Ricoh Aficio CL3000 User manual

Options

32

1

Bluetooth Interface Unit Type A

R

CAUTION:

Important

❒Before manipulating the Bluetooth

Interface Unit, touch any metal

thing to discharge static electricity.

Static electricity thing damage the

Bluetooth Interface Unit.

❒Do not subject the Bluetooth Inter-

face Unit to physical shocks.

A

AA

ACheck the contents of the package

for the following:

❖

❖❖

❖Bluetooth

•Interface Unit

•Card

•Bluetooth Module

•Antenna Cap

B

BB

BTurn off the power, and then un-

plug the power cable.

C

CC

CRemove the two screws that fas-

ten the controller board on the

back of the printer.

The removed screws will be used

in step Lto fasten the controller

board.

•Do not touch inside the controller

board compartment. It may

cause a machine malfunction or

a burn.

ZHBP410E

ZHBP510E

ZHBP520E

ZHBPA921E

ZHBP080E

AresPGBOptionSetup-F_FM.book Page 32 Friday, July 26, 2002 1:11 PM

Bluetooth Interface Unit Type A

33

1

D

DD

DWhile holding the handle, pull

out the controller board slowly.

E

EE

ERemove USB2.0 Interface Unit.

Note

❒The removed screws will be

used in step G

❒Lift the end of USB2.0 Interface

Unit (A), and then remove it

from the controller board (B).

F

FF

FAttach the Bluetooth Interface

Unit. Insert the end of the Blue-

tooth Interface Unit to the open-

ing (A

AA

A), and then push down

until it clicks (B

BB

B).

Confirm that the Bluetooth Inter-

face Unit is firmly connected to the

controller board.

G

GG

GFasten the Bluetooth Interface

Unit on the controller board using

the screws removed in step E

EE

E.

H

HH

HInsert the card slowly into the

Bluetooth Interface Unit with its

side labeled "INSERT" facing up

until it stops.

ZHBP020E

ZHBPB460E

ZHBP450E

1

2

ZHBP190E

1

2

ZHBP200E

ZHBP530E

AresPGBOptionSetup-F_FM.book Page 33 Friday, July 26, 2002 1:11 PM

Options

34

1

I

II

IPress the antenna to extend it.

J

JJ

JAttach the antenna cap over the

antenna.

K

KK

KAdjust the Bluetooth module to

the slot, and then insert vertically.

L

LL

LAlign the controller board to the

top and bottom rails, and then

push in slowly until it stops.

Note

❒When installing other options

on the controller board, do not

close the controller board, but

go to the steps for installing the

option.

Important

❒The printer may not work prop-

erly if the controller board is not

set properly.

M

MM

MFasten the controller board to the

printer with the two screws re-

moved in step C

CC

C.

ZHBPA530E

ZHBPA920E

ZHBP540E

ZHBO550E

ZHBPB560E

AresPGBOptionSetup-F_FM.book Page 34 Friday, July 26, 2002 1:11 PM

Other manuals for Aficio CL3000

6

Table of contents

Other Ricoh Printer Accessories manuals

Popular Printer Accessories manuals by other brands

Star Micronics

Star Micronics TSP800 Series install guide

REA

REA JET HR pro 2K user manual

HP

HP Laserjet,Color Laserjet 4si user guide

oliser

oliser MS 45 instructions

Roland

Roland DU2-64 Supplementary manual

Xerox

Xerox EFI EXP6000 Specification sheet

Canon

Canon Finisher-T1 Service manual

Sharp

Sharp FO-1MK Service manual

Labelmate

Labelmate PM-300 user manual

Epson

Epson T6248 Product information sheet

Epson

Epson OT-BZ20 user manual

Canon

Canon TonerRobot EP-27 instruction manual

GBC

GBC 16 Series user guide

Canon

Canon INNER 2-WAY TRAY-E1 INSTALLATION PROCEDURE

Develop

Develop SD-509 installation manual

Kyocera

Kyocera KM-6230 Instruction handbook

Triumph Adler

Triumph Adler DF-710 Instruction handbook

Citizen

Citizen CBM-202PC Series user manual