Optika XZ-2 User manual
XZ-2
OPERATION MANUAL
GUIDA UTENTE
MANUAL DE INSTRUCCIONES
Page 2
INDEX
1.0 DESCRIPTION page 4
2.0 INTRODUCTION page 5
3.0 UNPACKING AND ASSEMBLY page 5
4.0 USING THE MICROSCOPE page 15
5.0 MAINTENANCE page 19
6.0 ELECTRICAL SPECIFICATIONS page 19
7.0 RECOVERY AND RECYCLING page 20
Page 3
This microscope is a scientic precision instrument designed to last for many years with a minimum of main-
tenance. It is built to high optical and mechanical standards and to withstand daily use.
Optika reminds you that this manual contains important information on safety and maintenance, and that it
must therefore be made accessible to the instrument users.
Optika declines any responsibility deriving from instrument uses that do not comply with this ma-nual.
Safety guidelines
This manual contains important information and warnings regarding safety about installation, use and mainte-
nance of the microscope. Please read this manual carefully before using the equipment. To ensure safe use,
the user must read and follow all instructions in this manual. OPTIKA products are designed for safe use in
normal operating conditions. The equipment and accessories described in the manual are manufactured and
tested according to industry standards for safety instrumentation laboratory. Misuse can cause personal injury
or damage to the instrument. Keep this manual at hand close to the instrument, for an easy consultation.
Electrical safety
Before connecting the power cord to wall outlet, ensure that your mains voltage for your region corresponds
to the voltage supply of the instrument, and that the illuminator’s switch is in position OFF. The user must
observe the safety regulations in force in his region. The instrument is equipped with CE safety marking, in
any case the user has full responsibility concerning the safe use of that instrument.
Warning/Caution symbols used in this manual
The user should be aware of safety aspects when using the instrument. Warning or hazard symbols are
shown below. These symbols are used in this manual.
The instructions on this symbol to avoid possible severe personal injuries.
Warning of use; the incorrect operation on the instrument can cause damages
to the person or instrument.
Possibility of electric shock.
Attention: high temperature surfaces. Avoid direct contact.
Technical notes or usage tips.
SAFETY GUIDELINES
Page 4
1.0 DESCRIPTION
EYEPIECES
DIGITAL CAMERA
LCD
ZOOM ADJUSTMENT
RING
LED BRIGHTNESS
CONTROL
DIOPTRIC
COMPENSATION
FOCUS / TENSION
KNOB
LED RING
ILLUMINATOR
Page 5
This microscope is a scientic precision instrument designed to last for many years with a minimum
of maintenance. It is built to high optical and mechanical standards and to withstand daily laboratory
use.
Optika reminds you that this manual contains important information on safety and maintenance, and
that it must therefore be made accessible to the instrument users.
Optika declines any responsibility deriving from instrument uses that do not comply with this ma-
nual.
3.0 UNPACKING AND ASSEMBLY
2.0 INTRODUCTION
Components of the microscope
Unpack the components of the microscope from the box and put them on a stable surface. In the
packaging you nd:
1 - PILLAR BASE
Connect the mains plug into the socket at the base
Make sure, before you turn the illumination on, that the voltage selector is set to the mains voltage for your
region.
The power cord should be used only on network sockets equipped with adequate grounding.
Contact a technician to check the state of your electrical system. If there is no need to install additional acces-
sories, the instrument is now ready for use. Once positioned and installed with the necessary components,
the microscope is ready to be used. Your microscope is a laboratory instrument designed to last. Handle it
always carefully and avoid abrupt vibrations or shocks. Always disconnect the power cable from the micro-
scope when not in use for long time, while you clean it or when you perform any maintenance.
AVOID DISASSEMBLING THE INSTRUMENT
Do not disassemble the instrument. This entails the cancellation of the warranty and may cause
malfunction.
Page 6
2 - HEAD HOLDER WITH FOCUSING MECHANISM
3 - SUPPORT ROD FOR LCD
3.0 UNPACKING AND ASSEMBLY
Page 7
3.0 UNPACKING AND ASSEMBLY
4 - OPTICAL HEAD WITH BUILT-IN DIGITAL CAMERA
5 - 8’’ TFT LCD SCREEN
Page 8
3.0 UNPACKING AND ASSEMBLY
6 - EYEPIECES WF10X/18MM
7 - LED RING ILLUMINATOR WITH BRIGHTNESS CONTROL
Page 9
3.0 UNPACKING AND ASSEMBLY
9 - DIGITAL CAMERA POWER SUPPLY (OUT: 5,5VDC 200mA)
10 - LCD SCREEN POWER SUPPLY (OUT: 12VDC 2,6A)
8 - LED RING POWER SUPPLY (OUT: 12VDC 0.5A)
Page 10
3.0 UNPACKING AND ASSEMBLY
Assembling the microscope
1. Put the optical head in the head holder and then slide it on the pillar. Tighten the screw on
the back at about half height of the pillar (you can move it later when you focus your sam-
ple).
2. Put the LCD screen on a table with its rear up-facing, then insert the slider of the support
rod all the way up and tighten the two screws.
TIGHTEN THIS SCREW
Table of contents
Languages:
Other Optika Microscope manuals
Optika
Optika XDS-3 User manual
Optika
Optika B-1000 POL User manual
Optika
Optika B-500POL User manual
Optika
Optika B-510 Series User manual
Optika
Optika B-150POL-M User manual
Optika
Optika B-1000FL HBO User manual
Optika
Optika B-500BSp User manual
Optika
Optika B-500DK User manual
Optika
Optika B-350 User manual
Optika
Optika B-510 Series User manual
Optika
Optika IM-2 User manual
Optika
Optika B-500 User manual
Optika
Optika B-383LD1 User manual
Optika
Optika B-150 Series User manual
Optika
Optika LAB-1 User manual
Optika
Optika XDS-3FL User manual
Optika
Optika ECOVISION M-100FL User manual
Optika
Optika IM Series User manual
Optika
Optika XC-100L User manual
Optika
Optika ST-50Led User manual
Popular Microscope manuals by other brands
VWR
VWR VisiScope 384 Series instruction manual
Nikon
Nikon ECLIPSE E200 POL instructions
Leica
Leica DI C800 User's manual & installation instructions
ThermoFisher Scientific
ThermoFisher Scientific Continuµm manual
ThermoFisher Scientific
ThermoFisher Scientific Continuµm manual
Olympus
Olympus SZ61 instructions