Phytec PCM-995 User manual
A product of a PHYTEC Technology Holding company
Development Board for
phyCORE-MPC555
PCM-995
Hardware Manual
Edition November 2000
Development Board for phyCORE-MPC555
PHYTEC Meßtechnik GmbH 2000 L-525e_2
In this manual are descriptions for copyrighted products which are not explicitly
indicated as such. The absence of the trademark () symbol does not infer that a
product is not protected. Additionally, registered patents and trademarks are
similarly not expressly indicated in this manual
The information in this document has been carefully checked and is believed to be
entirely reliable. However, PHYTEC Meßtechnik GmbH assumes no responsibi-
lity for any inaccuracies. PHYTEC Meßtechnik GmbH neither gives any guarantee
nor accepts any liability whatsoever for consequential damages resulting from the
use of this manual or its associated product. PHYTEC Meßtechnik GmbH
reserves the right to alter the information contained herein without prior
notification and accepts no responsibility for any damages which might result.
Additionally, PHYTEC Meßtechnik GmbH offers no guarantee nor accepts any
liability for damages arising from the improper usage or improper installation of
the hardware or software. PHYTEC Meßtechnik GmbH further reserves the right
to alter the layout and/or design of the hardware without prior notification and
accepts no liability for doing so.
Copyright 2000 PHYTEC Meßtechnik GmbH, D-55129 Mainz. Rights -
including those of translation, reprint, broadcast, photomechanical or similar
reproduction and storage or processing in computer systems, in whole or in part -
are reserved. No reproduction may occur without the express written consent from
PHYTEC Meßtechnik GmbH.
EUROPE NORTH AMERICA
Address: PHYTEC Technologie Holding AG
Robert-Koch-Str. 39
D-55129 Mainz
GERMANY
PHYTEC America LLC
255 Ericksen Avenue NE
Bainbridge Island, WA 98110
USA
Ordering
Information: +49 (800) 0749832
Technical
Support: +49 (6131) 9221-31
Fax: +49 (6131) 9221-33 +1 (206) 780-9135
Web Site: http://www.phytec.de http://www.phytec.com
2nd Edition November 2000
Contents / Table of figures
PHYTEC Meßtechnik GmbH 2000 L-525e_2
Preface...........................................................................................................1
1 Introduction .........................................................................................3
1.1 Development Board Block Diagram ............................................5
1.2 Overview of the Development Board...........................................6
2 Development Board Connectors ........................................................7
2.1 Power Connectors X5...................................................................9
2.1.1 Connection via the Low Voltage Socket X5...................9
2.2 DB-25 socket P1 – BDM Interface.............................................11
2.3 DB-9 sockets P2 and P3 – RS-232 Interfaces ............................11
2.4 DB-9 plugs P4 and P5 – CAN Interfaces ...................................12
2.5 VG-96 I/O-Connector VG1........................................................13
3 Jumper Layout...................................................................................15
3.1 BDM interface JP1, JP2, JP5 to JP9, JP17................................17
3.2 Reset-Push-Button JP3 ..............................................................18
3.3 Target configuration JP4, JP15, JP16........................................19
3.4 Supply Voltages JP10 to JP12, J1..............................................20
3.5 Interrupt-Push-Button JP18.......................................................21
3.6 CAN bus termination JP13 and JP14.........................................22
3.7 Default Jumper Configurations overview...................................23
4 Technical Specifications....................................................................25
Index............................................................................................................27
Development Board for phyCORE-MPC555
PHYTEC Meßtechnik GmbH 2000 L-525e_2
Index of figures and tables
Figure 1: Block Diagram of the Development Board..................................5
Figure 2: Development Board Overview (component side)........................6
Figure 3: Location of the Connectors ..........................................................8
Figure 4: Polarity of the Power Connector at X5.......................................10
Figure 5: Pinout of DB-9 socket P2 (front view).......................................11
Figure 6: Pinout of DB-9 socket P3 (front view).......................................11
Figure 7: Pinout of the DB-9 plug at P4 (front view)................................12
Figure 8: Pinout of the DB-9 plug at P5 (front view)................................12
Figure 9: Numbering of the Jumper-pads..................................................15
Figure 10: Location of the Jumpers (top side).............................................15
Figure 11: Default Jumper Configuration....................................................23
Figure 12: Physical Dimensions...................................................................25
Table 1: Pinout of the I/O connector VG1 ...............................................13
Preface
PHYTEC Meßtechnik GmbH 2000 L-525e_2 1
Preface
This manual describes only the functions of the PHYTEC
Development Board. The controllers and relevant Single Board
Computers for use with the Development Board are not described
herein. Additional controller- and board-level information and
technical descriptions can be found in appropriate Hardware Manual
or User’s Manual support documentation. If software is included
please also refer to additional documentation for this software.
