Rae MultiRAE Plus Guide
The Hazardous Environment Detection Company
MultiRAE Plus
Using the
MultiRAE Plus
personal multigas
monitor
Firmware v 3.12B
The Hazardous Environment Detection Company
Training Agenda
• MultiRAE Plus features
• Turning on the MultiRAE Plus
• Recommended Daily Start-up Procedure
• User displays
• Alarm modes
• Programming displays
• Calibration
The Hazardous Environment Detection Company
MultiRAE Plus Features: Sensors
• Oxygen: 0-30%
• Combustibles: 0-100% of LEL
• Toxic sensors: select two from CO,
H2S, SO2, NO, NO2, Cl2, HCN, NH3,
PH3
• VOC monitor: 0-2000 PPM
The Hazardous Environment Detection Company
MultiRAE Plus Features: Easy Sensor Access
• New innovative
casing design
• Easy access to
sensors with
penny, nickel, or
dime
The Hazardous Environment Detection Company
MultiRAE Plus Features: Reliability
• Extremely rugged for extensive field use
• Weather proof case
•-4
°F to 113°F (-20°C to 45°C)
• 4-way power: Li-Ion(NiCad), alkaline or
run continuously on 110 VAC and 12 VDC
• Runs 10-12 hours with pump
• RFI protection against radio interference
• Intrinsically safe: Class I, Division I,
Groups A, B, C, D; UL, cUL, ATEX
• LEL over-range protection
The Hazardous Environment Detection Company
MultiRAE Plus Features: Rugged Case
Buzzer &
Exhaust
Display Charger
Port Serial
Port
The Hazardous Environment Detection Company
MultiRAE Plus Features: Simple Faceplate
Light
Sensor
Alarm LEDs
• Three buttons on a sealed membrane
faceplate:
– Y/+ (horn): clears & tests alarms
– N/- (light): turns on manual backlight for
90 seconds
–MODE(ON)
The Hazardous Environment Detection Company
MultiRAE Plus Features: Rugged Boot
External Filter
Rugged
Rubber
Boot
Belt Clip
The Hazardous Environment Detection Company
MultiRAE Plus Features: Internal Pump
• Makes remote sampling easy
• Sample draw over 100 feet!
• External filter for added protection
• Pump stall feature: when moisture is detected
or when pump is blocked the pump will shut
off, protecting the MultiRAE Plus from
potential damage
• ~150cc/min at low flow, ~250cc/min at high
flow
• Only use teflon tubing when PID is installed
The Hazardous Environment Detection Company
MultiRAE Plus Features: External Filter
• Always use the external filter
• Replace when it looks very dirty
• Replace when MultiRAE Plus is in
pump alarm with the filter on and you
can clear the pump alarm with the
filter off.
You wouldn’t leave your house
without putting on your pants
so don’t use the MultiRAE Plus
without its external filter!
Table of contents
Other Rae Measuring Instrument manuals
Rae
Rae AreaRAE Installation guide
Rae
Rae AutoRAE Lite User manual
Rae
Rae QRAE II User manual
Rae
Rae GammaRAE II User manual
Rae
Rae MeshGuard User manual
Rae
Rae MultiRAE Plus PGM-50/4 User manual
Rae
Rae QRAE 3 User manual
Rae
Rae NeutronRAE II User manual
Rae
Rae DoseRAE 2 User manual
Rae
Rae microrae User manual
Rae
Rae DoseRAE 2 User manual
Rae
Rae TN-204 User manual
Rae
Rae ppbRAE 3000 User manual
Rae
Rae GammaRAE II Responder User manual
Rae
Rae Q-RAE User manual
Rae
Rae MiniRAE Lite User manual
Rae
Rae ToxiRAE Pro PID User manual
Rae
Rae UltraRAE 3000 User manual
Rae
Rae ppbRAE 3000 User manual
Rae
Rae MiniRAE 2000 PGM-7600 User manual
