Opengear CMS6100 User manual
CMS6100 Monitor Quick Start (Rev 1.0) Page 1
CMS6100
Quick Start Guide
Thank you for purchasing the CMS6100 centralized monitoring system (
Monitor
. This
Quick Start walks you through installation, configuration and local operation. For more
details please refer to the
User Manual
on the CDROM.
Step1 Check kit contents
CMS6100
Monitor
This Quick Start & CD
-
ROM
Power cable
Step 2 Connect the CMS6100 hardware
Plug the CMS6100 into the AC mains
Connect the CMS6100 to your management
network
Step 3 Set up the CMS6100 Monitor
The default Monitor IP Address is
192.168.0.1
(subnet mask
255.255.255.0
. With a web
browser on any computer that is LAN connected to the Monitor:
Enter https://192.168.0.1 into the address bar
Note: The LAN connected computer must have an IP address in the same
network range (192.168.0.xxx as the Monitor. If this is not convenient,
you can use the
ARP Ping
command to set the IP address (refer
User
Manual
or online FAQ for details . The Monitor also has its DHCP client
enabled by default, so it will automatically accept any network IP
address assigned by any DHCP server on your network – and will then
respond at both 192.168.0.1 and its DHCP address.
Log in using the default system user name
root
and the default password
default.
An Opengear Welcome screen listing the basic configuration steps is
displayed
CMS6100 Monitor Quick Start (Rev 1.0) Page 2
Select Configure: System A ministration and enter and confirm a new
System Passwor
You may also wish to enter a System Name and System Description to give
the CMS6100 a unique ID and make it simple to identify. Click Apply
To assign the CMS6100 Monitor a new static IP address or to permanently
enable DHCP, select Configure: Network Settings then Network Interface
and check DHCP or Static for Configuration Metho
Step 4 Configure managed console servers
Select Configure: Manage Console Servers. The
Managed Console
Server
list shows all the console servers currently being monitored. The
Detected Managed Console Servers
drop down list also shows all the detected
console servers not currently being monitored
To add a console server to either select one from the drop down list or add
the new console server’s IP Addresses and click A
Enter IP A ress, Description and Name for the
Managed Console Server
you are adding
Enter the Remote
Root
Passwor (i.e. the System Password that has been
set on this remote
Managed Console Server
Note: This password is used to propagate auto generated SSH keys and then
forgotten. This password will not be stored. The CMS6100
Monitor
communicates with the local and remote
Managed Console Servers
with
secure SSH connections. This is done using public key authentication
CMS6100 Monitor Quick Start (Rev 1.0) Page 3
and the
Opengear Monitor
automatically generates SSH key pairs for
these communications - rather than using passwords -ensuring secure
authenticated communications
Click Apply and the Monitor
will set up a secure tunnel to the remote
Managed Console Server
and upload all its configuration settings (managed
device details, user accounts, PDU and UPS settings, serial console and
environmental alerts etc
Step 5 uthorize added new users
Monitor retrieves all the user accounts from each
Managed Console Server
but does not
automatically give any of them any access privileges to the Monitor
itself (only the
root
user has access by default .
Select Configure: User Authorization. This will display a list of all the user
which have been set up on all the
Managed Console Servers
currently being
monitored by the
Opengear Monitor
For any user then select E it and enter a new password that will be used by
that user when accessing the Monitor. You may also wish to modify the
Group
membership and
Description
associated with the authorized user.
Users in the user group can access the all the monitoring screens/menus
whereas users in the a min group have this access plus the ability to
reconfigure using the
Configure
menu
Click Apply
Step 6 Configure date and time
It is recommended that you set the local Date and Time as
logging entries are time-
stamped (and certificate generation needs to check the validity period
Select Configure: Date & Time and set manually or select synchronizing with
a remote time server using the Network Time Protocol (NTP
Step 7 Certificate update
The default SSL certificate that comes with Monitor device is for initial set up purpose
and should not be relied on for secured global access (and when you initially https://
accessed the Monitor your browser may have responded with a message that verified the
security certificates validity but noted that it is not necessarily verified by a certifying
authority. So it is recommended you generate and install a new base64 X.509 certificate
that is unique for you.
Select System: SSL Certificate, fill out the fields and click on Generate CSR for the
Certificate Signing Request (CSR
Downloa the CSR string and send it to a Certification Authority (CA for certification. They
will return you a new certificate which you can then Uploa to Monitor
CMS6100 Monitor Quick Start (Rev 1.0) Page 4
Step 8 Commence monitoring
Monitor runs Nagios (www.nagios.org and the
Current Status
,
Reports
and
System
menu show
the status and history of all the applications, computers and devices in your distributed networks
- highlights problems and giving warnings
To remedy identified problems simply click on the Connect or Manage
Power or View Status/Logs button. Your browser will download a
configured
SDT Connector
Java application from the CMS6100 Monitor which
will run on your computer and securely connect you to the relevant screen on
the
Managed Device
or
Managed Console Server
Other Opengear Measuring Instrument manuals
