Salus 091FLRF User manual
Programmable Room Thermostat with RF (Volt Free)
Model 091FLRF
User’s Manual
1
GB
INTRODUCTION
This thermostat can replace most common residential thermostats
and is designed to be used with electric, gas or oil heating control
systems.
Unlike ordinary single unit design thermostats, this is a new type of
thermostat separating the operational functions into two units. The
Receiver serves for wiring connections and heat on/off control. The
Control Centre serves as user interface and temperature sensing/
control. The two units are linked by Radio Frequency.
The Receiver is easily installed using the Industry Standard back
plate supplied (for mounting purposes only as no wiring is required
when installing the control centre).
The back plate can be mounted directly to the wall surface.
Installing & Wiring the Receiver
Caution:
Switch off the electric source before installing the receiver.
We recommend that the installation be performed by trained
personnel.
1) This must be 230V AC and fused at 13 amps max.
2) Select a suitable indoor location free from water and moisture.
3) The receiver should not be shielded from the RF signal in any way,
follow ‘Testing the RF Transmission’ section (PAGE 7
2
GB
) of this manual before deciding on a nal location for the receiver
and control centre units.
4) The Receiver should be mounted in a suitable location that is both
accessible for the connection of mains and control wiring, and
allows good reception of the RF signal. The Receiver needs a 230V
AC mains supply to operate, and this should be fused appropriately
(13A max.). The Receiver should be
mounted in a location where it will
not come into contact with water,
moisture or condensation.
The Receiver On/Off switch is
accessible from the front face of the
Receiver, as shown in this picture:
On the front cover of the Receiver you
will see that there is the On/Off switch and two Light Emitting diodes
(LEDs). The switch allows you to turn off the Receiver if necessary
to prevent it calling for heat. The top LED (red) will illuminate when
the switch is in the ‘On’ position and the unit is receiving power. The
bottom LED (green) illuminates when the Receiver unit is receiving
a heat call transmission from the Control Centre.
3
GB
The wiring terminals and RF Address Code
setting DIP switches are located on the rear
of the Receiver, as shown in this picture:
4
GB
Multiple Thermostat Installations
Please note, if using more than one Receiver in the same
installation, be sure that there is at least a 1 metre gap
between receiver units to avoid RF interference.
When installing multiple thermostats you should ensure that you
assign different address codes for each Receiver following the ‘RF
Address Code Setting’ section of this manual. Each Receiver should
be introduced to the installation one at a time with all other receiver
units switched off, also make sure that the batteries are removed
from all other Control Centres.
Install each unit following the ‘TESTING THE RF TRANSMISSION’
section of this manual. Once you are happy with the operation of one
unit you may install the next. Once all Receiver ‘s are installed, if one
unit then seems to function abnormally, try changing the address code
of the control centre & its corresponding receiver again taking care
that the new code given is different to all others in the installation.
The control centre sends RF On/Off signals every 10 min to ensure
the receiver is in the correct state. If for some reason the 1st RF
signal is interrupted you may notice the control centre has started/
stopped calling for heat but the receiver hasn’t switched. Simply wait
10 minutes until the next RF signal is transmitted and the receiver
unit should switch.
5
GB
RF Address Code Setting
If there is another user nearby, e.g. in the next house, your receiver
may be fault triggered by their transmitter. You may select a different
RF address code to prevent this. The receiver can only respond to
RF transmissions with the same address code setting as its own
address code.
1. To adjust address code of Receiver & Control Centre, simply push
up or down on the 5 dip switch levers. The leavers are numbered
1 to 5 from left to right.
Note :
1. Set dip switch on receiver in same ON position as in transmitter.
ON position is marked on each part shown in picture.
Address Code Dip
Switch Leavers.
Factory Defaut Setting Dip switch 1 - 5 in On position.
1 2 3 4 5
ON
6
GB
Factory Defaut Setting Dip switch 1 - 5 in On position.
