PCE Instruments PCE-EM 29 User manual

ELECTROSMOG METER

INSTRUCTION MANUAL

AVGMAX

CONTENTS

Title Page

1. SAFETY INFORMATION .............................................................. 1

2. INTRODUCTION........................................................................... 2

2-1 Fundamentals................................................................................ 2

2-2 Application..................................................................................... 3

2-3 Features........................................................................................ 4

3. SPECIFICATIONS......................................................................... 5

3-1 General Specifications .................................................................. 5

3-2 Electrical Specifications................................................................. 6

4. OPERATION ................................................................................. 7

4-1 Front panel controls description.................................................... 7

4-2 LCD display description ................................................................ 9

4-3 Use E-field sensor........................................................................11

4-4 Explanatory notes ........................................................................11

4-5 Setting the meter......................................................................... 14

4-6 Making measurements................................................................ 18

4-7 Manual data memory storing individual measured values .......... 19

4-8 Setting current data and time...................................................... 21

5. MEASUREMENT PREPARATION.............................................. 21

5-1 Battery Loading........................................................................... 21

5-2 Battery Replacement................................................................... 21

1. SAFETY INFORMATION

CAUTION

•Before making a measurement, check if the low battery symbol

( +) is shown on the display as soon as the meter is switched on.

Change the battery if the symbol is displayed.

•In the case of prolonged storage, it is preferable to remove the battery

from the meter.

•Avoid shaking the meter, particularly in the measurement mode.

•The accuracy and function of the meter may be adversely affected by the

specified limits outside and improper handling.

DANGER !

•In some cases, work in the vicinity of powerful radiation sources can be

a risk of your life.

•Be aware that persons with electronic implants(e.g. cardiac pacemakers)

are subject to particular dangers in some cases.

•Observe the local safety regulations of the facility operation.

•Observe the operating instructions for equipment which is used to

generate, conduct or consumer electromagnetic energy.

•Be aware that secondary radiators (e.g. reflective objects such as a

metallic fence) can cause a local amplification of the field.

•Be aware that the field strength in the near vicinity of radiators increases

proportionally to the inverse cube of the distance. This means that

enormous field strengths can result in the immediate vicinity of small

radiation sources (e.g. leak in waveguides, inductive ovens).

•Field strength measuring device can underrate pulsed signals.

Particularly with radar signals, significant measurement errors can arise.

•All field strength measuring devices have a limited specified frequency

range. Fields with spectral components outside of this frequency range

are generally incorrectly evaluated and tend to be underrated. Before

using field strength measuring devices, you should thus be certain that all

field components to be measured lie in the specified frequency range of

the measuring device.

2. INTRODUCTION

2-1 Fundamentals

Electromagnetic pollution :

This Meter used to indicate electromagnetic pollution generated

artificially. Wherever there is a voltage or a current, the electric (E)

and magnetic (H) fields arise. All types of radio broadcasting and TV

transmitters produce electromagnetic fields, and they also arise in

industry, business and the home, where they affect us even if our

sense organs perceive nothing.

Electric field strength (E) :

A field vector quantity that represents the force (F) on an infinitesimal

unit positive test charge (q) at a point divided by that charge. Electric

field strength is expressed in units of volts per meter (V/m).

Use the units of electric field strength for measurements in the following

situations:

•In the near-field area of the source.

•Where the nature of the electromagnetic field is unknown.

Magnetic field strength (H) :

A field vector that is equal to the magnetic flux density divided by the

permeability of the medium. Magnetic field strength is expressed in

units of amperes per meter (A/m).

The meter uses of magnetic field strength for measurements only in

the far-field area of the source.

Power density (S) :

Power per unit area normal to the direction of propagation, usually

expressed in units of watts per square meter (W/m2) or, for convenience,

units such as milliwatts per square centimeter (mW/cm2).

The characteristic of electromagnetic fields :

Electromagnetic fields propagate as waves and travel at the speed of

light (c). The wavelength is proportional to the frequency.

