Prorack K121 User manual
K121
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4 x 4 x 4 x 4
Revision No: 3C 1
Fitting Kit K121
MAX kgs (lbs)
W/P WHD
Nissan
Primera, 4dr Sedan 97-01 ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
Primera, 4dr Sedan Jul 97-01 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
2
Fitting Kit K121
X
A B C 1 2 3
Primera, 4dr Sedan 97-01 (ZA) -320mm 280mm - 776mm 758mm -
-12 -5/8ths" 11" - 30 9/16ths" 29 13/16ths" -
Primera, 4dr Sedan Jul 97-01 (NZ) -320mm 280mm - 776mm 758mm -
-12 -5/8ths" 11" - 30 9/16ths" 29 13/16ths" -
3
Fitting Kit EN
K121
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4
Fitting Kit EN
K121
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5
Fitting Kit EN
K121
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●A = Grey
B = Black
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
6
Fitting Kit EN
K121
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Fit rubber pads (supplied with fitting kit) to
foot.
●Make sure the pad fits into the holes
underneath the foot.
7
Fitting Kit EN
K121
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Clamps directly to edge of roof under the
doors
●Press adjusting screw to adjust the leg
positions on the crossbar.
8
Fitting Kit EN
K121
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
9
Fitting Kit EN
K121
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K783 User manual
Prorack
Prorack K672 User manual
Prorack
Prorack K661 Operation and installation manual
Prorack
Prorack K598 User manual
Prorack
Prorack K431 User manual
Prorack
Prorack K607 User manual
Prorack
Prorack K372 Operation and installation manual
Prorack
Prorack K108 User manual
Prorack
Prorack K1206 User manual
Prorack
Prorack K192 User manual
Prorack
Prorack K007 User manual
Prorack
Prorack K407 User manual
Prorack
Prorack K843 User manual
Prorack
Prorack K997 User manual
Prorack
Prorack K898 User manual
Prorack
Prorack K346 User manual
Prorack
Prorack K533 User manual
Prorack
Prorack K1104 User manual
Prorack
Prorack K115 User manual
Prorack
Prorack K834 User manual
