Panasonic EYFLA7AR Operating instructions

Two-Way Quick Programming Guide

Two-Way communicationcapable Tool Models:

EYFLA7AR, EYFLA8PR/CR/AR, EYFLA9PR/CR,EYFMA2PR/CR, EYFNA1PRT/CRT/,JRT,& EYFPA1JRT

(Pleaserefer to the Owner's Manualfor further instruction beyond this Quick Guide)

These models can operate in both One-Way mode or Two-Way mode.

•One-Way communication mode –The Remote controlis used to change tool settings.

•Two-Way communication mode –The Qualifier will changetool features and will override any settings made by the remote control.

Programming the tool with the remote control

1. Cycle Power –Remove then re-installthe batteryon the tool.

2. Enter Program Mode –On the tool,

•press and hold down the “Light Button” while pulling and releasing the tool’s “Trigger/Switch” youcan then release both

buttons.

•The display starts blinking, the tool is now in programmode.

•If the display is solid, returnto step one.

3. Edit ProgrammableFeatures–While the displayis flashing, use the remotecontrolto changefeature settingsaccordingto the charton

page 2.

Each press of the A,B,C or D buttons on the remote control will cycle through the sub-menus.

The + and –buttons change the sub menu feature values

The blue button is the Save button. Press this button after features are selected to save changes.

Two-Way Quick Programming Guide

How to set Programmable Features

Button Number

ofPush Setting Mode Tool display Description

0 Torquesetting 1~40: Shut-off

F: Non shut-off Select stage with ＋/－button. Initial setting is 「F」.

1 time Flush(Snugtorque)detectionmode

setting L1: Stage1

～L7: Stage7

Select stage with ＋/－button. Initial setting is 「L1」.

L1: For applications with light load bef ore snug point

～L7: For applications with heavy loads or v arying joint rate before snug point

2 times Buzzer setting b0: No buzzer

b1: Buzzer withOK

b2: Buzzer w ithNOK Select stage with ＋/－button. Initial setting is 「b0」.

3 times Flush(Snugtorque)detectiondelay J0: OFF

01～30: 0.1～3.0sec.

Select stage with ＋/－button. Initial setting is 「J0」.

The tool doesn’t activ ate Snug Torque Detection mode and ignores load during rundown for

a selected time period.

1 time LED light d1: by LED button (for 5min)

d2: by trigger switch Select stage with ＋/－button. Initial setting is 「d1」.

2 times Rundownerrordetecting 0～30: 0～3.0sec. Select stage with ＋/－button. Initial setting is 「0」.

If the clutch is activ ated before the programmable minimum runtime,

the tool alerts the operator to a NOK fastening. (0.1sec. per stage)

3 times Variablespeedcontrol P0: Variablespeed (ON)

P1: Single speed(OFF) Select stage with ＋/－button. Initial setting is 「P0」.

Speed can be controlled by use of thetrigger.

1 time Resetsettings FAll settings return to initial setting.

2 times Maintenanceinterval alarm 0～99: 0-99Rundowns Select stage with ＋/－button. Initial setting is 「0」

When total f astening times are within 1 hour of preset maintenance interv al, tool’s display

blinks notifying the operator.

Once tool reaches the preset interval, the tool is looked out from further use.

3 times Out of rangedisablefunction C0: OFF

C1: ON

Select stage with ＋/－button. Initial setting is 「C0」

In the event that wireless communication cannot be completed between the tool and the

qualifier, the tool will be disabled and cannot be operated.

4 times CommunicationMode 90: 1-way

91: 2-way

Only available on models equipped with 2-way communication

Toggle communication mode between 1-way & 2-

way

R1: 360°reverce(ON)

Select stage with ＋/－button. Initial setting is 「R0」

Tool first reverses 360degree, aligning the threads, greatly reducing the possibility of cross

threads.

2 times Retighteningprevention U-U9: 0～3.0sec. Select stage with ＋/－button. Initial setting is 「U」

Tool prevented from operating during a selected time period after shut-of f.

3 times Socket extension mode h0: Normal

h1: for 150mm socket

h2: for 250mm socket

Select stage with ＋/－button. Initial setting is 「h0」

RPM during impacts is adjusted depending on socket extensionlength tostabilize torque.

Note: The Default setting for the models listed on page 1 is One-Way communication mode.

Important: The communicationmode must be changed with the remote before learning the tool to

the qualifier to initiate Two-Way communication. (See below instructions)

Two-Way Quick Programming Guide

To change the tool communication mode from the default “90” (one way) to “91” (two-way)

1. Put the tool into program mode

2. Press “C” button on the remote 4 times

3. Press the + button on the remote to select “91” (two-way)

4. Press the Blue set button to save the changes

Sleep Mode

•If the tool is in “sleep mode” (timed out from no operation and no display) Default is 20 min. the tool will not communicate

•Tool sleep time can be changed in the qualifier settings under Qualifier setting page 2 (select next) then select “Tool on time”. Sleep

time range is 20 -720 min.

•Pulling the tool trigger will “wake” the tool and initiate communication.

