Salus EP101 User manual

Instruction Manual

Model No EP101

Programmable

Heating Controller

Salus EP101 Manual 001:89 21/11/10 11:49 Page 1

Salus EP101 Manual 001:89 21/11/10 11:49 Page 2

PRODUCT COMPLIANCE

This product complies with the essential requirements of the

following EC Directives:

•Electro-Magnetic Compatibility directive 2004/108/EC

•Low Voltage Directive 2006/95/EEC

•EC Marking directive 93/68/EEC

SAFETY INFORMATION

These instructions are applicable to the Salus Controls model stated

on the front cover of this manual only, and must not be used with

any other make or model.

These instructions are intended to apply in the United Kingdom

only, and should be followed along with any other statutory

obligations.

This accessory must be fitted by a Competent person, and

installation must comply with the guidance provided in the current

editions of BS7671 (IEE Wiring Regulations) and Part ‘P’ of the

Building Regulations. Failure to comply with the requirements of

these publications could lead to prosecution.

Always isolate the AC Mains supply before opening or

removing the unit from the wall or wall box.

When fitting batteries don’t mix old and new batteries

together. Do not use rechargable batteries.

Please leave these instructions with the end user where they should

be kept in a safe place for future reference.

EP101 INSTRUCTION MANUAL 3

Salus EP101 Manual 001:89 21/11/10 11:49 Page 3

INTRODUCTION

A A programmable heating controller is used to switch the heating system

in your home on and off as needed. It works by controlling the heating

boiler according to a series of programmed settings that take effect at

different times of the day.

The EP101 from Salus Controls is

a stylish and accurate 5/2 or 7 day

programmable heating controller

with a large, easy to read Liquid

Crystal Display (LCD). This

controller has been specifically

designed to be used for single

channel Volt Free or 230V AC

heating applications.

A simple jumper switch changes

the EP101 between 5/2 or 7 day

programming.

Features

•Timed control of central heating

•Large LCD with blue backlight

•Stylish Casing

•Volt Free Contacts

•Built-in start up programme

•12 or 24 hour clock display

•Advance 1 hour facility

•Holiday Function

•5/2 or 7 day programming

•Three On / Off periods

•Memory backup

EP101 INSTRUCTION MANUAL

Salus EP101 Manual 001:89 21/11/10 11:49 Page 4

INSTALLATION

Please read the important safety information at the start of this manual

before you begin to install the device.

The ideal position to locate the EP101 programmable heating controller is

about 1.5m above floor level. It should be mounted in a location where the

controller is easily accessible, reasonably lit and free from extremes of

temperature.

The electrical connections to the EP101 are made to the supplied industry

standard backplate. This simplifies installation, as no connections are made

to the controller itself. Connection details are shown below - no Earth

connection is required for the correct and safe operation of the EP101, but

a parking terminal is provided to connect an Earth wire if one is present.

230V AC Switching

Terminal Description Backplate

N Mains Neutral

L Mains Live

1 Hot Water Off

2 No Connection

3 Switched Live (output)

4 230V link from Mains Live

(do not remove)

Earth Parking

(no electrical connection)

EP101 INSTRUCTION MANUAL 5

Salus EP101 Manual 001:89 21/11/10 11:49 Page 5

After installing the backplate in a suitable location, wiring connections can be

made as shown above. The following criteria apply to the installation:

•

The incoming AC mains supply should be 230V AC and fused at 6 amps.

•

Optimum cable size for installation is 1.5 mm2; wiring colours should be

in accordance with the current requirements of the IEE Wiring Regulations.

•

Cable entry should be from the rear of the backplate.

•

All wiring connections should be securely made, and be firmly

gripped beneath the terminal square brass washer.

Do not restore the mains supply to the system until all associated items are fully

installed.

NOTE: All electrical installation work should be carried out

by a suitably qualified Electrician or other competent person.

If you are not sure how to install this programmable thermostat consult either

with a qualified electrician, heating engineer or your boiler / heating system

supplier for advice on how to continue.

Do not remove or refit the EP101 onto the backplate without the mains

supply to the system being isolated.

Volt Free Switching

Terminal Description Backplate

N Mains Neutral

L Mains Live

1 Normally Closed (NC)

2 No Connection

3 Normally Open (NO)

4 Volt Free Common

Earth Parking

(no electrical connection)

EP101 INSTRUCTION MANUAL

Salus EP101 Manual 001:89 21/11/10 11:49 Page 6

JUMPER SETTINGS

Changes to the jumper settings should only be made by the Engineer

carrying out the installation or other qualified person.