1 2 3 4 5
ON
Address Code Dip
Switch Leavers.
12345
ON
7
GB
TESTING THE RF TRANSMISSION
It is important to site the Receiver and Control Centre in locations
where the RF signal cannot be interrupted. The receiving range
between Control Centre and Receiver is 60M in open area. Many
factors can affect the RF transmission, shortening the operating
distance e.g. shielding by thick walls, foil back plasterboard, metal
objects such as ling cabinets, general RF interference etc, However,
the range is enough for most household applications.
It is advisable to test the RF transmission from the intended Control
Centre location to the Receiver location before xing the Control
Centre to the wall.
1. Press UP button until the set-point temperature is higher than room
temperature by a few degrees.
2. Wait for a few seconds. The animated fun (heat call indicator) should
appear on the bottom right of the LCD on the control centre.
3. Check the green LED on the receiver unit. It should be
illuminated.
4. Press Down button to adjust the set-point temperature to be lower
than room temperature. Wait for a few seconds. The animated ame
(heat call indicator) should disappear and the green LED should
switch off.
5. If at step 3 the LED is not illuminated, press RESET and try to place
the Control Centre closer to the Receiver, repeating steps 1 to 4.
6. Alternatively you can try and alter the address code following the
‘RF Address Code Setting (page 5) of this manual, then repeat
steps 1 to 3.
Note that the RESET button on the Control Centre should be pressed
after altering the add ress code.
8
GB
INSTALLAING THE CONTROL CENTRE
Select a suitable location for the control centre. The location of the
control centre can greatly affect its performance. If it is located where
air circulation cannot reach, or exposed to direct sun light, it will not
adjust the room temperature properly.
To ensure proper operation, the control centre should be installed
at an inside wall with freely circulating air. Find a place where your
family is usually occupied.
Avoid close proximity to heat generating appliances (e.g. TV, heater,
refrigerator) or exposed to direct sunlight. Do not install near a door
where the thermostat will suffer from vibration.
Using the template provided, drill two ø6mm holes in the wall. Insert
the wall anchors and tighten the left screw with 3mm clearance. Fix the
control centre by putting it over the screwhead and slide it rightward
(note the keyhole-like opening at the back of the thermostat). Tighten
the remain screw to lock it in place.
slide it
rightward
Screw now
Note: If the wall is made of wood, there is no need to use the wall
anchors. Drill two ø2.7mm holes instead of ø6mm.
Other manuals for 091FLRF
5
Table of contents
Other Salus Thermostat manuals
Salus
Salus VS20WRF User manual
Salus
Salus ST320RF User manual
Salus
Salus RT510BC+ User manual
Salus
Salus DIGITAL PROGRAMMABLE THERMOSTAT User manual
Salus
Salus RT510 User manual
Salus
Salus ST621TX User manual
Salus
Salus RT310SR User manual
Salus
Salus CT100 User manual
Salus
Salus iT500 User manual
Salus
Salus Rogers Smart Thermostat 7 Series User manual
Salus
Salus WBRT520TX User manual
Salus
Salus EP110 User manual
Salus
Salus T105 RF User manual
Salus
Salus ST620 User manual
Salus
Salus Optima S User manual
Salus
Salus BTRP230 User manual
Salus
Salus AHTR5024 User guide
Salus
Salus RT300RF User manual
Salus
Salus RT510WBC User manual
Salus
Salus QUANTUM SQ610RF User manual
Popular Thermostat manuals by other brands
Saswell
Saswell SAS920XWHB-7-S-RF User manual and warranty card
Aircalo
Aircalo TFP1-ET85P2 operating manual
Honeywell
Honeywell CM721 user manual
Carrier
Carrier DEBONAIR 33CS Installation and operating instructions
Lennox
Lennox iHarmony Zone Thermostat Installation and setup guide
Gemtech
Gemtech GT7000 Operation
