Prorack K672 User manual
K672
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4 x 2 x 2 x 2
x 2 x 2 x 2 x 2
Revision No: 4D 1
Fitting Kit K672
MAX kgs (lbs)
W/P WHD
Kia
Grand Carnival , 5dr MPV 11-15 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
2
Fitting Kit EN
K672
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
3
Fitting Kit EN
K672
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
4
Fitting Kit EN
K672
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●A = Clear
B = Grey
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 272A
B = 273A
5
Fitting Kit EN
K672
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
6
Fitting Kit EN
K672
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
●Make sure the pad fits into the holes
underneath the foot.
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
7
Fitting Kit EN
K672
Fitment
●NOTE: REAR CROSSBAR ONLY
●Door seal has to be removed before
attaching fitting clips.
●Apply protective strip as shown.
●Press clip into place.
8
Fitting Kit EN
K672
●Clamp locates onto the body clip as shown.
All Crossbars:
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
●Repeat for all four positions.
9
Fitting Kit EN
K672
●Tighten locking screw on both legs evenly,
3 Nm (2.2 ft lb).
●Repeat for all four positions.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
10
This manual suits for next models
1
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K681 User manual
Prorack
Prorack K130 User manual
Prorack
Prorack K992 User manual
Prorack
Prorack K478 User manual
Prorack
Prorack K340 User manual
Prorack
Prorack K587 User manual
Prorack
Prorack Kayak Carrier User manual
Prorack
Prorack K129 User manual
Prorack
Prorack K621 User manual
Prorack
Prorack K301 User manual
Prorack
Prorack K373 User manual
Prorack
Prorack K991 User manual
Prorack
Prorack K585 User manual
Prorack
Prorack K595 User manual
Prorack
Prorack K381W User manual
Prorack
Prorack K598 User manual
Prorack
Prorack K907 User manual
Prorack
Prorack K1020 User manual
Prorack
Prorack K774 User manual
Prorack
Prorack K815 User manual
