Prorack K730 User manual
K730
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4 x 4 x 8 x 4
x 4
Revision No: 1A 1
Fitting Kit K730
MAX kgs (lbs)
W/P WHD
Chevrolet
Orlando, 5dr MPV 10-+ EU 68 kgs (149 lbs) 68 kgs (149 lbs)
Orlando, 5dr MPV 11-+ ZA 68 kgs (149 lbs) 68 kgs (149 lbs)
2
Fitting Kit K730
X
A B C 1 2 3
Orlando, 5dr MPV 10-+ (EU) 250mm 960mm - 932mm 910mm -
9 13/16ths" 37 13/16ths" - 36 11/16ths" 35 13/16ths" -
Orlando, 5dr MPV 11-+ (ZA) 250mm 960mm - 932mm 910mm -
9 13/16ths" 37 13/16ths" - 36 11/16ths" 35 13/16ths" -
3
Fitting Kit EN
K730
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
4
Fitting Kit EN
K730
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Set bars to length (revert to rear of these
instructions).
●Please check the front of this manual for
information relating specifically to your
vehicle.
5
Fitting Kit EN
K730
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
6
Fitting Kit EN
K730
Fitment
●Open or remove fixed-point covers.
●Hook clamps into the fixed points on the
vehicle.
●Hook small claw into rear of the clamping
block
●Hook large claw into front of the clamping
block
●Ensure the clamp pin is inserted into the
fixed point and the clamp sits flat to the
body side.
7
Fitting Kit EN
K730
●Apply protective strip as shown.
●Place ditch mould insert over the clamp.
●Ensure internal clamp sits upright.
8
Fitting Kit EN
K730
●Fit rubber pad (supplied with crossbar) to
foot.
●Make sure the pad fits into the holes
underneath the foot.
●Place crossbar foot over clamp bolt.
●Tighten the plastic knob. The side with the
nut showing should be facing up.
9
Fitting Kit EN
K730
●Ensure the plastic knob is in the position
shown when fully tightened.
●Repeat for all four positions.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K646 User manual
Prorack
Prorack K376 User manual
Prorack
Prorack K915 Operation and installation manual
Prorack
Prorack K425 User manual
Prorack
Prorack K777 User manual
Prorack
Prorack K073 User manual
Prorack
Prorack K731 User manual
Prorack
Prorack K408 User manual
Prorack
Prorack K892 User manual
Prorack
Prorack K045 User manual
Prorack
Prorack K879 User manual
Prorack
Prorack K716 User manual
Prorack
Prorack K618 User manual
Prorack
Prorack PR3208 User manual
Prorack
Prorack K1188 User manual
Prorack
Prorack K389 User manual
Prorack
Prorack K686 User manual
Prorack
Prorack K333 User manual
Prorack
Prorack K495 User manual
Prorack
Prorack K496 Operation and installation manual
