RCP ADF-B06 User manual
Pulse Oximeter
Model # ADF-B06
Pulse Oximeter
V1.1 REMOTE CARE PARTNERS PAGE 2
TABLE OF CONTENTS
INTRODUCTION ............................................................... 3
NOTES ON SAFETY ........................................................... 3
Handling batteries properly: ...................................... 4
PRODUCT OVERVIEW...................................................... 5
SYMBOLS.......................................................................... 6
POWER-ON KEY/FUNCTIONAL KEY OPERATIONS .......... 6
ALERT SOUND SETTINGS .................................................. 7
BRIGHTNESS SETTING ....................................................... 8
POWER SAVING FUNCTION ............................................ 8
ALERT RANGE SETTING .................................................... 9
TAKING A MEASUREMENT............................................. 10
About the display...................................................... 11
CLEANING ..................................................................... 12
DISINFECTING ................................................................ 12
MAINTENANCE .............................................................. 13
TECHNICAL SPECIFICATION.......................................... 14
STORAGE AND TRANSPORTATION ............................... 16
CONTACT INFORMATION AND NOTICES..................... 17
FCC Compliance Statement ................................... 17
Pulse Oximeter
V1.1 REMOTE CARE PARTNERS PAGE 3
Model # ADF-B06
INSTRUCTION MANUAL
INTRODUCTION
This Pulse Oximeter is provided to you by Remote
Care Partners (RCP), for use exclusively with the
health monitoring program from your provider.
Please read this manual carefully and keep it
handy for future reference.
NOTES ON SAFETY
Please read this section carefully before using the
unit.
Do not attempt to open the electrical
compartment of the Oximeter.
Periodically change the contact position
between the Oximeter probe and the finger for a
measurement that lasts a long time. Adjust the
position of the probe before the measurement
lasts two hours, and check the integrity of the
skin, the blood circulation condition of the finger
as well as the position of the finger.
Do not use on newborn babies.
Consult your provider if the result is outside the normal
range. A normal %SpO2 is 95% or greater.
A normal PR is between 60-100.
Pulse Oximeter
V1.1 REMOTE CARE PARTNERS PAGE 4
Do not directly expose your eyes to light-emitting
components of the Oximeter, as that could
cause harm to your eyes.
For details about clinical limitations and
contraindications, please carefully consult the
relevant medical literature.
Warning: Do not use the Oximeter in an
environment with any inflammable gases,
inflammable anesthetic, or other inflammable
substances.
Warning: Dispose of exhausted batteries in
accordance with environment protection
regulations.
Warning: Do not use the Oximeter in an MRI or CT
environment.
Warning: Do not operate the Oximeter when it is
damp, wet, or has condensation. Avoid moving
the Oximeter from an excessively cold
environment to a high-temperature moist
environment.
Handling batteries properly:
As soon as old batteries run out, replace them
with new batteries.
•Do not use old and new batteries together.
•Align the polarities of batteries correctly.
•When the unit will not be used for more than 3
months, remove the batteries. Otherwise, batteries
may leak and cause damage to the unit.
Pulse Oximeter
V1.1 REMOTE CARE PARTNERS PAGE 5
PRODUCT OVERVIEW
Symbol of oxygen saturation
Measured value of oxygen saturation
Bar graph
Plethysmogram
Measured value of Pulse rate
PI
Symbol of pulse rate
Battery power indication/Bluetooth symbol
(alternately displayed)
Pulse Oximeter
V1.1 REMOTE CARE PARTNERS PAGE 6
SYMBOLS
Symbol
Description
BF-type application part
Caution: Please see this manual.
%SpO
2
Symbol of oxygen saturation
bpmR
Symbol of pulse rate
Bluetooth symbol
When end users abandon this product,
they must send the product to the
collection place
for recycling.
POWER-ON KEY/FUNCTIONAL KEY
OPERATIONS
After powering on the Oximeter, hold the power-
on key/functional key for about one second. The
Oximeter shows a parameter setting interface.
Press or hold the power-on/functional key to
perform corresponding operations. Hold it to set
an item or press it to switch an option or switch
the display mode. Press means no more than 0.5
seconds, while Hold means more than 0.5
seconds.
Pulse Oximeter
V1.1 REMOTE CARE PARTNERS PAGE 7
ALERT SOUND SETTINGS
Hold the power-on key/functional key while the
Oximeter is in powered-on state.
Parameter setting interface 1 is displayed.
Move "*" to the corresponding option by pressing
the function key. Hold the function key to set Alm
to on and set Beep to off.
When Alm is set to on and the measured values
of the blood oxygen saturation and pulse rate go
beyond the upper limit or lower limit, the
Oximeter gives off an alert sound.
When Alm is set to off and the measured values
go beyond the limit, the Oximeter will not give
any alert sound.
When Beep is set to on, a tick will be heard along
with pulse beats during pulse rate measurement.
When Beep is set to off, no sound will be output
along with pulse beats during pulse rate
measurement.
While the "*" symbol stays on the Restore option,
hold the function key to restore factory settings.
Pulse Oximeter
V1.1 REMOTE CARE PARTNERS PAGE 8
BRIGHTNESS SETTING
On parameter interface 1, press the functional
key to select the Brightness option and then hold
the functional key to set the brightness to a value
ranging from 1 to 5. The greater the value, the
greater the brightness of the screen.
POWER SAVING FUNCTION
The ADF-B06 has a power-saving feature. It can
save power by reducing screen brightness
automatically. If you leave your finger in the
device for more than 150 seconds, the brightness
will reduce to level 1. To make it return to the
original brightness level, press the function key.
Pulse Oximeter
V1.1 REMOTE CARE PARTNERS PAGE 9
ALERT RANGE SETTING
On parameter interface 2, press the functional
key to switch between options. On this interface,
you can set the upper limit and lower limit of
SpO2 Alm and PR Alm.
While the "*" symbol stays on the +/-option, hold
the function key to set the option to +or -.
In +mode, select the corresponding option and
hold the functional key to increment the upper or
lower limit; in -mode, hold the functional key to
decrement the upper or lower limit.
Move "*" to the Exit option and hold the function
key to return to the monitoring interface.
Pulse Oximeter
V1.1 REMOTE CARE PARTNERS PAGE 10
Do not allow other people to use your pulse
oximeter. The pulse oximeter is specifically
assigned to you and you only. Allowing other
people to use your pulse oximeter can mislead
your provider.
TAKING A MEASUREMENT
1. Squeeze the closed end of the device to
open the other end. Stick one finger
completely into the rubber pad cavity of the
Oximeter,
2. Keep the fingernail surface upward and
release the closed end so the device fits
snugly on your finger.
3. Press the power key to power on the
Oximeter. If you do not completely insert your
finger into the cavity, the measurement may
be inaccurate.
4. The reading will automatically transfer to the
RCP SmartHub and will then be sent to your
provider.
Other manuals for ADF-B06
1
Table of contents
Other RCP Measuring Instrument manuals
