Prorack K324 User manual

FittingKit

K324

Fitting Instructions for Basic Carrier

x 8

x 4

Revision No:

1.1

FittingKit

K324

First Time Installation

Remove parts from packaging and check

contents. Contact your Prorack dealer if parts

are missing or damaged.

This kit fits type A, B, C and D.

These instructions show type A crossbar

fitted. They also apply to type B, C and D.

Use keys to remove covers.

FittingKit

K324

Use hex screwdriver to reverse adjusting

screw 10 turns.

Press adjusting screw and pull crossbar legs

out. Refer to the crossbar instructions for

crossbar adjustment.

Ensure each end of the crossbar is adjusted

equally.

Remove clamp block by pressing backwards.

FittingKit

K324

Remove both pins from each leg (use

spanner located inside left hand cover to

assist).

Detach foot from leg. Store loose parts in a

safe place.

Repeat for all legs.

Select a guttermount assembly from fitting

kit. Unscrew and remove clamps.

FittingKit

K324

Assemble guttermount assembly into leg

(ensure guttermount blade interlocks with

leg).

Using short capscrew and washer, secure

assembly onto leg (use Hex Screwdriver

supplied with crossbar to assist)

Use two M5 x 12 mm self tapping screws to

secure the leg to the guttermount blade.

Do not over tighten.

Repeat for all legs.

FittingKit

K324

Fitment

Place crossbar on vehicle. Minimum

recommended spacing between the bars is

700mm (unless otherwise stated).

Place crossbar into gutter of vehicle.

Adjust crossbar in or out to suit vehicle.

Refer to the crossbar instructions for

crossbar adjustment.

Loosely position crossbar ensuring the

guttermount blade is hard against the inside

of the vehicle gutter.

Tighten adjusting screw to 5 Nm.

FittingKit

K324

Loosely line up clamp over the vehicle gutter.

Use same capscrew and washer to secure

clamp onto leg.

Repeat for all legs.

Check crossbar is securely attached to the

vehicle.

Use keys to fit and lock covers

FittingKit

K324

CAUTION:

Recheck all fasteners immediately after a load is

applied to the crossbars.

Regularly check screws are tight.

FittingKit

K324

Maintenance

Clean the car roof and surfaces of the

product that will be in contact with the car

roof.

Follow the fitting instructions for fitting the

product to your vehicle. Make sure all steps

are carried out in order.

Set crossbars a minimum distance of 700mm

apart where no other distance is specified in

the fitting instructions. This is especially

important when carrying long loads.

Check unit is securely attached whenever

you refit it to the vehicle. If the unit feels

loose, refer to the fitting instructions and

readjust.

Some sunroofs and radio antennae cannot

be used when the product is fitted.

Do not modify this product.

Refer to the maximum permitted load

capacity specified in the fitting instructions.

Do not exceed the vehicle manufacturers

roof load rating if it is lower than the

maximum load capacity specified in the fitting

instructions.

Loads should not overhang the sides of the

product and be evenly distributed with the

lowest possible centre of gravity.

Long loads should be secured with non-

elastic straps to the front and rear of the

vehicle.

Objects with pointed ends (skis) should be

carried with the pointed ends to the rear of

the vehicle.

Remove all loose or removable objects from

the load prior to loading.

Make sure all loads are securely fastened

with non-elastic straps. Check regularly

during longer journeys.

FittingKit

K324

A loaded roof rack system can alter the

performance of your vehicle. Be especially

aware of the effects of side winds, changing

of direction, and braking performance. Avoid

rapid acceleration and deceleration. Drive

carefully.

Note that the total height of the vehicle

increases when upright loads are carried.

Products should be locked during transport if

they have locks fitted.

Check and replace worn out or defective

parts.

Keep the product clean and maintained.

Never drive into a car wash with the roof rack

system fitted.

Lubricate locks and adjusting screws at

regular intervals.

Remove the products from the vehicle when

not in use. Make sure all loose parts are

stored safely.

Hubco Automotive Ltd

P. O. Box 11017

Christchurch

NEW ZEALAND

www.whispbar.com

Table of contents

Other Prorack Automobile Accessories manuals

Prorack

Prorack K134 User manual

Prorack

Prorack K596 User manual

Prorack

Prorack K834 User manual

Prorack

Prorack K894 User manual

Prorack

Prorack K482 Operation and installation manual

Prorack

Prorack K577 Operation and installation manual

Prorack

Prorack K129 User manual

Prorack

Prorack K069 User manual

Prorack

Prorack K328 User manual

Prorack

Prorack K320 User manual

Prorack

Prorack PR3090 User manual

Prorack

Prorack K740 User manual

Prorack

Prorack K1255 User manual

Prorack

Prorack PR3074 User manual

Prorack

Prorack K997W User manual

Prorack

Prorack K639 User manual

Prorack

Prorack K945 User manual

Prorack

Prorack 567 User manual

Prorack

Prorack K164 User manual

Prorack

Prorack K934 Operation and installation manual

Prorack

Prorack K781 User manual

Prorack

Prorack K783 User manual

Prorack

Prorack K373 User manual

Prorack

Prorack WHISPBAR S55 Operation and installation manual

Popular Automobile Accessories manuals by other brands

James Baroud

James Baroud Odyssey user guide

Motorola

Motorola i50sx owner's manual

Yakima

Yakima 9MM STANDARD BIKE MOUNT instructions

Feniex

Feniex T3 instruction manual

Renault

Renault 77 11 423 180 Installation instruction

Kia

Kia E8300-4D000 manual

Brink

Brink 756843 installation instructions

Whispbar

Whispbar K085W Fitting instructions

v.link

v.link CI-VL2-PC-HSD manual

Viking

Viking Stack-Rack Assembly and use instructions

Aries

Aries 203015 installation manual

Choetech

Choetech AT0005 user manual

ZZ2

ZZ2 ZZAIR-PRO instruction manual

Holman

Holman 4A80L installation guide

Thule

Thule 2075 parts manual

Motorola

Motorola T325 quick start guide

TAUBENREUTHER

TAUBENREUTHER 16-3950 FITTING INSTRUCTION

DV8

DV8 FBJL-02 Product installation manual