PEERLESS Solid-Point PS 1 Guide
1 of 6 ISSUED: 07-03-02 SHEET #: 200-9386-6 01-25-11
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
L
EG
Installation&Assembly -Solid•Point™Wall Mountwith TiltandSwivel
IMPORTANT! Read entire instruction sheet before you start assembly and installation.
Model:PS1
Place swivel lock bracket (I) on wall arm assembly (J)
as shown to the right.
Place rotation box (A) with threaded holes up over
wall arm assembly (J). Insert tilt pivot retainer
assembly (B) through rotation box (A) and wall arm
assembly (J).
Secure rotation box (A) to swivel lock bracket (I) using
four M5 x .8 x 10 mm phillips screws (H). Align holes
in tilt pivot retainer assembly (D) with holes in rotation
box (B) and secure with two 10-32 x 1/2" socket pin
screws (C) as shown.
Before you start make sure all parts
listed are included with your product.
PART # QTY. DESCRIPTION
A200-1434 1 rotation box
B200-1877 1 tilt pivot retainer assembly
C520-1055 2 10-32 x 1/2" socket pin screw
D200-0288 1 pitch roll assembly
E520-1001 1 carriage bolt 3/8"-16 x 3"
F520-9263 12 M10 x 1.5 x 15 mm penta-pin screw
G590-1087 1 tilt adjustment knob
H520-9250 4 M5 x .8 x 10 mm phillips screw
I200-1311 1 swivel lock bracket
J200-0342 1 wall arm assembly
K520-9260 1 M10 x 2" penta-pin™driver
L200-1338 1 wall plate
M590-0097 4 concrete anchor
N540-1008 4 fender washer
O5SI-015-C03 4 wood screw
P560-9646 1 4 mm security allen wrench
Parts List
Note: Some parts may appear slightly different than illustrated.
A
D
C
F
B
I
A
J
B
C
I
H
THREADED
HOLES
A
B
I
Note: Lay flat on sufrace for ease of assembly.
J
I
J
Hole in bottom of
rectangular tube
denotes bottom of
wall arm assembly.
K
J
H
N
O
M
P
2 of 6 ISSUED: 07-03-02 SHEET #: 200-9386-6 01-25-11
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
M5 SCREW
SLOT
RETAINING
SPACER
BRACKET
VERTICAL
POSITION
OPTIONAL:
PLASMA IN VERTICAL POSITION
HORIZONTAL
POSITION
TILTBRACKET
BRACKET
M5 SCREWS
CENTER
BOLT
Insert and tape carraige bolt (E) into top hole
of pitch roll assembly (D). Attach pitch roll
assembly (D) to adapter bracket with four M10
penta-pin screws (F). Tighten M10 screws
with penta-pin driver (K).
Note: Adapter bracket may be ordered
separately and will vary in size and style.
D
GENERIC
ADAPTER
BRACKET
TILTBRACKET
CENTER
BOLT
GENERIC ADAPTER BRACKET
RETAINING
SPACER
WASHER
SLOT
M5 SCREW
BRACKET
CARRIAGEBOLT
DETAIL 4
DO NOT REMOVE M5 SCREWS. Forverticalorientation,
unscrew two M5 screws until screw is able to move
freely in slot of tilt bracket as shown in details 4 and 4A.
Hold adapter bracket stationary and rotate tilt bracket
90° by hand or using a lever (example: wood 2 x 4).
Align M5 screws with threaded holes on bracket and
tighten two M5 screws back into bracket.
E
DETAIL 4A
M5 SCREW
WASHER
THREADED
HOLE
F
GENERIC
ADAPTER
BRACKET
NOTE: Refer to adapter plate instruction sheet (not included
with PS-1) for attachment of adapter plate to plasma before
proceeding with step 2.
• Donot overtightenscrews.Overtightening mayhinder
rolloption.
CAUTION
3 of 6 ISSUED: 07-03-02 SHEET #: 200-9386-6 01-25-11
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
L
O
N
L
Use stud finder to locate stud centers. Place wall plate
(L) on wall as template, level wall plate and mark center
of studs with pencil. The wall plate can be mounted on
16" centers. When mounted to 16" studs, the wall plate
can be shifted 4" left or right of center if desired.
Note: Hardware provided is for attachment of plasma mount
through standard thickness drywall or plaster into wood studs.
Installers are responsible to provide hardware for other types of
mounting situations.
For Wood Stud Walls drill four 5/32" (4 mm) dia. holes 2 1/2" (65
mm) deep. Attach wall plate (L) using four #14 x 2.5" (6 mm x 65
mm) wood screws and washers (O & N).
CONCRETE/CINDER BLOCKINSTALLATION
Place wall plate (L) on wall as template, level
wall plate and mark center of slots with pencil. L
• Tighten wood screws so that wall plate is firmly
attached,but do notovertighten.Overtighteningcan
damagescrews,greatly reducingtheirholding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the
center of the studs. The use of an "edge to edge" stud
finderis highly recommended.
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1 5/8" of actual concrete
surface in the 1/4" diameter hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to
mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM
C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of
ahammerdrill to avoid breakingoutthe back of theholewhenentering a void orcavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support 4 times the combined load of the equipment and all attached hardware
andcomponents.
WARNING
4 of 6 ISSUED: 07-03-02 SHEET #: 200-9386-6 01-25-11
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
For Concrete Walls drill four 1/4" (6 mm) dia. holes to a
minimum depth of 2.5" (64 mm) on marks made in step
1. Insert anchor (M) in holes flush with wall as shown
(right). Place wall plate (L) over anchor and secure with
four #14 x 2.5" (6 mm x 65 mm) wood screws and
washers (O & N) as shown at bottom of page. Make sure
wall plate is level before placing fasteners. Tighten all
fasteners.
CUTAWAYVIEW
1
3
2
Drill holes and insert anchors (M) in four places
Level wall plate and tighten four screws (O).
Place wall plate (L) over anchors (M) and fasten
with screws (O) and washers (N). Do not tighten.
concrete
N
OL
M
M
NOTE:Fivemountingpositions,centerpositionshown
totheright.
Attach wall arm assembly (J) to wall plate (L) using four
M10 penta-pin screws (F).
L
J
F
O
L
O
N
• Always attach concrete expansion anchors directly to
load-bearingconcrete.
• Neverattachconcrete expansionanchorsto concrete
coveredwithplaster, drywall,or other finishingmaterial.
WARNING
• Tighten wood screws so that wall plate is firmly
attached,but do notovertighten. Overtighteningcan
damagescrews,greatly reducingtheirholding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING
5 of 6 ISSUED: 07-03-02 SHEET #: 200-9386-6 01-25-11
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
Insert two M10 penta-pin screws (F) into rotation box
(A) as shown. Leave approx. 1/4” of exposed thread.
Hook pitch roll assembly (D) onto M10 penta-pin screws (F). Insert carraige bolt (E) into slot
of tilt pivot retainer assembly (B) as shown. Install tilt adjustment knob (G).
Install remaining two M10 penta-pin screws (F). HAND TIGHTEN all four M10 penta-pin
screws (F) to allow for tilt adjustment. Remove tape from carriage bolt (E). For tilt adjustment,
gently push back on the top of plasma to relieve pressure on knob. Adjust tilt to desired
position and tighten tilt adjustment knob (G), then securely tighten all four M10 screws (F)
using penta-pin driver (K).
ASAFINALPRECAUTION,CHECKALLFASTENERSANDTIGHTENSECURELY.
A
DBE
F
F
GG
.25" F
E
F
• Always use an assistant or mechanical lifting equip-
ment to safely lift and position the plasma television.
WARNING
6 of 6 ISSUED: 07-03-02 SHEET #: 200-9386-6 01-25-11
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
Depending on the specific size & weight of the plasma, plasma may appear to lean sideways. Pitch roll assembly (D)
allows plasma to be manually adjusted, so plasma can be horizontal. To adjust, gently rotate plasma by hand to desired
position.
IMPORTANT! Center bolt is factory torqued for optimal performance to adjust for range of plasma sizes.
If it is too difficult to adjust roll of plasma, torque may be adjusted by following the procedures below.
Adjust tilt adjustment knob (G) to allow maximum tilt.
Insert 3/4" open-end wrench (not provided) into side of pitch roll assembly (D) and rotate center bolt counter-
clockwise to loosen torque.
IMPORTANT! Do not loosen or tighten more than 1/8 turn.
CENTER
BOLT
PLASMA
A
D
ADAPTER
PLATE
PLASMA
D
CENTER
BOLT
WRENCH
G
NOTE: Refer to page four of accompanying instruction sheet for attachment of PS 1 with plasma to wall
plate before proceeding with step 4.
©2004PeerlessIndustries,Inc. Allrightsreserved.
PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
Other PEERLESS Rack & Stand manuals
PEERLESS
PEERLESS PRG-1 Guide
PEERLESS
PEERLESS VPM 25-J Guide
PEERLESS
PEERLESS DST360 Guide
PEERLESS
PEERLESS WBK100-W Guide
PEERLESS
PEERLESS PM 47 Guide
PEERLESS
PEERLESS Smartmount ST670 Guide
PEERLESS
PEERLESS SR1G Guide
PEERLESS
PEERLESS Vision Point LCFS 100 Guide
PEERLESS
PEERLESS Paramount PT650 Guide
PEERLESS
PEERLESS SmartMount RTFPA45 Guide
PEERLESS
PEERLESS WSP700 Instruction Manual
PEERLESS
PEERLESS SmartMount SP850-UNL Guide
PEERLESS
PEERLESS A100IWBMOUNT Guide
PEERLESS
PEERLESS DS-VW660 and assembly Guide
PEERLESS
PEERLESS SmartMount SP740P Guide
PEERLESS
PEERLESS DS246 Guide
PEERLESS
PEERLESS AEC0609 Guide
PEERLESS
PEERLESS ACC605 Guide
PEERLESS
PEERLESS PARAMOUNT PA730 Instruction Manual
PEERLESS
PEERLESS LMAM1940 Guide
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