In this hardware manual and in the attached schematics, low active
signals are denoted by a "/" in front of the signal name (i.e.: /RD). A
"0" indicates a logic-zero or low-level signal, while a "1" represents a
logic-one or high-level signal.
Declaration regarding EMV-Conformity of the
PHYTEC Development Board
PHYTEC Development Boards (henceforth „products“) are designed
for installation in electrical appliances or as dedicated Evaluation
Boards (i.e.: for use as a test and prototype platform for
hardware/software development) in laboratory environments.
Attention:
PHYTEC products lacking protective enclosures are subject to
damage by ESD and, hence, may only be unpacked, handled or
operated in environments in which sufficient precautionary measures
have been taken in respect to ESD-dangers. It is also necessary that
only appropriately trained personnel (such as electricians, technicians
and engineers) handle and/or operate these products. Moreover,
PHYTEC products should not be operated without protection circuitry
if connections to the product's pin header rows are longer than 3 m.
Development Board for phyCORE-MPC555
2PHYTEC Meßtechnik GmbH 2000 L-525e_2
PHYTEC products fulfil the norms of the EMVG-statute only in
accordance to the descriptions and rules of usage indicated in this
hardware manual (particularly in respect to the pin header row
connectors, power connector and serial interface to a host-
PC).Implementation of PHYTEC products into target devices, as well
as user modifications and extensions of PHYTEC products, is subject
to renewed establishment of conformity to, and certification of, EMV-
Statutes. Only after doing so the devices are allowed to be put into
circulation.
PHYTEC supports all common 8-, 16- and 32-bit controllers in two
ways:
(1) as the basis for Rapid Development and Starter Kits in which
user-designed hardware can be implemented on a wrap-field
around the controller and
(2) as insert-ready, fully functional Single Board Computer
modules which can be embedded directly into the user’s
peripheral hardware design.
PHYTEC’s microcontroller modules allow engineers to shorten
development horizons, reduce design costs and speed project
concepts from design to market. Please contact PHYTEC for
additional information:
EUROPE NORTH AMERICA
Address: PHYTEC Technologie
Holding AG
Robert-Koch-Str. 39
D-55129 Mainz
GERMANY
PHYTEC America LLC
255 Ericksen Avenue NE
Bainbridge Island, WA 98110
USA
Web Site: http://www.phytec.de http://www.phytec.com
e-mail: [email protected] info@phytec.com
Voice: +49 (6131) 9221-0 +1 (800) 278-9913
Fax: +49 (6131) 9221-33 +1 (206) 780-9135
Introduction
PHYTEC Meßtechnik GmbH 2000 L-525e_2 3
1Introduction
The PHYTEC phyCORE Development Board, in EURO-card
dimensions (160 x 100 mm.), is a universal carrier board for start-up
and programming of the PHYTEC phyCORE-MPC555 Single Board
Computer module with two high density SMT (160 pins each, 0.63
mm. pitch) pin header connectors. The Development Board is fully
equipped with all mechanical and electrical components necessary for
the speedy and secure insertion and subsequent programming of the
high density PHYTEC phyCORE module. These components include
DB-9, DB-25, VG-96 and power socket connectors. The phyCORE
module can be plugged like a “big chip” onto the Development
Board’s pin header receptacles. Once programmed, the phyCORE
module can be removed from the Development Board and inserted
like a “big chip” in a target hardware application.
