PEERLESS SR1G Guide

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07

Installation and Assembly: 32" - 60" Flat Panel TV Cart

Models: SR1G, SR560G

Max UL Load Capacity:

150 lb (68 kg) screen

50 lb (22.7 kg) per shelf

This product is UL Listed. It must be

installed by a qualified professional

installer.

2 of 14 ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07

Note: Read entire instruction sheet before you start installation and assembly.

• DonotbegintoinstallyourPeerlessproductuntilyouhavereadandunderstoodtheinstructionsandwarnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please

callPeerlesscustomercareat1-800-729-0307.

• Thisproduct should only be installed by someone of good mechanical aptitude, and fullyunderstands

these instructions.

• Neverexceed the Maximum ULLoadCapacity.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tightenscrews firmly, but do notovertighten.Overtightening can damage the items,greatlyreducing their holding

power.

• The cart is not affixed or secured to the floor, and may therefore tip over and/or fall if screen and/or stand is shaken

or hit.Always monitor children and do not let children play alone around stand as they could get hurt by a falling

screen.Notrecommended for use in areas with heavy traffic.

WARNING

Table of Contents

Parts List......................................................................................................................................................................3, 4, 5

AssemblingCart ...................................................................................................................................................................5

AttachingScreenUsingUniversalPlatewithAdapterBrackets .............................................................................................. 10

AttachingScreen with VESA 100 Mounting Pattern...............................................................................................................13

AttachingScreen Usinga DedicatedPlate ............................................................................................................................14

Tools Needed for Assembly

•level

•phillipsscrewdriver

3 of 14 ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07

Parts List

SR1G SR560G

Black Black

Description Qty. Part Number Part Number

Ascreen mount bracket 1 201-1156 201-1156

Bhook plate 1 201-1157 201-1157

Cshelf support 1 201-1158 201-1158

Dshelf clamp bracket 1 201-1159 201-1159

Ebase 1 009-1223 009-1223

Funiversal plate 1 N/A 201-1110

G adapter bracket 2 N/A 200-0752

Hupright 1 580-1180 580-1180

Iglass shelf 1 590-1208 590-1208

Jtop cover 1 590-1210 590-1210

Kbutton bumper 9 590-1209 590-1209

L1/4-20 x 12mm decorative screw 14 520-2325 520-2325

M1/4-20mm nut 12 530-1022 530-1022

N5/16" flat washer 10 540-9406 540-9406

O3/8-16 x 2.5" socket screw 3 520-9550 520-9550

P7/32" allen wrench 1 560-9715 560-9715

Q4mm allen wrench 1 560-9646 560-9646

R6mm allen wrench 1 N/A 560-9716

Sleft leg 1 009-0220 009-0220

Tright leg 1 009-0218 009-0218

Uwheel caster 2 600-0044 600-0044

Vwheel caster/brake 2 600-0045 600-0045

Wjoint connector nut 4 530-1037 530-1037

X3/8-16 x 1.5" screw bolt 4 520-1329 520-1329

YM10 x .402 ID lock washer 3 540-9424 540-9424

Zend cap 4 590-1032 590-1032

AA 1/4-20 x 20mm screw 2 520-2326 520-2326

BB 3/16 allen wrench 1 560-0071 560-0071

CC M4 x 12 mm serrated washer head socket pin screw 6 N/A 510-1079

DD M4 x 25 mm serrated washer head socket pin screw 4 N/A 510-1082

EE M5 x 12 mm socket pin screw 4 N/A 520-1064

FF M5 x 25 mm socket pin screw 4 N/A 520-1122

GG M6 x 12 mm socket pin screw 4 N/A 520-1050

HH M6 x 25 mm socket pin screw 4 N/A 520-1211

II M8 x 15 mm socket pin screw 6 N/A 520-1068

JJ M8 x 40 mm socket pin screw 4 N/A 520-1152

KK .219 ID x .5 OD x .5 HT spacer 4 N/A 540-1057

LL .344 ID x .75 OD x .5 HT spacer 4 N/A 540-1059

MM multi washer 6 N/A 580-1036

NN M6 x 20 mm socket pin screw 4 N/A 520-9554

OO M6 x 30 mm socket pin screw 4 N/A 520-1067

PP M8 x 25 mm socket pin screw 4 N/A 520-1101

QQ M10 x 15 mm socket pin screw 4 N/A 520-9262

Before you begin, make sure all parts shown are included with your product.

Parts may appear slightly different than illustrated.

4 of 14 ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07

Some parts may appear slightly different than illustrated.

CC DD

XFF

5 of 14 ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07

1Insert four end caps (Z) into ends of left and right support legs (T & S)as shown.

Guide left leg (S) towards base housing (E) as seen in fig.2.1. Then line up holes in base housing with holes in left leg. Fasten base housing

to left leg using two 3/8-16 x 1.5" screw bolts (X) and two joint connectors (W), tighten using 3/16"allen wrench (BB) and 7/32"allen

wrench (P) as shown in fig.2.2. Repeat for right side with right leg (T).

fig 2.2

fig 2.1

6 of 14 ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07

3Insert and screw casters (V & U) into holes of support legs (S & T). Attach casters with brake (V)to the back of left and right support legs

(S & T). Attach casters without brake (V)to front of support legs (S & T) as shown.

NOTE: Lock brakes on casters, for no sudden movements during installation.

HANDTHREAD

HOLDWHEEL

Attach upright (H) to base (E), as shown in in fig 4.2 using three 3/8-16 x 2.5" socket screws (O) and M10 x .402ID

lock washers (Y). Tighten screws using 7/32" allen wrench (P) shown in fig. 4.1.

fig 4.1

fig 4.2

CHORDMANAGEMENT

HOLES

7 of 14 ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07

SLOT

fig 6

Loosely attach four 1/4-20 x 12 mm screws (L), washers (N), and 1/4-20 nuts (M) to shelf support (C).

Slide shelf support (C)onto upright (H) so that 1/4-20 nuts (M) slide into slots of upright (H) as shown in figure

6 and detail 1. Slide shelf support to desired position, level, then tighten 1/4-20 x 12 mm screws (L) using 4

mmallenwrench(Q).

NOTE: MAXIMUMOFTWOSHELVES

Max height of top shelf is 34" from base.

Max height of second shelf is 28" from base.

DETAIL 1

8 of 14 ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07

Insert three button bumpers (K) into bottom of shelf clamp bracket (D).

Attach shelf clamp bracket (D) to shelf support (C) using two 1/4-20 x 20 mm screws (AA) and two

1/4-20nuts (M).

For additional shelf installation, repeat steps 5 through 7.

Insert six button bumpers (K) into shelf support (C). Place glass shelf (I) on shelf support.

7-1

7-2

AttachingGlassShelf

• Do not overtighten, may cause glass to shatter or

crack.

WARNING

9 of 14 ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07

Insert two 1/4-20 x 12 mm screws (L) into screen

mountbracket(A),leaving 3/16" of exposed thread

as shown in figure 11 and detail 3.

Snaptop cover (J) onto upright (H). 11

3/16"

fig 11

DETAIL 3

Loosely attach six 1/4-20 x 12 mm screws (L),

washers (N), and 1/4-20 nuts (M) to screen mount

bracket(A).

8Slide screen mount bracket (A) onto upright (H) so

that 1/4-20 nuts (M) slide into slots of upright (H) as

shown in figure 9 and detail 2. Slide screen mount

bracket to desired position, level, then tighten 1/4-20

x 12 mm screws (L) using 4 mm allen wrench (Q).

LNA

SLOT

fig 9

DETAIL 2

10 of 14 ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07

Attach universal plate (F) to hook plate (B) using four

M10 x 15 mm socket screws (QQ). Tighten screws

using 6 mm allen wrench (R).

Attaching Screen Using Universal Plate withAdapter Brackets

For attaching screens with VESA 100 hole pattern, skip to page 13.

13 Attach hook plate (B) to screen mount bracket (A).

14 Insert two 1/4-20 x 12 mm screws (L) into holes indicated below for desired screen orientation. Tighten all screws

using 4 mm allen wrench (Q).

2° Backward Tilt 5° Forward TiltNo Tilt

Other manuals for SR1G

This manual suits for next models

Table of contents

Other PEERLESS Rack & Stand manuals

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 