Prorack K876 User manual
K876
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 1 x 1 x 1
x 2 x 1 x 1
Revision No: 1A 1
Fitting Kit K876
MAX kgs (lbs)
W/P WHD
Toyota
Yaris L, 5dr Hatch 13-+ CN 50 kgs (110 lbs) 50 kgs (110 lbs)
Yaris L, 5dr Hatch 13-+ EU 50 kgs (110 lbs) 50 kgs (110 lbs)
2
Fitting Kit K876
X
A B C 1 2 3
Yaris L, 5dr Hatch 13-+ (CN) -380mm 330mm - 797mm 742mm -
-14 -15/16ths" 13" - 31 3/8ths" 29 3/16ths" -
Yaris L, 5dr Hatch 13-+ (EU) -380mm 330mm - 797mm 742mm -
-14 -15/16ths" 13" - 31 3/8ths" 29 3/16ths" -
3
Fitting Kit EN
K876
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4
Fitting Kit EN
K876
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5
Fitting Kit EN
K876
●Remove locking screw.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = B523
B = B524
C = B525
D = B526
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
6
Fitting Kit EN
K876
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 241
B = 295
C = 296
7
Fitting Kit EN
K876
●Place rubber pads (supplied with fitting kit)
on the vehicle roof. Pad may vary in shape
to that shown.
●Make sure the pad fits into the holes
underneath the foot.
Fitment
●Clamps directly to edge of roof under the
doors
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
8
Fitting Kit EN
K876
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
●Tighten locking screw on both legs evenly,
2.5 Nm (1.8 ft lb).
9
Fitting Kit EN
K876
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K333 User manual
Prorack
Prorack K624 Operation and installation manual
Prorack
Prorack K094 User manual
Prorack
Prorack K042 User manual
Prorack
Prorack S17 User manual
Prorack
Prorack K411 User manual
Prorack
Prorack K569 User manual
Prorack
Prorack K317 User manual
Prorack
Prorack K528 User manual
Prorack
Prorack K707 User manual
Prorack
Prorack K1013 User manual
Prorack
Prorack K777 User manual
Prorack
Prorack K383 User manual
Prorack
Prorack K776 Operation and installation manual
Prorack
Prorack K345 User manual
Prorack
Prorack PR3077 User manual
Prorack
Prorack K091 User manual
Prorack
Prorack K823 User manual
Prorack
Prorack VOYAGER TRAY User manual
Prorack
Prorack K308 User manual
