Prorack K587 User manual
K587
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4 x 2 x 1 x 1
x 2 x 2
Revision No: 2C 1
Fitting Kit K587
MAX kgs (lbs)
W/P WHD
BMW
3 Series E36, 4dr Sedan 91-98 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
3 Series E36, 4dr Sedan 91-98 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
3 Series E36, 4dr Sedan 91-98 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
3 Series E36, 4dr Sedan 91-98 ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
3 Series E36, 4dr Sedan 92-99 US 75 kgs (165 lbs) 75 kgs (165 lbs)
2
Fitting Kit EN
K587
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
3
Fitting Kit EN
K587
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment.
●Ensure each end of the crossbar is
adjusted equally.
4
Fitting Kit EN
K587
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 819A
B = 820A
5
Fitting Kit EN
K587
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
6
Fitting Kit EN
K587
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 11-04-243
B = 11-04-248
C = 11-04-249
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
●Make sure the pad fits into the holes
underneath the foot.
7
Fitting Kit EN
K587
Fitment
●Clamps directly to edge of roof under the
doors
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 5 Nm (3.7 ft lb).
8
Fitting Kit EN
K587
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
9
Fitting Kit EN
K587
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K324 User manual
Prorack
Prorack K677 Operation and installation manual
Prorack
Prorack K943 User manual
Prorack
Prorack K719 User manual
Prorack
Prorack K758 User manual
Prorack
Prorack K876 User manual
Prorack
Prorack S4 User manual
Prorack
Prorack K892 User manual
Prorack
Prorack K364 User manual
Prorack
Prorack K050 User manual
Prorack
Prorack K513 User manual
Prorack
Prorack K464 User manual
Prorack
Prorack K554 Operation and installation manual
Prorack
Prorack K564 User manual
Prorack
Prorack K471W User manual
Prorack
Prorack K827 User manual
Prorack
Prorack K426 User manual
Prorack
Prorack K704 User manual
Prorack
Prorack K381 User manual
Prorack
Prorack K376 User manual
