Panasonic BL-WV10A User manual
ORDER NO. KMS0505067CE
F5
Wireless Camera Monitoring System
BL-WV10A
(for U.S.A.)
2005 Panasonic Communications Co., Ltd. All rights reserved.
Unauthorized copying and distribution is a violation of law.
IMPORTANT INFORMATION ABOUT LEAD FREE, (PbF), SOLDERING
If lead free solder was used in the manufacture of this product the printed circuit boards will be marked
PbF.
Standard leaded, (Pb), solder can be used as usual on boards without the PbF mark.
When this mark does appear please read and follow the special instructions described in this manual
on the use of PbF and how it might be permissible to use Pb solder during service and repair work.
1. ABOUT LEAD FREE SOLDER (PbF: Pb free)
Note:
In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard
solder or solder that contains lead.
1
We will use PbF solder when discussing the lead free solder used in our manufacturing process which
is made from Tin, (Sn), Silver, (Ag), and Copper, (Cu).
This model, and others like it, manufactured using lead free solder will have PbF stamped on the PCB.
For service and repair work we suggest using the same type of solder although, with some precautions,
standard Pb solder can also be used.
Caution
- PbF solder has a melting point that is 50° ~ 70° F, (30° ~ 40°C) higher
than Pb solder. Please use a soldering iron with temperature control
and adjust it to 700° ± 20° F, (370° ± 10°C). In case of using high
temperature soldering iron, please be careful not to heat too long.
- PbF solder will tend to splash if it is heated much higher than its melting
point, approximately 1100°F, (600°C).
- If you must use Pb solder on a PCB manufactured using PbF solder,
remove as much of the original PbF solder as possible and be sure that
any remaining is melted prior to applying the Pb solder.
- When applying PbF solder to double layered boards, please check the
component side for excess which may flow onto the opposite side (See
figure, below).
1.1. SUGGESTED PbF SOLDER
There are several types of PbF solder available commercially. While this product is manufactured using
Tin, Silver, and Copper, (Sn+Ag+Cu), you can also use Tin and Copper, (Sn+Cu), or Tin, Zinc, and
Bismuth, (Sn+Zn+Bi). Please check the manufacturer’s specific instructions for the melting points of
their products and any precautions for using their product with other materials. The following lead free
(PbF) solder wire gauge are recommended for service of this product: 0.3mm, 0.6mm and 1.0mm.
1.2. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS USED
2
COMPONENT VIEW
BOTTOM VIEW
3
2. FOR SERVICE TECHNICIANS
ICs and LSIs are vulnerable to static electricity.
When replacing, the following precautions will help to prevent recurring malfunctions.
1. Cover the plastic parts with aluminum foil.
2. Ground the soldering irons.
3. Use a conductive mat on the work-table.
4
4. Do not grasp IC or LSI pins with bare fingers.
3. CAUTION
3.1. SAFETY PRECAUTIONS
1. Before servicing, unplug the power cord to prevent an electrical shock.
2. When replacing parts, use only manufacturer’s recommended
components for safety.
3. Check the condition of power cord. Replace if wear or damage is
evident.
4. After servicing, be sure to restore the lead dress, insulation barriers,
insulation papers, shields, etc.
5. Before returning the serviced equipment to the customer, make the
following insulation resistance test to prevent a shock hazard.
3.2. CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries accoding to the manufacturer’s Instructions.
3.3. TRADEMARKS
- Adobe, Acrobat and Reader are either registered trademarks or
trademarks of Adobe Systems Incorporated in the United States and/or
other countries.
- Ethernet is either a registered trademark or a trademark of Xerox
Corporation in the United States and/or other countries.
- Microsoft, Windows and ActiveX are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other
countries.
- Pentium is a trademark or registered trademark of Intel Corporation or
its subsidiaries in the United States and other countries.
- SD mark is a trademark of the SD Card Association.
- Screen shots reprinted with permission from Microsoft Corporation.
- All other trademarks identified herein are the property of their respective
owners.
5
3.4. INSULATION RESISTANCE TEST
1. Unplug the AC power cord and short the two prongs of the plug with a
jumper wire.
2. Measure the resistance value with ohmmeter between the jumpered AC
plug and each exposed metal cabinet part, such as screw threads, etc.
Note:
Some exposed parts may be isolated from the chassis by design. These will read infinity.
3. If the measurement is outside the specified limits, there is a possibility
of shock hazard. The equipment should be repaired and rechecked
before it is returned to the customer.
3.5. POWER CAUTION
The power socket wall outlet should be located near this equipment and be easily accessible.
4. SPECIFICATIONS
Main Unit:
LAN Interface
6
Items Specifications
Number of ports 4 port
Connector type 8-pin modular jack (RJ-45)
Physical interface IEEE802.3 (10BASE-T)
IEEE802.3u (100BASE-TX)
MDI/MDI-X with auto-detect
Wireless Interface
Items Specifications
IEEE802.11g
Transmission protocol OFDM (IEEE802.11g standard)/DS-SS
(IEEE802.11b compatible), half duplex
Transmission speed
([standard value] Mbps)
54/48/36/24/18/12/9/6 *(IEEE802.11g standard):
automatic fallback
Frequency range (MHz) 2412 to 2462 (center frequencies)
Number of channels 11
IEEE802.11b
Transmission protocol DS-SS, half duplex
Transmission speed
([standard value] Mbps)
11/5.5/2/1 *(IEEE802.11b standard): (automatic fallback)
Frequency range (MHz) 2412 to 2462 (center frequencies)
Number of channels 11
Communication range The range will depend on environmental conditions.
