410 WEIGHING INDICATOR

3-3-4. Hot key

Double tare setting

(Once tare is set, Another tare is overlapped.)

Print the Sub-total out

Forced discharge

Display the current weight during 5 secs.

Display the Sub-total weight during 5 secs.

Display the Grand-total weight during 5 secs.

Print the Grand-total out

Delete the Sub-total weight

Delete the Grand-total weight

Max accumulated weighing count : 999,999times

Over 999,999times return to “0” time

Max accumulated weight display : 999999999 (g, kg, ton)

Over 999,999,999 (g, kg, ton) return to “0” (g, kg, ton)

- 10 -

SI 410 WEIGHING INDICATOR

3-4. Rear Panel

(1) AC Power input terminal

(2) External input terminal: User selectable 6EA (Function 233~238)

(3) Serial Interface terminal

Terminal

RxD

TxD

GND

C/L

RS –232

GND

C/L

(4) Loadcell Input terminal

Terminal

EXC+

EXC-

SIG+

SIG-

SHLD

Loadcell

EXC+

EXC-

SIG+

SIG-

SHEILD

(5) Relay output terminal: User selectable 7EA (Function 226~232), COM is common.

Terminal

Relay

output

RELAY 1

RELAY 2

RELAY 3

RELAY 4

RELAY 5

RELAY 6

RELAY 7

RELAY

COM

(6) Analog output terminal

Terminal

4~20mA

(-)

(+)

Option

0~10V

(-)

(+)

Option

(7) Option serial interface terminal

Terminal

RS –232C

GND

Option

RS - 422

TxD-

TxD+

RxD-

RxD+

Option

RS - 485

Unused

D-

D+

Option

Please check the Comm. and other specification in the label, attached on the cover

plate first, and make connection according to that information.

(5)Relay output

(2)External Input

(3)Serial I/F

(4)Loadcell Input

(1)Power

(6)Analog output

(7)Option Serial I/F

Other manuals for SI 410

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual