Phytec PhyCORE-MPC565 Programming manual

A product of a PHYTEC Technology Holding company

QuickStart Instructions

phyCORE-MPC565

Using Freescale CodeWarrior

Development Tool Chain

Note: The PHYTEC Spectrum CD includes the electronic version of

the phyCORE-MPC565 English Hardware Manual

Edition: September 2009

phyCORE-MPC565 QuickStart Instructions

In this manual are descriptions for copyrighted products that are not explicitly

indicated as such. The absence of the trademark (™) and copyright (©) symbols

does not imply that a product is not protected. Additionally, registered patents and

trademarks are similarly not expressly indicated in this manual.

The information in this document has been carefully checked and is believed to be

entirely reliable. However, PHYTEC Meßtechnik GmbH assumes no

responsibility for any inaccuracies. PHYTEC Meßtechnik GmbH neither gives

any guarantee nor accepts any liability whatsoever for consequential damages

resulting from the use of this manual or its associated product. PHYTEC

Meßtechnik GmbH reserves the right to alter the information contained herein

without prior notification and accepts no responsibility for any damages which

might result.

Additionally, PHYTEC Meßtechnik GmbH offers no guarantee nor accepts any

liability for damages arising from the improper usage or improper installation of

the hardware or software. PHYTEC Meßtechnik GmbH further reserves the right

to alter the layout and/or design of the hardware without prior notification and

accepts no liability for doing so.

Rights - including those of translation, reprint, broadcast, photomechanical or

similar reproduction and storage or processing in computer systems, in whole or

in part - are reserved. No reproduction may occur without the express written

consent from PHYTEC Meßtechnik GmbH.

EUROPE NORTH AMERICA

Address: PHYTEC Technologie Holding AG

Robert-Koch-Str. 39

D-55129 Mainz

GERMANY

PHYTEC America LLC

203 Parfitt Way SW, Suite G100

Bainbridge Island, WA 98110

USA

Ordering

Information: +49 (800) 0749832

[email protected] 1 (800) 278-9913

[email protected]

Technical

Support: +49 (6131) 9221-31

[email protected] 1 (800) 278-9913

[email protected]

Fax: +49 (6131) 9221-33 1 (206) 780-9135

Web Site: http://www.phytec.de http://www.phytec.com

2nd Edition: September 2009

Contents

1 Introduction to the phyCORE-MPC565

Rapid Development Kit......................................................................1

1.1 Rapid Development Kit Documentation......................................1

1.2 Overview of this QuickStart Instruction......................................2

1.3 System Requirements...................................................................2

1.4 The PHYTEC phyCORE-MPC565 .............................................4

1.5 The Metrowerks CodeWarrior Development Tool Chain ...........8

2 Getting Started..................................................................................13

2.1 Installing the Metrowerks CodeWarrior Tool Chain.................13

2.2 Installing Rapid Development Kit Software..............................15

2.3 Interfacing the phyCORE-MPC565 to a Host-PC.....................15

2.4 Launching the CodeWarrior IDE...............................................19

2.4.1 Setting up a New Remote Connection..........................19

2.5 Downloading Example Code with CodeWarrior IDE ...............22

2.5.1 Configuring HyperTerminal Program for Hello_Fl

example .........................................................................22

2.5.2 Running the Hello_Fl.mcp Demo Project in RAM ......25

2.5.3 Downloading Hello_Fl to the MPC565

On-Chip Flash...............................................................32

2.5.4 Downloading Hello_Fl to the External Standard

Flash (PCM-019-1010E Only)......................................39

2.5.5 Downloading Hello_Fl to the External Burst Flash

(PCM-019-3230 Only)..................................................46

2.6 Creating a New Project ..............................................................54

Figures

Figure 1: Freescale CodeWarrior IDE Architecture..................................9

Figure 2: Development Board Overview ................................................16

Figure 3: Default Jumper Settings of the phyCORE Development Board

PCM-991 with phyCORE-MPC565........................................17

Figure 4: Power Connector......................................................................18

phyCORE-MPC565 QuickStart Instructions

Introduction to the phyCORE-MPC565

1Introduction to the phyCORE-MPC565 Rapid

Development Kit

This QuickStart provides:

•general information on the PHYTEC phyCORE-MPC565 Single

Board Computer

•an overview of Freescale's CodeWarrior software development

tool chain, and

•instructions on how to run example programs on the

phyCORE-MPC565, mounted on the PHYTEC Development

Board, in conjunction with Freescale' CodeWarrior tools.

Please refer to the phyCORE-MPC565 Hardware Manual for specific

information on such board-level features as jumper configuration,

memory mapping and pin layout. Selecting the links on the electronic

version of this document links to the applicable section of the

phyCORE-MPC565 Hardware Manual.

1.1 Rapid Development Kit Documentation

This "Rapid Development Kit" includes the following electronic

documentation on the enclosed "PHYTEC Spectrum CD-ROM":

•PHYTEC phyCORE-MPC565 Hardware Manual and

Development Board Hardware Manual

•PHYTEC phyCORE-MPC565 QuickStart Instructions

•MPC565 controller User's Manuals and Data Sheets

phyCORE-MPC565 QuickStart Instructions

2© PHYTEC Meßtechnik GmbH 2009 L-647e_2

1.2 Overview of this QuickStart Instruction

This QuickStart Instruction provides a general "Rapid Development

Kit" description, software installation hints, and example programs

enabling quick out-of-the box start-up of the

phyCORE-MPC565 in conjunction with Freescale's CodeWarrior

tools. The "Getting Started"section uses the example program

"Hello_Fl" to demonstrate the download of user code to the

phyCORE-MPC565 external RAM, internal Flash, and external Flash,

using Freescale CodeWarrior Debugger and Flash Programmer. This

section also provides hints for creating a new

phyCORE-MPC565 project in Freescale's CodeWarrior.

1.3 System Requirements

Use of this "Rapid Development Kit" requires:

•the PHYTEC phyCORE-MPC565,

•the PHYTEC Development Board with the included DB-9 serial

cable, DB-25 printer port cable and AC-to-DC adapter supplying

5 V DC/min. 1.5 A,

•the PHYTEC Spectrum CD,

•the Freescale CodeWarrior CD (the required evaluation license key

needs to be requested from Freescale using the integrated

registration wizard),

•an IBM-compatible host-PC (Pentium II or higher) running

Microsoft Windows 2000/XP or Windows NT (Service Pack 6a or

later), and 300 MB hard disk space plus project space.

Introduction to the phyCORE-MPC565

For more information and example updates, please refer to the

following sources:

http://www.phytec.com - or - http://www.phytec.de

[email protected] - or - [email protected]

http://www.freescale.com/

phyCORE-MPC565 QuickStart Instructions

4© PHYTEC Meßtechnik GmbH 2009 L-647e_2

1.4 The PHYTEC phyCORE-MPC565

The phyCORE-MPC565 module integrates the 32-bit Freescale

MPC565 PowerPC microcontroller on an advanced PCB layout. All

applicable controller signals extend to two 200-pin, high-density

Molex connectors. In addition to the on-chip Flash (1 MByte), the

phyCORE-MPC565 can be populated with up to 8 MByte of

asynchronous standard Flash and up to 16 MByte of synchronous

Burst-SRAM, addressable without wait states. Both memory device

types support of the fastest interface mode of the MPC565, thereby

guaranteeing maximized processing speed of externally stored code

and data. The internal and external Flash supports direct on-board

programming without additional programming voltages. A serial

EEPROM (up to 32 KByte) is available for storing operating

parameters. A Real-Time Clock with a calendar and alarm function

serves as a real-time reference.

The phyCORE-MPC565 is especially suited for applications requiring

processing of calculation-intensive algorithms. The MPC565's

integrated 64-bit Floating Point Unit (FPU) enables hardware-level

execution of elementary operations with single or double precision

floating point numbers. Other controller features supported by the

SBC module include three on-chip CAN 2.0B controllers; four

UARTs; two SPI and one J1850 interfaces; dual 10-bit A/D with

40 (56) channels; twelve 16-bit PWM systems and three Time

Processing Units (TPU) that process microcode independently of the

PowerPC core. The MPC565 provides enhanced operational flexibility

in that it can manage complex control and regulation tasks without

connection to any peripheral devices. Each TPU has 16 programmable

channels (pins) that route data to and from peripheral features,

enabling generation of extremely complex timings without burdening

user code. This flexibility allows implementation of the phyCORE-

MPC565 in a wide range of embedded applications.

Introduction to the phyCORE-MPC565

phyCORE-MPC565 Technical Highlights

•Single Board Computer in subminiature form factor (84 x 57 mm)

according to phyCORE specifications

•all applicable controller and other logic signals extend to two

high-density 200-pin Molex connectors

•Freescale embedded PowerPC MPC565 (40/56 MHz clock)

•Internal Features of the MPC565:

- 32-bit PowerPC core, 40 / 56 MHz CPU speed

- 64-bit Floating Point Unit

- 36 kByte SRAM; capable of battery buffering

- 1 MByte Flash (two independent 512 kByte blocks)

-four UARTs

-two SPI interfaces and one J1850 interface

- three CAN 2.0B interfaces

- three TPU with 16 channels each

-six 16-bit timer systems (MOIS14)

-twelve 16-bit PWM systems (MIOS14)