The following phyCORE Single Board Computer modules can be
used in conjunction with the Development Board:
•phyCORE-MPC555
The hardware manual for this Development Board does not describe
in detail the features of the phyCORE modules, which are not relevant
for the basic functioning of the Development Board. For module and
controller-specific features please refer to the corresponding hardware
manuals/User’s Manuals.
Development Board for phyCORE-MPC555
4PHYTEC Meßtechnik GmbH 2000 L-525e_2
The Development Board offers the following features:
•Reset push-button, configurable via jumper for different Reset
signals
•IRQ push-button, configurable via jumper for different interrupts
•Wake-Up push-button
•Boot jumper to select internal or external FLASH memory
•Jumper to enable the programming voltage for internal FLASH
memory
•Reset jumper to choose between internal and external Reset
configuration
•two software programmable LED’s (red/green)
•LED’s for power monitoring
•LED to monitor debug or run mode
•power supply for unregulated input voltage from 7 V to 13 V. It
supplies regulated +5V, +3.3V for the phyCORE-MPC555.
Additional +5V is created for the VG96-connector.
•VG-96 connector with all I/O-signals of the MPC555
•two standard width pin header rows (3x54) which provide all
phyCORE-MPC555 signals
•two DB-9 sockets for RS-232 interface
•two DB-9 plugs for two separate CAN interfaces with configurable
terminating resistors
•DB-25 plug for BDM interface to support direct connection to PC
printer-port
•2 x 5 standard width pin header rows to support other BDM-
interfaces
Introduction
PHYTEC Meßtechnik GmbH 2000 L-525e_2 5
1.1 Development Board Block Diagram
terminator
terminator
all reset signals
j
umper field
j
umper field
phyCORE-
connector
TPU, MDA,
ADC, QGPIO,
RS232, IRQ
MPIO1
MPIO0
power control
5V
3.3V
5V
7..13V DC VG96
connector
Extension connector
6x54 pin
2.54 mm width
BDM-interface
DB25
debug/run
PC
printer port
DSUB-P2
all signals of
phyCORE -
connector X1
/IRQ[0..7]
LED
D8
LED
D9
LED
D10
Reset
Switch S2
IRQ
Switch S5
Wake-UP
Switch S1
LED
D11
LED
D4 LED
D5
CAN_0
RS232_0
RS232_1
CAN_1
DSUB-P5DSUB-P4DSUB-P3
power connector
Figure 1: Block Diagram of the Development Board
Development Board for phyCORE-MPC555
6PHYTEC Meßtechnik GmbH 2000 L-525e_2
1.2 Overview of the Development Board
Figure 2: Development Board Overview (component side)
Table of contents
Other Phytec Motherboard manuals
Phytec
Phytec phyFLEX-i.MX 6 Programming manual
Phytec
Phytec phyCORE-OMAP44 Series Programming manual
Phytec
Phytec phyCORE-TC1775 User manual
Phytec
Phytec kitCON-161CS User manual
Phytec
Phytec phyCORE-LPC2294 Programming manual
Phytec
Phytec phyBOARD RANA-AM335x User manual
Phytec
Phytec phyCORE-XC161 Programming manual
Phytec
Phytec phyBOARD Wega AM335 Series User manual
Phytec
Phytec phyCORE-LPC2292/94 User manual
Phytec
Phytec phyCORE-TriCore User manual
Phytec
Phytec phyCORE-ADuC812 User manual
Phytec
Phytec phyBOARD Regor AM335x User guide
Phytec
Phytec phyCORE-i.MX 6 User manual
Phytec
Phytec phyBOARD-Wega-AM335x User manual
Phytec
Phytec phyCORE-MPC565 Programming manual
Phytec
Phytec phyCORE-i.MX27 User manual
Phytec
Phytec phyBOARD-Wega AM335x User manual
Phytec
Phytec phyBOARD WEGA-AM335x User manual
Phytec
Phytec phyCORE-P87C591 Programming manual
Phytec
Phytec phyCORE-i.MX35 User manual