λ(wavelength) = c (speed of light)

f (frequency)

If the distance to the field source is less than three wavelength, then

we are usually in the near-field. If the distance is more than three

wave length, the far-field conditions usually hold.

In the near-field, the ratio of electric field strength (E) and magnetic

field strength (H) is not constant, so we have to measure each

separately.

In the far-field, however, it is enough to just measure one field quantity,

then the other could be computed accordingly.

2-2 Application

Quite often routine operation, maintenance and service work has to be

done in areas where active electromagnetic fields are present, e.g. in

broadcasting stations, etc. Additionally, other employees may be

exposed to electromagnetic radiation. In such cases, it is essential that

personnel are not exposed to dangerous levels of electromagnetic

radiation, such as:

High frequency (RF) electromagnetic wave field strength

measurement.

Mobil phone base station antenna radiation power density

measurement.

Wireless communication applications (CW, TDMA, GSM, DECT).

RF power measurement for transmitters.

Wireless LAN (Wi-Fi) detection, installation.

Spy camera, wireless bug finder.

Cellular/Cordless phone radiation safety level.

Microwave oven leakage detection.

Personal living environment EMF safety.

2-3 Features

The meter is a broadband device for monitoring high-frequency radiation

in the range from 10MHz to 8GHz. The non-directional electric field and

high sensitivity also allow measurements of electric field strength in TEM

cells and absorber rooms.

The unit of measurement and the measurement types have been

selected to expressed in units of electrical and magnetic field strength

and power density.

At high frequencies, the power density is of particular significance.

It provides a measure of the power absorbed by a person exposed to the

field. This power level must be kept as low as possible at high

frequencies.

The meter can be set to display the instantaneous value, the maximum

value measured or the average value. Instantaneous and maximum

value measurements are useful for orientation, e.g. when first entering an

exposed area.

10MHz to 8GHz Frequency range.

For isotropic measurements of electromagnetic fields.

Non-directional (isotropic) measurement with three-channel

measurement sensor.

High dynamic range due to three-channel digital results processing.

Configurable alarm threshold and memory function.

Easy & safety to use.

3. SPECIFICATIONS

3-1 General Specifications

•Measurement method : Digital, triaxial measurement.

•Directional characteristic : Isotropic, triaxial.

•Measurement range selection : One continuous range.

•Display resolution : 0.1mV/m, 0.1µA/m, 0.1µW/m2, 0.001µW/cm2

•Setting time : Typically 1s (0 to 90% of measurement value).

•Display refresh rate : Typically 0.5 seconds

•Display type : Liquid-crystal (LCD), 4 digit.

•Audible alarm : Buzzer.

•Units : mV/m, V/m, µA/m, mA/m, µW/m2, mW/m2, W/m2, µW/cm2,

mW/cm2

•Display value : Instantaneous measured value, maximum value,

average value, or maximum average value.

•Alarm function : Adjustable threshold with ON/OFF.

•Calibration factor CAL : Adjustable.

•Manual data memory and read storage : 99 data sets.

•Dry batteries : 9V NEDA 1604/1604A (Alkaline battery)

•Battery life : > 3 hours

•Auto power off : 5 minutes.

•Operating temperature range : 0℃to +50℃

•Operating humidity range : 25% to 75%RH

•Storage temperature range : -10℃to +60℃

•Storage humidity range : 0% to 80%RH

•Dimensions : Approx. 67(W)×60(T)×247(L)mm.

•Weight (including battery) : Approx. 250g

•Accessories : Instruction manual, battery, Carrying case.

3-2 Electrical Specifications

Unless otherwise stated, the following specifications hold under

the following conditions :

•The meter is located in the far-field of a source, the sensor head is

pointed towards the source.