- dual 10-bit ADC (5µs) with 40 (65) channels (ext. MUX)

-multi-purpose I/O signals

-JTAG/BDM/Nexus test/debug port

•Memory Configuration1:

- SRAM: 1 MByte to 16 MByte flow-through

synchronous burst-RAM, 32-bit access,

0 wait states, 2-1-1-1 burst mode

- Flash-ROM: 2/4 MB synchronous burst mode

Flash-EEPROM, 32-bit access

2 MByte to 8 MByte asynchronous

standard Flash-EEPROM, 32-bit access

- I2C Memory: 4 kByte EEPROM (up to 32 kByte, alter-

natively I2C FRAM, I2C SRAM)

•Other Board-Level Features:

1: Please contact PHYTEC for more information about additional module configurations.

phyCORE-MPC565 QuickStart Instructions

6© PHYTEC Meßtechnik GmbH 2009 L-647e_2

•UART port: two RS-232 transceivers for channel A and

B (RxD/TxD); also configurable as TTL

•CAN port: two CAN transceivers 82C251 for channels

A and B; also configurable as TTL

•Ethernet port: 10 MBit/s CS8900A controller (I/O mode)

•System-EPLD: Lattice device ispMACH LC4064,

in-system programmable, 10 free I/O

signals, e.g. for additional /CS generation

•I2C Real-Time Clock with calendar and alarm function

•power-down/wake-up support via RTC or external signal

•JTAG/BDM/Nexus test/debug port

•industrial temperature range (-40…+85°C)

The phyCORE-MPC565 Development Board is fully equipped with

all mechanical and electrical components necessary for the speedy and

secure insertion and subsequent programming of the

phyCORE-MPC565 module with high-density (0.635 mm pitch) pin

header connectors. RS-232 and CAN interface signals extend from

the module to dual-stacked DB-9 connectors on the Development

Board, while Ethernet signals extend to an RJ-45 connector. A 40-pin

Nexus connector provides a debugging interface (an unpopulated

50-pin Nexus connector is also available).

Table of contents

Other Phytec Motherboard manuals

Phytec

Phytec phyCORE-XC161 Programming manual

Phytec

Phytec phyCORE-TC1775 User manual

Phytec

Phytec phyBOARD-Wega-AM335x User manual

Phytec

Phytec phyCORE-MPC5554 User manual

Phytec

Phytec PhyBOARD-WEGA-AM335 SERIES User manual

Phytec

Phytec phyCORE-PXA255 User manual

Phytec

Phytec phyCORE-i.MX27 User manual

Phytec

Phytec phyCORE-LPC2292/94 User manual

Phytec

Phytec phyCORE-AM335x User manual

Phytec

Phytec PCM-995 User manual

Phytec

Phytec phyCORE-LPC2294 Programming manual

Phytec

Phytec phycore i.mx7 User manual

Phytec

Phytec phyCORE-TriCore User manual

Phytec

Phytec phyBOARD WEGA-AM335x User manual

Phytec

Phytec phyFLEX-i.MX 6 Programming manual

Phytec

Phytec phyBOARD Wega AM335 Series User manual

Phytec

Phytec phyBOARD-Wega AM335x User manual

Phytec

Phytec L-1008e.A0 phyCORE-i.MX 8M Plus Alpha Kit User manual

Phytec

Phytec phyBOARD-Subra-i.MX6 User manual

Phytec

Phytec PhyBOARD-Mira i.MX6 User manual

Phytec

Phytec phyCORE-P87C591 Programming manual

Phytec

Phytec phyCORE-i.MX 6 User manual

Phytec

Phytec phyCORE-MPC5200B tiny Programming manual

Phytec

Phytec phyCORE-i.MX35 User manual

Popular Motherboard manuals by other brands

DFI

DFI SD170 user manual

ASROCK

ASROCK ROMED8-2T user manual

Asus

Asus P2L97A user manual

Winmate

Winmate IC70 user manual

Asus

Asus MES-B user manual

Grantech

Grantech SYS8F377VGGA-3OMN user manual

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR user guide

Gigabyte

Gigabyte GA-9IVDT user manual

Texas Instruments

Texas Instruments ADS8372EVM user guide

Commell

Commell MS-C73 user manual

IBT Technologies

IBT Technologies MB860 user manual

Nvidia

Nvidia TEGRA DG-04927-001_V01 user guide

Biostar

Biostar M7VIT Bravo Description

Intel

Intel D33217CK specification

Asus

Asus F1A55-M LX PLUS R2.0 user manual

EPC

EPC EPC9147C quick start guide

Asus

Asus EX-B760M-V5 D4 quick start guide

EPOX

EPOX MU-8KHA0010 user manual

Phytec phyCORE-MPC565 Programming manual

Popular Motherboard manuals by other brands