Securitytronix ST-IP6FE User manual
ST-IP6FE QUICK
START GUIDE
www.securitytronix.com
www.nacebrands.com
ST-IP6FE QUICKSTART GUIDE
1
1
Thank you for purchasing our product. If there are any questions, or
requests, please do not hesitate to contact the dealer.
About This Document
This manual applies to the ST-6FE fisheye network camera.
This manual may contain several technical incorrect places or
printing errors, and the content is subject to change without notice.
The updates will be added to the new version of this manual. We will
readily improve or update the products or procedures described in
the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of this
product. UL has only tested for fire, shock or casualty hazards as
outlined in UL’s Standard(s) for Safety, UL60950-1. UL Certification
does not cover the performance or reliability of the security or
signaling aspects of this product. UL MAKES NO REPRESENTATIONS,
WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING
RELATED FUNCTIONS OF THIS PRODUCT.
ST-IP6FE QUICKSTART GUIDE
2
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to
comply with the limits for a digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized European
standards listed under the Low Voltage Directive 2006/95/EC, the
EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU.
ST-IP6FE QUICKSTART GUIDE
3
3
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points. For more information
see: www.recyclethis.info.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your
supplier or to a designated collection point. For more information
see: www.recyclethis.info
ST-IP6FE QUICKSTART GUIDE
4
4
Safety Instruction
These instructions are intended to ensure that user can use the
product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings
are neglected.
Cautions: Injury or equipment damage may occur if any of the
cautions are neglected.
Warnings
●In the use of the product, you must be in strict compliance with
the electrical safety regulations of the nation and region. Please
refer to technical specifications for detailed information.
●Input voltage should meet both the SELV (Safety Extra Low
Voltage) and the Limited Power Source with 24 VAC or 12 VDC
according to the IEC60950-1 standard. Please refer to technical
specifications for detailed information.
Warnings Follow these
safeguards to prevent
serious injury or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.
ST-IP6FE QUICKSTART GUIDE
5
5
●Do not connect several devices to one power adapter as
adapter overload may cause over-heating or a fire hazard.
●Please make sure that the plug is firmly connected to the power
socket. When the product is mounted on wall or ceiling, the
device shall be firmly fixed.
●If smoke, odor or noise rise from the device, turn off the power
at once and unplug the power cable, and then please contact
the service center.
Cautions
● Make sure the power supply voltage is correct before using the
camera.
● Do not drop the camera or subject it to physical shock.
● Do not touch sensor modules with fingers. If cleaning is
necessary, use a clean cloth with a bit of ethanol and wipe it
gently. If the camera will not be used for an extended period,
please replace the lens cap to protect the sensor from dirt.
● Do not aim the camera at the sun or extra bright places.
Blooming or smearing may occur otherwise (which is not a
malfunction), and affect the endurance of sensor at the same
time.
● The sensor may be burned out by a laser beam, so when any
laser equipment is in use, make sure that the surface of the
sensor will not be exposed to the laser beam.
ST-IP6FE QUICKSTART GUIDE
6
6
● Do not place the camera in extreme heat or cold (the operating
temperature shall be-22°F ~+140°F, or -40°F ~ 140°F if the
camera model has a heater equipped), dusty or damp locations,
and do not expose it to high electromagnetic radiation.
● To avoid heat accumulation, good ventilation is required for
operating environment.
● Keep the camera away from liquid while in use.
● If mail in warranty service is required, the camera shall be
packed in its original packing, or packing of the same type.
● Regular part replacement: a few parts (e.g. electrolytic
capacitor) of the equipment shall be replaced regularly
according to their average life time. The average time varies
because of differences between operating environment and use,
so regularly checking is recommended for all users. Please
contact your dealer for more details.
● Improper use or replacement of the battery may result in hazard
of explosion. Replace with the same or equivalent type only.
Dispose of used batteries according to the instructions provided
by the battery manufacturer.
● If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to
disassemble the camera yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or
maintenance.)
ST-IP6FE QUICKSTART GUIDE
7
7
Table of Contents
1 Appearance Description ................................................................. 8
1.1 Overview of Fisheye Camera ........................................... 8
1.2 Disassembling the Camera .............................................. 9
2 Installation.................................................................................... 11
2.1 Ceiling Mounting ........................................................... 12
2.2 Wall Mounting with a Slant Mounting Base .................. 14
2.3 Wall Mounting with a Junction Box ............................... 17
2.4 Wall Mounting with a Bracket ....................................... 19
3 Setting the Network Camera over the LAN .................................. 21
4 Accessing via Web Browser .......................................................... 26
ST-IP6FE QUICKSTART GUIDE
8
8
Appearance Description1
Overview of Fisheye Camera1.1
Overview of the Fisheye Camera Figure 1-1
Figure 1-2 Disassembly of Fisheye Camera
67
4
5
1
8910
3
2
ST-IP6FE QUICKSTART GUIDE
9
9
Description of Overview Table 1-1
No.
Description
No.
Description
1
Camera Body
6
Ethernet Interface
2
Reset
7
RS-485 Interface
3
Micro SD Card Slot
8
Power Interface
4
Camera Cover
9
Audio In
5
Alarm Interfaces
10
Audio Out
Disassembling the Camera1.2
Steps:
1. Loosen the lock screw on the camera cover.
2. Remove the camera cover, and you can see the oval removable
panel.
3. Loosen the two screws on the removable panel.
4. Move the oval panel aside, and you can see the reset button and
the micro SD card slot.
Table of contents
Other Securitytronix Security Camera manuals
Securitytronix
Securitytronix ST-BTWD600IR40-B User manual
Securitytronix
Securitytronix ST-BTLI540IR20 User manual
Securitytronix
Securitytronix ST-DLI540IRVP-B User manual
Securitytronix
Securitytronix ST-BT540IR30VF User manual
Securitytronix
Securitytronix ST-D700IRVP3.6-B2 User manual
Securitytronix
Securitytronix ST-DLI600VP3.6-B-W User manual
Securitytronix
Securitytronix ST-D600DN2812-DSHB User manual
Securitytronix
Securitytronix ST-DWDVF2812-720B/W User manual
Securitytronix
Securitytronix ST-IP2FWD User manual
Securitytronix
Securitytronix ST-CVTMD520-WPIR-W User manual
Securitytronix
Securitytronix ST-PTZ480-22X User manual
Securitytronix
Securitytronix ST-D420IR6-B User manual
Securitytronix
Securitytronix ST-HD-D2812M-2MP User manual
Securitytronix
Securitytronix ST-PTZ550-27 User manual
Securitytronix
Securitytronix ST-DWD1000IRVP2812 Series User manual
Securitytronix
Securitytronix HD-COAXINATORTVI ST-HDC2PTZ User manual
Securitytronix
Securitytronix ST-IP-BT3.6-1 User manual
Securitytronix
Securitytronix ST-D7002812-B User manual
Securitytronix
Securitytronix HD-COAXINATORTVI ST-HDC2FD User manual
Securitytronix
Securitytronix ST-D540IRVP2812 User manual
