Protimeter BaleMaster GRN6165 Installation instructions
Protimeter BaleMaster® GRN6165
User Instructions
AAS-INS6165, Rev. A
August 2017
A
mphenol
Advanced Sensors
PROTIMETER
BaleMaster (GRN6165)
Protimeter Moisture Meter
Page 2 Protimeter BaleMaster GRN6165
1 SafetyConsiderations
Caution note for the Bale Probe- The Bale Probe point is extremely
sharp and should be handled with due care. The point should be covered with
the cap provided with the probe when not in use
Calibration of unit - The accuracy specifications of the product are valid
for one year from the date of calibration.
Periodic calibration checking, as outlined in section 4 , is advised.
Only operate the measuring instrument properly, for its intended
purpose and within the parameters specified in
the technical data. Readings from moisture meters are not definitive but are
used to help a professional make informed judgement to the material’s
moisture condition. Conductive material such as salts, carbon and metal can
give false positive readings.
2Introduction
The Protimeter BaleMaster is a conductivity moisture meter designed for
measuring moisture level of baled products such as straw and hay. The
instrument is calibrated for wheat straw and may be used to take relative
measurements in other baled products.
Protimeter BaleMaster GRN6165 Page 3
3 Moisture Measurement inBales
Measure moisture in bales as follows:
Note: Before using the stainless steel probe, be sure it is thoroughly clean
and dry. The probe must not be wet when measuring moisture.
a.Connect the Bale Probe to the instrument and switch ON by pressing and
holding button.
b.Push the Bale Probe in to the bale to the required depth. Note the reading
on thedisplay.
Note: When assessing the moisture content (mc) of whole bales, it is
recommended that the average value is obtained from numerous readings
taken from different sides and at different depths.
c.To obtain the correct average value, use the following moisture
measurement ranges as aguideline:
- Less than 15% mc: bales are in a safe condition for storage.
- Greater than 15% mc: bales are not in a safe condition for storage.
Additional drying is recommended.
d.After use, switch the instrument OFF by pressing and holding the
button, or leave the instrument to switch OFFautomatically.
4 CalibrationCheck
Calibration can be checked using the Protimeter Calcheck device (Part #
BLD5086) and a 2-pin moisture probe (Part # BLD5079), connected via the
Bale probe socket. Correctly calibrated BaleMaster instruments register a
value in the range 14.0 – 14.4 at 20°C across the Calcheck.
5 Care andMaintenance
When the BaleMaster is not in use, keep it in its pouch together with its
accessories. Clean and dry the probe, and wrap it in the bubble wrap. Then
store the probe for later use. Replace the batteries when the low battery power
symbol appears on the display, or remove the batteries if the instrument is not
going to be used for extended periods.
Page 4 Protimeter BaleMaster GRN6165
6 ReferenceMode
Measure the material until the meter reading is stable. Then, press for 2
seconds. This will store the reading until the mode changes or the meter turns
off. Now, all readings taken thereafter will be displayed as normal, and below
you will see a second reading that shows if the material is measured above or
below the original reading. Reference mode can be useful when trying to
establish what materials are above or below a point of reference or dry standard.
7 OperatingBaleMaster
Switch On:
Press the ON/OFF button.
The unit turns on, with the LCD displaying all the segments and sweeping the
LED bar graph.
Protimeter BaleMaster GRN6165 Page 5
Measurements:
The numeric measurement and color LED will be shown, as well as “DRY”
(green) or “AT RISK” (yellow) or “WET” (red), based on the measurement
shown.
8.5-15 DRY (Green), 15.1-19.5 AT RISK (Yellow), 19.6-36.8 WET (Red)
Page 6 Protimeter BaleMaster GRN6165
Reference Mode of Measurement:
While the first reading is displayed on the screen, press and hold the
button for 2 seconds to enter the Reference Mode. The display will be similar to
the one shown on the next page.
To return to the normal measurement mode, press again.
Settings:
Press and hold the button and switch on the unit by pressing . Hold
both the buttons until the BaleMaster displays theversion.
Release buttons while it shows the version number. The unit enters
Settings Mode.
Protimeter BaleMaster GRN6165 Page 7
DRY, AT RISK and WET Settings:
The first screen to appear in Settings is the DRY, AT RISK and WET setting
screen.
This screen sets whether the indication on the display needs to be switched
ON or OFF. When it is ON, the moisture condition will be displayed on the
screen. When it is OFF, no indication is displayed on screen.
Use the button to turn ON/OFF thesettings.
If the unit detects no key press for 2 seconds in the Settings screen, it
moves to the next setting.
Pressing the button, after you have entered the desired setting, it will
save the setting and move the screen to the next setting.
Page 8 Protimeter BaleMaster GRN6165
Buzzer ON/OFF Settings:
Once the DRY, AT RISK and WET settings are entered, the next setting turns
the Buzzer ON or OFF.
To change the settings, press the button.
If the unit detects no key press for 2 seconds in the Settings screen, it
moves to the next setting.
Pressing the button, after you have entered the desired setting, will
save the setting and move the screen to the next setting.
Protimeter BaleMaster GRN6165 Page 9
Backlight Settings:
Once the Buzzer settings are entered, the next setting turns the Backlight
ON or OFF.
To change the settings, press the button.
If the unit detects no key press for 2 seconds in the Settings screen, it
moves to the next setting.
Pressing the button, after you have entered the desired setting, it will
save the setting and move the screen to the next setting.
Page 10 Protimeter BaleMaster GRN6165
Auto Off Time Settings:
When Auto Off is set, the unit will shut down automatically at a specified time
between 1 and 6 minutes, if there is no key press detected within the set time.
For example, if the Auto Off time is set as 1, then the unit will automatically
shut down after one minute when no key is pressed.
The duration will change based on the set time of 1- 6 minutes.
If the Auto Off time is set to be “0”, then the unit will not automatically turn
off. A user must manually turn it off by
pressing and holding the button for 5 sec.
Turn off time can be set by pressing the button, and can be saved by
pressing .
After you save this setting, the unit will exit to the measurement screen.
Other Protimeter Measuring Instrument manuals
Protimeter
Protimeter MMS Plus User manual
Protimeter
Protimeter Digital Mini BLD5702 User manual
Protimeter
Protimeter BLD5765 User manual
Protimeter
Protimeter BLD7705 User manual
Protimeter
Protimeter BLD5765 User manual
Protimeter
Protimeter Grainmaster i User manual
Protimeter
Protimeter MMS3 User manual
Protimeter
Protimeter Surveymaster User manual
Protimeter
Protimeter Surveymaster BLD5365 User manual
Protimeter
Protimeter TimberMaster BLD5609 User manual