The proximity of reinforced concrete structures, large metal objects,
microwave ranges, and/or theft prevention devices can shorten the range.
Obstructions (walls, furniture, equipment) can also shorten the usable range.
- The values displayed represent the theoretical maximums for wireless
LAN standards, and do not represent actual data transmission speeds.
Video Output
Items Specifications
Video format NTSC
Output jack Single jack
Output level 1.0 Vp-p (75 )
User Interface
7
Items Specifications
FACTORY DEFAULT
RESET button
Restoration of default settings
Mode switch Normal, Setup, Sequential Display
ALERT Camera sensor notification
Indicator displays Power (green/orange/red), Sensor (orange), ALERT (green), SD Memory Card
(green/orange),
Wireless (green), LAN 1 through LAN 4 (green)
Recording media SD Memory Card
Other
Items Specifications
AC adapter AC110 V (60Hz) DC12 V (part number PQLV202Y)
DC cord length: About 3.0 m (10 ft.)
AC cord length: About 1.8 m (separate)
Power consumption: 7.5 W
Antenna Diversity antenna
Exterior dimensions W x H x D: About 220 mm x 42 mm x 171 mm (8.6 in. x 1.6 in. x 6.7 in.) with
antenna collapsed and no stand
Weight (Main Unit Only) About 500 g (1.1 lb)
Operational environment 0°C~40 °C (32°F~104 °F) humidity between 20 and 85% (without condensation)
EM radiation shielding FCC Part 15
Software:
Camera Viewer
Items Specifications
Camera image display Displays a maximum of eight camera images
Video (motion JPEG): 640x480, 320x240
1 screen per 8 pages, 4 screens per 2 pages
Camera pan/tilt operations, image size switching, resolution switching
Recording to and playing
from SD memory cards
Movies (motion JPEG): 640 x 480, 320 x 240
Saved in QuickTime format
Pictures (JPEG): 640 x 480, 320 x 240
Timer recording
Camera motion sensor
support
Automatic switch to camera image at sensor input event sensor input
triggers buzzer/LED notification
Automated camera image recording at sensor input event
Setup
Items Specifications
Quick Setup Automatically performs necessary network and wireless settings for
Panasonic cameras and routers
8
Wireless Terminal Feature
Items Specifications
Security WEP (64 bit/128 bit/152 bit), wireless stealth functionality (SSID suppression,
connection denial/permissions through ANY key), MAC address filtering
Notice Regarding Wireless Communications
1. To avoid wireless communication interference and instability, do not
use this product near the following devices, or change the wireless
channel used by the BL-WV10A.
- Wireless transmitters (radio transmitters, cellular transmitters, etc.)
- Wireless devices which operate at 2.4 GHz (security equipment,
POS systems, cordless telephones, etc.)
- Microwave ovens
2. Wireless commnication range and quality may be affected if the
following types of objects are located between or near this product and
other wireless devices connected to this product. In the event that
images do not refresh at a regular rate, become cut off, etc., relocate
this product, the other wireless devices, or the obstacles (if possible)
for more stable wireless communications.
- Metal door shutters
- Walls made of concrete,stone,or brick,or walls which contain
aluminiumbased heat insulation
- Multiple walls
- Fire doors and glass
- Steel racks or shelves
3. Place cameras and this product at least 2 m (6.5 ft.)away from
radios.Do not connect cameras and this product to a power outlet used
by a radio.
Frame rate
- Frame rate (frames per second,‘‘fps’’)may vary depending on the image
being viewed by the camera, brightness, and other environment
conditions, as well as network conditions such as distance between the
BL-WV10A and the cameras, the number of cameras connected,
network traffic, wireless network conditions, etc.
9
- For BL-C10A and BL-C30A, a maximum of 15 fps in LOW quality
(resolution) and 7.5 fps in HIGH quality is possible.
- For HCM series cameras, a maximum of 30 fps in LOW quality and 12
fps in HIGH quality is possible.
- Network speed may decrease while the BL-WV10A is turned on and
connected to cameras.
- The display size and brightness of the Monitoring Screen can be
adjusted.
5. PARTS LOCATIONS
5.1. MAIN UNIT
Front Panel
1. SD Memory Card port
2. Timer/Busy indicator
3. Power indicator
4. Alert indicator
5. Sensor indicator
6. LAN indicators
7. Wireless indicator
8. Remote control sensor
Rear Panel
10
Other manuals for BL-WV10A
3
Table of contents
Other Panasonic Measuring Instrument manuals
Panasonic
Panasonic KC2S Eco-COUNT METER User manual
Panasonic
Panasonic NV-8950 User manual
Panasonic
Panasonic NA1-11 User manual
Panasonic
Panasonic KW2M User manual
Panasonic
Panasonic DMR-HW220 User manual
Panasonic
Panasonic AJ-PG50EJ User manual
Panasonic
Panasonic KW8M User manual
Panasonic
Panasonic LH2H-FE-DHK User manual
Panasonic
Panasonic TH13 Series User manual
Panasonic
Panasonic LC2H preset User manual
Panasonic
Panasonic FZ-VNP001U User manual
Panasonic
Panasonic KW1M Eco-Power METER User manual
Panasonic
Panasonic KW2G Eco-POWER METER User manual
Panasonic
Panasonic RRQR100 - IC RECORDER User manual
Panasonic
Panasonic LP-V10U-C User manual
Panasonic
Panasonic AG-RT850P User manual
Panasonic
Panasonic FM-252-4(-P) User manual
Panasonic
Panasonic KW2G Eco-POWER METER User manual
Panasonic
Panasonic WJ-NX100/2E User manual
Panasonic
Panasonic DMR-UBT1GL-K User manual
