Panasonic WV-ASM100 User manual
- 1 -
System Controller WV-CU950 Setup Tool
PC Software Package
Operating Instructions
Model No. WV-ASM100
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
Preface
This software is installed on a PC to configure the settings of System Controller WV-CU950 relating to network.
Installation
1. Insert the supplied CD-ROM into the CD-ROM drive on the PC.
2. Double-click "CU950EtherToolInst.exe" in the "Tool" folder of CD-ROM.
The installation wizard will be displayed on the PC screen.
3. Click "Next", and follow the directions.
Notes:
• It is required that Windows Installer 3.1 is installed on the PC to use this software.
• In the factory default installation, "C:\Program Files\Panasonic\WV-CU950 Setup Tool" is created, and files will be copied to
the directory.
Uninstallation
1. Select "Control Panel" - "Add/Remove Programs".
"Add/Remove Programs" window will be displayed on the PC screen.
2. Select "WV-CU950 Setup Tool".
3. Click "Remove", and follow the directions.
Note: If System Controller WV-CU950 Setup Tool has already been installed on a PC, installation is impossible. Install the
application again after uninstallation.
- 2 -
Starting Up
This software communicates with System Controller WV-CU950 via the RS-232C interface when setting the IP address of system
controller or reading out the system controller setting.
1. Connect the system controller and PC with a 9-pin D-sub cross cable.
2. Select "Start" - "All Programs" - "Panasonic" - "WV-ASM100" - "WV-CU950 Setup Tool" or double-click the "WV-CU950
Setup Tool" icon on the desktop.
System Controller WV-CU950 Setup Tool will start up, and the "Serial port" window will be displayed on the PC screen.
Notes:
･When clicking "Version information", the "Setup Tool" window will appear to display the software version. When clicking
"OK", the screen returns to the "Serial port" window.
･When clicking "Help", the "Help" window will appear. When clicking "OK", the screen returns to the "Serial port" window.
3. Select the number for "Port", and click "OK". "IP address setting" window will be displayed.
4. Turn on the power while holding down the button 7 and MON (ESC) button of system controller.
"Admin Password" entry form will appear on the LCD of system controller.
5. Enter the administrator password. (The factory default is "650".) Then, press the SET button. Short buzzer will sound three
times, "GXCU-THRU-MODE" will appear on the LCD, and all the buttons in the "IP address setting" window will become
available.
Notes:
･When returning from "IP address setting" window to the "Serial port" window, click "Close".
･When such a communication error as cable disconnection happens, "Communication Error" window will appear.
･Refer to the operating instructions of system controller for details on the administrator password.
- 3 -
Configure the Settings Relating to Network
Configure and check the settings relating to network in the "IP address setting" window.
Note: When opening this window for the first time, the factory default will be displayed. To check the current settings of system
controller, click "Load".
[IP (WV-CU950)]
Enter the IP address of system controller
as "nnn.nnn.nnn.nnn".
Available value for "nnn": 0 to 255
Default: 192.168.0.210
[Subnet mask]
Enter the subnet mask of system controller
as "nnn.nnn.nnn.nnn".
Available value for "nnn": 0 to 255
Default: 255.255.255.0
[Gateway]
Enter the gateway IP address of system controller as "nnn.nnn.nnn.nnn".
Available value for "nnn": 0 to 255
Default: 192.168.0.1
[IP (WV-ASM100)]
Enter the IP address of PC in which WV-ASM100 is installed.
Available value for "nnn": 0 to 255
Default: 192.168.0.200
[Keyboard ID]
Surely set the number to 01.
[Set] button
Saves the settings in the system controller.
[Load] button
Reads out the settings from the system controller.
When finishing the setup
Restart the system controller in the normal operation mode.
1. Click "Restart" in the "IP address setting" window.
"Connecting to Main CPU…" will appear on the LCD of system controller.
2. Click "Close". "IP address setting" window will disappear, and the screen returns to the "Serial port" window.
3. Click "Exit". You will exit the software.
Notes:
･When a message other than "Connecting to Main CPU…" after the restart, check that the settings of MODE switches and
CONTROLLER NO. switch at the rear panel are as follows.
If the settings differ from the illustrations, turn off the system controller, set the switches, and turn on the system controller
again. Then, check that "Connecting to Main CPU…" appears on the LCD.
MODE
12345678
OFF
ON
CONTROLLER
NO.
0
9
8
7
6
5
4
3
2
1
･After all the settings, disconnect the 9-pin D-sub cross cable from the system controller and PC.
For U.S., Canadian and Puerto Rican fields:
Panasonic System Solutions Company,
Unit Company of Panasonic Corporation of North America
Security Systems
http://www.panasonic.com/security
For customer support, call 1.877.733.3689
Executive Office: Three Panasonic Way 2H-2, Secaucus, New Jersey 07094
Zone Office
Eastern: Three Panasonic Way, Secaucus, New Jersey 07094
Central: 1707 N. Randal Road, Elgin, IL 60123
Southern: 1225 Northbrook Parkway, Suwanee, GA 30024
Western: 6550 Katella Ave., Cypress, CA 90630
Panasonic Canada Inc.
5770 Ambler Drive,Mississauga,
Ontario, L4W 2T3 Canada (905)624-5010
http://www.panasonic.ca
Panasonic Sales Company
Division of Panasonic Puerto Rico Inc.
San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina
P.R. 00985(809)750-4300
For European and other fields:
Matsushita Electric Industrial Co., Ltd.
Osaka, Japan
http://panasonic.net
© 2007 Matsushita Electric Industrial Co., Ltd. All Rights Reserved. N0207-1037 V8QB6641BN Printed in Japan
This manual suits for next models
1
Table of contents
Other Panasonic Controllers manuals
Panasonic
Panasonic FP-I4C User manual
Panasonic
Panasonic S-Link FP2 User manual
Panasonic
Panasonic MGSD Installation guide
Panasonic
Panasonic GM1 Series User manual
Panasonic
Panasonic PAW-PACR3 User manual
Panasonic
Panasonic FP7 Series User manual
Panasonic
Panasonic AW-RP60GJS User manual
Panasonic
Panasonic AWRP605P - MULTI FUNCTION CONTROLLER User manual
Panasonic
Panasonic Vossloh-Schwabe Light Controller IP/DALI 2CH User manual
Panasonic
Panasonic FP-X0 L14R User manual
Panasonic
Panasonic AG-A850 User manual
Panasonic
Panasonic SFC-HC User manual
Panasonic
Panasonic FP0R Series User manual
Panasonic
Panasonic FP7 Series User manual
Panasonic
Panasonic WV-CU980/G User manual
Panasonic
Panasonic EYFLA7AR Operating instructions
Panasonic
Panasonic CF-VEBC11U User manual
Panasonic
Panasonic FP7 Series User manual
Panasonic
Panasonic AKHRP900P - CAMERA CONTROLLER HC User manual
Panasonic
Panasonic CZ-ANC2 User manual
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