In the event the qualifier is powered down or loses power while the tool is in sleep mode, you must power up the

qualifier firstbefore waking the tool from sleep to initiate two-way communication. Otherwise you will need to pull

and reinstallthe battery on the tool

Two-Way Quick Programming Guide

Learning tools to the Qualifier

1. Power up the qualifier. Press the button below, ‘Menu’.

2. Enter the password 1011 (default) using the numeric

keypad and press ENT when completed.

3. In the menu, right arrow to “Tools” and press ENT.

4. Press the button below, “Learn” to begin the learn process

5. Follow the directions on screen to learn the tool.

6. The unit will return to the Tools screen with the learned tool,

named “Tool 1” instead of “No Tool”.

7. You can now repeatthe learning process for the next tool or

8. return to the menu by pressing ESC or the button below Exit.

1. 3.

4. 5.

Learning tools to the Qualifier continued

To the right, is an example of 2 tools learned to the Qualifier.

•One tool is in One-Way mode “90”

•The other tool is in Two-Way mode “91”

Note the difference in illustration1

•Tool 1 is in Two-Way and displays the (Model number)

•Tool 2 is in One-Way mode and displays(OK/NOK)

Switching from One-Way mode to Two-Way mode

If you learn a tool in One-Way mode “90” and want to relearn it

to Two-way mode “91”, you must “forget” the tool first.

1. Change the “Communication Mode’ in the tool from “90 to

“91”with the remote (page 3).

2. Go to the Tool tab, “edit’ then “Forget”.

3. Then learn the tool to the qualifier (page 4)

Two-Way Quick Programming Guide

Parameters/Features

1. Name the Parameter

2. Socket Tray

3. Set the Batch count

4. Select lock on batch if required

5. Torque Settings: 1-40. Default–1

6. Flush Detection: 1-7. Default –1

7. Buzzer settings: Off, OK, NOK. Default - Off

8. Flush Detect Delay: .1 –3 sec. Default–0

9. LED light: Trigger switchor LED button. Default –LED Button

10. Cross thread/Rehit: 0-3 sec. Default –0

11. Variable speed: Variable Speed or Single. Default –Variable

12. Cross Thread reduction: 540˚ reverse or OFF. Default – OFF

13. Retightening Prevention: 0-3sec. Default- 0

14. Socket ext. mode: 150mm. 250mm, None. Default - None

Two-Way Quick Programming Guide

Editing the Parameters for each tool

•Tools can only be learned to Parameters 1-16.

•Parameters 17-100 areassignableto any of the tools 1-16.

1. Go to “Parameters”, from the main menu.

2. Select the parameter location you want then press “edit”

*Two-Way communication mode –The Qualifier will change tool features and will override any settings made by the remote control.

(Assembly Manager softwareis available on our Website and can also be used

to make parameter changes, createjobs, groups, etc.)

Programingmultiple Parameters to a single tool

1. Go to parameters tab (page 4)

2. Select 17 and above parameters

3. Go down to “tools:” to assign the tool.

4. Enter the number on the keypad

5. Select “Save”

6. Repeat to 18 and so on.

Creating a Job for a sequence of events

1. Go to the Jobs tab

2. Select the Job you want

3. Select “edit”

4. Select “Steps”

5. Assign the parameters or groups as shown to the right

6. Exit and “save”

Two-Way Quick Programming Guide

Tools in two-way mode that are in a job sequence will flash orange on the

rear LED panel when that tools parameter is active so the operatorknows

which tool to use.

This manual suits for next models

Other Panasonic Controllers manuals

Panasonic

Panasonic FP-M Hardware User manual

Panasonic

Panasonic FP-XH Series User manual

Panasonic

Panasonic HG-SC User manual

Panasonic

Panasonic FP7 Series User manual

Panasonic

Panasonic WVCU161C - SYSTEM CONTROLLER User manual

Panasonic

Panasonic FP7 Series User manual

Panasonic

Panasonic AK-HRP1015 Use and care manual

Panasonic

Panasonic CZ-256ESMC2 User manual

Panasonic

Panasonic FP7 Series User manual

Panasonic

Panasonic AFP7X16DW User manual

Panasonic

Panasonic FP Series Owner's manual

Panasonic

Panasonic GM1 Series User manual

Panasonic

Panasonic MINAS-A4P Use and care manual

Panasonic

Panasonic Vossloh-Schwabe Light Controller IP/DALI 2CH User manual

Panasonic

Panasonic FP7 Series User manual

Panasonic

Panasonic FP3 User manual

Panasonic

Panasonic FP0H Series User manual

Panasonic

Panasonic WV-ASM100 User manual

Panasonic

Panasonic DPC-100 Series User manual

Panasonic

Panasonic AG-A850 User manual

Panasonic

Panasonic CZ-64ESMC3 User manual

Panasonic

Panasonic S-Link FP2 User manual

Panasonic

Panasonic FP2 ET-LAN User manual

Panasonic

Panasonic CZ-TACG1 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide

KUHN

KUHN TKS user manual