The installer should select the jumper positions required if changes need to

be made to the factory default settings. These jumpers are found on the

rear of the controller.

Jumper Function Default

Program Type Movable jumper for 5-2 or 7 5-2

individual days programming. programming

Internal Movable jumper for Internal backup

Backup Battery enabling or disabling the battery disabled

internal backup battery.

The installer should enable the internal backup battery before fitting the

controller to ensure user settings are retained – the battery will be kept

charged from the controller mains supply.

EP101 INSTRUCTION MANUAL 7

Salus EP101 Manual 001:89 21/11/10 11:49 Page 7

AFTER INSTALLATION

After completing installation and powering up the EP101 for the first time

the controller will behave in the following way:

All the indicators on the display and the backlight will be turned on for two

seconds. After two seconds, the EP101 will then operate in Normal mode

(controller output OFF).

All the controller settings will be returned to default values. If the Reset

Button is pressed, the EP101 will behave in the same way as described

above, except that any previously saved user settings will be deleted and

overwritten with the default settings.

EP101 INSTRUCTION MANUAL

Salus EP101 Manual 001:89 21/11/10 11:49 Page 8

USER INTERFACE AND CONTROLS

The status and operation of the

EP101 can be clearly seen on the

large backlit Liquid Crystal Display

(LCD) - this display allows the user

to see at a glance the current status

of the heating system.

There are few user controls for the EP101, making the controller very easy to

operate. These controls are shown below, along with a description of each of

their functions.

User Control Function Summary

Key / Operation Symbol Functions

+1Hr Temporary override

UP key Increases the selected setting

DOWN key Decreases the selected setting

BACKLIGHT / Manually turns on the LCD backlight

HOLIDAY key for 5 seconds, or activates /

deactivates Holiday Override

MODE key Selects operating mode

SELECT key Selects a clock or programme setting

SET key Sets a clock or programme setting

RESET button Resets the controller to default

(original factory) settings

EP101 INSTRUCTION MANUAL 9

Salus EP101 Manual 001:89 21/11/10 11:49 Page 9

OPERATION

The EP101 is configured and

adjusted by the use of an intuitive

user interface with a minimal

number of user controls.

The backlit LCD gives a highly

visible, easily readable indication of

the controller status.

Setting the Time

Press and hold SET and SELECT when the EP101 is in Normal mode for three

seconds to enter the Clock setting mode. Releasing both keys will display

“12 hr” or “24 hr” and SET, as shown below:

Release the SET and SELECT keys and

press UP or DOWN to toggle between 12

and 24 hour time format.

Pressing and releasing SELECT will then display the time and a SET

indicator, with all other indicators cleared from the display. The hour part

of the time will be flashing to indicate that it is the currently selected item

and is ready to be adjusted.

Press the UP or DOWN keys to increase or

decrease the hour setting – the selected

item will stop flashing while a key is

pressed, and will resume flashing when

you release the key.

Press the SELECT key to select the ‘minutes’ section of the time. Set the

minutes in the same way as the hour by using the UP and DOWN keys.

EP101 INSTRUCTION MANUAL

Salus EP101 Manual 001:89 21/11/10 11:49 Page 10

Other manuals for EP101

Table of contents

Popular Thermostat manuals by other brands

EWELLY

EWELLY EW-181 manual

Prolon

Prolon T1100 Hardware guide

Computherm

Computherm Q20 operating instructions

Heatmiser

Heatmiser neoStat user manual

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA user manual

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat user manual

Saswell

Saswell SAS920XWHB-7-S-RF User manual and warranty card

Aircalo

Aircalo TFP1-ET85P2 operating manual

Honeywell

Honeywell CM721 user manual

Carrier

Carrier DEBONAIR 33CS Installation and operating instructions

Lennox

Lennox iHarmony Zone Thermostat Installation and setup guide

Gemtech

Gemtech GT7000 Operation

Rollei

Rollei Smartes 45000 manual

Sinope

Sinope TH1300RF user guide

Honeywell

Honeywell RLV4305 owner's guide

Honeywell

Honeywell Prestige 2.0 THX9421 manual

NuTone

NuTone NTBZ48 Installation & operation guide

Stelpro

Stelpro MAESTRO ASMT402AD user guide