•Ambient temperature : +23℃±3℃

•Relative air humidity : 25% to 75%

Sensor type : Electrical field (E)

Frequency range : 10MHz to 8GHz

Specified measurement range :

•CW signal (f > 50MHz) : 20mV/m to 108.0V/m ,

53µA/m to 286.4mA/m ,

1µW/m2to 30.93W/m2,

0µW/cm2to 3.093mW/cm2

Dynamic range : Typically 75dB

Absolute error at 1 V/m and 50 MHz : ±1.0dB

Frequency response :

•Sensor taking into account the typical CAL factor :

±1.0dB (50MHz to 1.9GHz)

±2.4dB (1.9GHz to 8GHz)

•Isotropy deviation : Typically ±1.0dB (f>50MHz)

•Overload limit : 10.61mW/cm2(200V/m)

•Thermal response (0 to 50℃): ±0.5dB

4. OPERATION

4-1 Front panel controls description

AVGMAX

(1). E-field sensor.

(2). LCD display.

(3). key : Press this key to turn the meter on or off.

(4). key : Press this key to change sequential : “Instantaneous”→

“Max. instantaneous” →“Average” →“Max. average”.

(5). key :

cPress this key to change units selector : “mV/m or V/m” →“µA/m or

mA/m” →“µW/m2, mW/m2or W/m2”→“µW/cm2or mW/cm2”

dPress and hold this key while turning the meter on to disable the

audible sound, the “ ” symbol will disappear.

(6). key :

cPress this key to switch to display date and time.

dPress and hold this key while turning the meter on to the alarm

setting mode, press key two times to exit this mode.

3Press this key for 3 seconds to switch the alarm function on or off.

(7). key : Press this key to enter the current data and time setting

mode, press this key again to exit this mode.

(8). key :

cPress this key to change sensor axis selector : “All axis” →“X axis”

→“Y axis” →“Z axis”.

dPress and hold this key while turning the meter on to switch the

device to the calibration factor setting mode, press “SET” key to exit

this mode.

(9). key :

cPress this key one time to store one data set to memory.

dPress and hold this key while turning the meter on to enter the clear

manually recorded data mode, press key to exit this mode.

(10). key :

cPress this key to switch to the manual data reading mode, press this

key again to exit this mode.

dPress and hold this key while turning the meter on to disable the auto

power off function, the “ ” symbol will disappear.

(11). STWX key : Setting current date and time, datalogging interval time,

alarm setting value, calibration factor setting value, or recall manual

data memory to read memory data in cycles control keys.

Table of contents

Other PCE Instruments Measuring Instrument manuals

PCE Instruments

PCE Instruments PCE-PH 23 User manual

PCE Instruments

PCE Instruments PA6000 User manual

PCE Instruments

PCE Instruments PCE-DFG NF Series User manual

PCE Instruments

PCE Instruments PCE-DT 50 User manual

PCE Instruments

PCE Instruments 880 User manual

PCE Instruments

PCE Instruments PCE-353N User manual

PCE Instruments

PCE Instruments PCE-EM 890 User manual

PCE Instruments

PCE Instruments PCE-VT 3800 User manual

PCE Instruments

PCE Instruments PCE-MSR 150 User manual

PCE Instruments

PCE Instruments PCE-322-SC43 User manual

PCE Instruments

PCE Instruments PCE-TG 300-NO2-ICA User manual

PCE Instruments

PCE Instruments PCE-PTR 200N User manual

PCE Instruments

PCE Instruments PCE-OO User manual

PCE Instruments

PCE Instruments PCE-DMM 70 User manual

PCE Instruments

PCE Instruments PCE-125 Series User manual

PCE Instruments

PCE Instruments PCE-PH 25 User manual

PCE Instruments

PCE Instruments DFG N Series User manual

PCE Instruments

PCE Instruments PCE-MSM 4 User manual

PCE Instruments

PCE Instruments PCE-830+PCE-6801 User manual

PCE Instruments

PCE Instruments PCE-VE 1000 User manual

PCE Instruments

PCE Instruments PCE-555BT User manual

PCE Instruments

PCE Instruments PCE-CT 5000 User manual

PCE Instruments

PCE Instruments PCE-DD Series User manual

PCE Instruments

PCE Instruments PCE-007 User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual