Prorack K827 User manual
K827
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 1 x 1 x 1
x 2 x 2
Revision No: 2A 1
Fitting Kit K827
MAX kgs (lbs)
W/P WHD
Hyundai
Genesis (Steel Roof), 4dr Sedan 14-+ CN 75 kgs (165 lbs) 75 kgs (165 lbs)
Genesis (Steel Roof), 4dr Sedan 15-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Genesis (Steel Roof), 4dr Sedan 15-+ US 75 kgs (165 lbs) 75 kgs (165 lbs)
Genesis (Steel Roof), 4dr Sedan 15-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
2
Fitting Kit K827
X
A B C 1 2 3
Genesis (Steel Roof), 4dr Sedan 14-+ (CN) -175mm 515mm - 896mm 878mm -
-6 -7/8ths" 20 1/4ths" - 35 1/4ths" 34 9/16ths" -
Genesis (Steel Roof), 4dr Sedan 15-+ (AU) -175mm 515mm - 896mm 878mm -
-6 -7/8ths" 20 1/4ths" - 35 1/4ths" 34 9/16ths" -
Genesis (Steel Roof), 4dr Sedan 15-+ (US) -175mm 515mm - 896mm 878mm -
-6 -7/8ths" 20 1/4ths" - 35 1/4ths" 34 9/16ths" -
Genesis (Steel Roof), 4dr Sedan 15-+ (NZ) -175mm 515mm - 896mm 878mm -
-6 -7/8ths" 20 1/4ths" - 35 1/4ths" 34 9/16ths" -
3
Fitting Kit EN
K827
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4
Fitting Kit EN
K827
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5
Fitting Kit EN
K827
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●A = Grey
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = A409
B = A410
C = A411
D = A412
6
Fitting Kit EN
K827
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
7
Fitting Kit EN
K827
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 296A
B = 295A
●Place rubber pads (supplied with fitting kit)
on the vehicle roof. Pad may vary in shape
to that shown.
●Make sure the pad fits into the holes
underneath the foot.
8
Fitting Kit EN
K827
Fitment
●Clamps directly to edge of roof under the
doors
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
9
Fitting Kit EN
K827
●Tighten locking screw on both legs evenly,
3 Nm (2.2 ft lb).
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
10
This manual suits for next models
1
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K199 User manual
Prorack
Prorack K813 User manual
Prorack
Prorack K571 Install guide
Prorack
Prorack K303 User manual
Prorack
Prorack K949 User manual
Prorack
Prorack K958 User manual
Prorack
Prorack K465 Operation and installation manual
Prorack
Prorack K781 User manual
Prorack
Prorack K456 User manual
Prorack
Prorack K601 User manual
Prorack
Prorack K681 User manual
Prorack
Prorack K104 User manual
Prorack
Prorack K719 User manual
Prorack
Prorack K112 User manual
Prorack
Prorack K042 User manual
Prorack
Prorack K564 User manual
Prorack
Prorack K677 Operation and installation manual
Prorack
Prorack PR3077 User manual
Prorack
Prorack K383 User manual
Prorack
Prorack K436 User manual
