Prorack K945 User manual
K945
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 6 x 6 x 6 x 6
Revision No: 1A 1
Fitting Kit K945
MAX kgs (lbs)
W/P WHD
Iveco
Daily Low Roof, 4dr Van 15-+ NZ 100 kgs (220 lbs) 100 kgs (220 lbs)
Daily Low Roof, 4dr Van 15-+ ZA 100 kgs (220 lbs) 100 kgs (220 lbs)
Daily Low Roof, 4dr Van May 15-+ AU 100 kgs (220 lbs) 100 kgs (220 lbs)
Daily Mid Roof, 4dr Van 15-+ AU 100 kgs (220 lbs) 100 kgs (220 lbs)
Daily Mid Roof, 4dr Van 15-+ NZ 100 kgs (220 lbs) 100 kgs (220 lbs)
Daily Mid Roof, 4dr Van 15-+ ZA 100 kgs (220 lbs) 100 kgs (220 lbs)
2
Fitting Kit K945
X
A B C 1 2 3
Daily Low Roof, 4dr Van 15-+ (NZ) 1060mm 1860mm 2660mm 1050mm 1050mm 1050mm
41 3/4ths" 73 1/4ths" 104 3/4ths" 41 5/16ths" 41 5/16ths" 41 5/16ths"
Daily Low Roof, 4dr Van 15-+ (ZA) 1060mm 1860mm 2660mm 1050mm 1050mm 1050mm
41 3/4ths" 73 1/4ths" 104 3/4ths" 41 5/16ths" 41 5/16ths" 41 5/16ths"
Daily Low Roof, 4dr Van May 15-+ (AU) 1060mm 1860mm 2660mm 1050mm 1050mm 1050mm
41 3/4ths" 73 1/4ths" 104 3/4ths" 41 5/16ths" 41 5/16ths" 41 5/16ths"
Daily Mid Roof, 4dr Van 15-+ (AU) 1400mm 2300mm 3200mm 735mm 735mm 735mm
55 1/8ths" 90 9/16ths" 126" 28 15/16ths" 28 15/16ths" 28 15/16ths"
Daily Mid Roof, 4dr Van 15-+ (NZ) 1400mm 2300mm 3200mm 735mm 735mm 735mm
55 1/8ths" 90 9/16ths" 126" 28 15/16ths" 28 15/16ths" 28 15/16ths"
Daily Mid Roof, 4dr Van 15-+ (ZA) 1400mm 2300mm 3200mm 735mm 735mm 735mm
55 1/8ths" 90 9/16ths" 126" 28 15/16ths" 28 15/16ths" 28 15/16ths"
3
Fitting Kit EN
K945
Items you will require:
●Tape measure
Pen
Flat-head screwdriver
Craft knife
Side cutters or tin snips
Hammer
8mm (3/8") punch
Cordless drill
Depth stop
Vacuum cleaner
Rust inhibitor
Small paint brush
Neutral cure silicon sealant
Rivet gun
Attention:
●Attaches with riveted mounts under rubber
ditch mould. Professional installation
advised.
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
4
Fitting Kit EN
K945
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Assemble front and rear plugs to tracks.
Note: Rear plug shown in picture.
●Carefully select position on vehicle roof
making sure that your crossbar lengths will
match selected positions for the tracks.
●Apply long lengths of masking tape to
vehicle roof in both positions.
●Make sure there is no interference between
what you intend to carry with aerials,
sunroof or tailgate.
5
Fitting Kit EN
K945
●Tracks can be fitted either parallel or
tapered to match vehicle roof shape.
●Parallel Tracks:
A1 & A2 are equal
B1 & B2 are equal
C1 & C2 are equal
D1 & D2 are equal
●Tapered Tracks:
A1 & A2 are different
B1 & B2 are equal
C1 & С2 are equal
D1 & D2 are equal
●With help from another person, carefully lay
tracks over the masking tape and mark
rivet hole positions with a pencil or pen.
●Take care not to move the tracks until the
holes are marked out.
●Use drill bit supplied, to drill rivet holes in
marked positions.
●Take care not to drill too deep.
●Vacuum and clean swarf from channel.
●Treat holes to prevent corrosion.
6
Fitting Kit EN
K945
●Remove masking tape and apply silicon
sealant around drilled holes.
●Sit tracks on roof and line up tracks with
drilled holes.
●Insert rivets through the tracks and into
drilled holes.
●Fit pop rivet nozzle supplied with tracks to
your rivet gun.
Note: It is a standard thread to fit most rivet
guns. Use low pressure on air rivet guns.
●Ensure that the front plugs are at the front
of the track and rear plugs at the rear.
●Rivet tracks to roof.
●Slide metal T-bolt into the track channel via
the entrance on the rear end plug.
7
Fitting Kit EN
K945
Fitment
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
8
Fitting Kit EN
K945
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
●Make sure the pad fits into the holes
underneath the foot.
9
Fitting Kit EN
K945
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
●Ensure that the crossbar is adjusted evenly
at both ends.
●Mount crossbar over metal T-bolt.
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
●Tighten the plastic knob.
●Ensure the plastic knob is in the position
shown when fully tightened.
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K192 User manual
Prorack
Prorack K701 User manual
Prorack
Prorack K085 User manual
Prorack
Prorack WHISPBAR S45 Operation and installation manual
Prorack
Prorack K105 User manual
Prorack
Prorack K422 User manual
Prorack
Prorack K053 User manual
Prorack
Prorack K133 Operation and installation manual
Prorack
Prorack K473 User manual
Prorack
Prorack K1007 User manual
Prorack
Prorack K485 User manual
Prorack
Prorack K692 User manual
Prorack
Prorack K304 User manual
Prorack
Prorack K514 User manual
Prorack
Prorack K361 User manual
Prorack
Prorack K389 User manual
Prorack
Prorack K820 User manual
Prorack
Prorack WHISPBAR S41 Operation and installation manual
Prorack
Prorack K073 User manual
Prorack
Prorack K686 User manual
