Prorack K673 User manual
K673
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 2 x 4 x 2 x 1
x 1 x 2 x 4 x 2
x 1 x 1
Revision No: 1A 1
Fitting Kit K673
MAX kgs (lbs)
W/P WHD
Honda
CR-V 2WD, 5dr SUV 12-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
CR-V S/SE, 5dr SUV 12-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
CR-V LX/EX, 5dr SUV 12-+ US 75 kgs (165 lbs) 75 kgs (165 lbs)
CR-V S, 5dr SUV 12-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
2
Fitting Kit EN
K673
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
3
Fitting Kit EN
K673
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment.
●Ensure each end of the crossbar is
adjusted equally.
4
Fitting Kit EN
K673
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●A = Clear
B = Grey
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 963A
B = 964A
C = 965A
5
Fitting Kit EN
K673
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
6
Fitting Kit EN
K673
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 11-04-239
B = 11-04-246
C = 11-04-247
●Place rubber pads (supplied with fitting kit)
on the vehicle roof. Pad may vary in shape
to that shown.
●Make sure the pad fits into the holes
underneath the foot.
7
Fitting Kit EN
K673
Fitment
●Clamps directly to edge of roof under the
doors
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 5 Nm (3.7 ft lb).
8
Fitting Kit EN
K673
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
9
Fitting Kit EN
K673
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K824W User manual
Prorack
Prorack K730 User manual
Prorack
Prorack K567 User manual
Prorack
Prorack K546 Operation and installation manual
Prorack
Prorack K892 User manual
Prorack
Prorack K514 User manual
Prorack
Prorack K548 User manual
Prorack
Prorack K431 User manual
Prorack
Prorack PR3206 User manual
Prorack
Prorack K496 Operation and installation manual
Prorack
Prorack Whispbar Q20 User manual
Prorack
Prorack K560 User manual
Prorack
Prorack K474 User manual
Prorack
Prorack K075 User manual
Prorack
Prorack K868 User manual
Prorack
Prorack K902 User manual
Prorack
Prorack K663 User manual
Prorack
Prorack Fitting Kit K440 User manual
Prorack
Prorack K566 User manual
Prorack
Prorack K1228 User manual
