Prorack K927 User manual
K927
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 1 x 2 x 1
x 4 x 4 x 1 x 4
x 2 x 2
Revision No: 2B 1
Fitting Kit K927
MAX kgs (lbs)
W/P WHD
Mitsubishi
Triton Club Cab, 4dr Ute Apr 15-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Triton Club Cab, 4dr Ute Apr 15-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Triton Double Cab, 4dr Ute Apr 15-+ AU 75 kgs (165 lbs) 100 kgs (220 lbs)
Triton Double Cab, 4dr Ute Apr 15-+ NZ 75 kgs (165 lbs) 100 kgs (220 lbs)
2
Fitting Kit K927
X
A B C 1 2 3
Triton Club Cab, 4dr Ute Apr 15-+ (AU) -240mm 300mm - 877mm 818mm -
-9 -7/16ths" 11 13/16ths" - 34 1/2ths" 32 3/16ths" -
Triton Club Cab, 4dr Ute Apr 15-+ (NZ) -240mm 300mm - 877mm 818mm -
-9 -7/16ths" 11 13/16ths" - 34 1/2ths" 32 3/16ths" -
Triton Double Cab, 4dr Ute Apr 15-+ (AU) -275mm 525mm - 877mm 795mm -
-10 -13/16ths" 20 11/16ths" - 34 1/2ths" 31 5/16ths" -
Triton Double Cab, 4dr Ute Apr 15-+ (NZ) -275mm 525mm - 877mm 795mm -
-10 -13/16ths" 20 11/16ths" - 34 1/2ths" 31 5/16ths" -
3
Fitting Kit EN
K927
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
4
Fitting Kit EN
K927
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Attaches to factory-fitted mounting points
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
5
Fitting Kit EN
K927
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
6
Fitting Kit EN
K927
Fitment
●Lift and pull ditch moulding back towards
you and remove from the vehicle.
●Mark a reference point for the front and
rear mounting points with a pen as shown.
●Use drill bit supplied, to drill holes in
marked positions.
7
Fitting Kit EN
K927
●Re-install rubber ditch mould back into roof
channel and click into place.
●Select grubscrews and screw into the
vehicle's fixed points.
●Do not over tighten.
●Repeat for all four positions.
●Use the following grubscrew lengths:
A = 70mm (2 3/4")
B = 55mm (2 1/8")
8
Fitting Kit EN
K927
●Refer to the underside of the pad for the
part number.
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 218A
B = 295A
C = 296A
●Place crossbars on pads ensuring the pads
fit into the holes underneath the foot and
the grubscrew passes through the hole in
the foot.
●Repeat for all four positions.
9
Fitting Kit EN
K927
●Tighten the plastic knob. The side with the
nut showing should be facing up.
●Ensure the plastic knob is in the position
shown when fully tightened.
●Repeat for all legs.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K340 User manual
Prorack
Prorack K464 User manual
Prorack
Prorack K137 Operation and installation manual
Prorack
Prorack PR3097 User manual
Prorack
Prorack K855 User manual
Prorack
Prorack K751 User manual
Prorack
Prorack K133 Operation and installation manual
Prorack
Prorack K491 User manual
Prorack
Prorack K536 User manual
Prorack
Prorack K979 User manual
Prorack
Prorack K129 User manual
Prorack
Prorack K434 User manual
Prorack
Prorack K530 User manual
Prorack
Prorack K586 User manual
Prorack
Prorack K1206 User manual
Prorack
Prorack K091 User manual
Prorack
Prorack PR3077 User manual
Prorack
Prorack K504 User manual
Prorack
Prorack K083 User manual
Prorack
Prorack K007 User manual
