Olympus BXFM Series User manual
INSTRUCTIONS
BXFM
FOCUSING UNIT
A X 7 6 1 3
This instruction manual is for the Olympus Focusing Unit model BXFM and associated modules.
To ensure safety, optimum performance and familiarize yourself fully with the use of the assembled
microscope, we recommend that you study this manual thoroughly before operating the unit. Re-
tain this instruction manual in an easily accessible place near the work desk for future reference.
This publication is printed on 100% recycled paper
BXFM
CONTENTS
4
5,6
7, 8
9-13
IMPORTANT — Be sure to read this section for safe use of the equipment. —
1 SYSTEM DIAGRAM
2 NOMENCLATURE
3
4 USING THE CONTROLS
REFLECTED LIGHT BRIGHTFIELD OBSERVATION PROCEDURE
4-1 Base and Power Supply............................................................................................................................................................... 9
4-2 Focusing Unit ........................................................................................................................................................................................... 10
1Voltage Indication 2Placing the Specimen
4-3 Observation Tube ......................................................................................................................................................................... 11,12
4-4 Reflected Light Illuminator (U-KMAS) .................................................................................................................... 13
14-16
1Adjusting the Interpupillar Distance 2Adjusting the Diopter
3Using the Eye Shade 4Using Eyepiece Micrometer Disks
5Selecting the Light Path of Trinocular Tube 6
Adjusting the Tilt (with the U-TBI3/SWETTR2)
1Using the Filters
1
Adjusting the Coarse Adjustment Knob Tension
2
Using the Rubber Fine Adjustment Knob Cap
1-3
Correct assembly and adjustments are critical for the microscope to exhibit its full performance. If you are going to
assemble the microscope yourself, please read chapter 10, “ASSEMBLY” (pages 24 to 27) carefully.
6 TROUBLESHOOTING GUIDE
7 SPECIFICATIONS
8 MAIN DIMENSION DIAGRAM
9 OPTICAL CHARACTERISTICS «UIS2 (UIS) Series»
10
PROPER SELECTION OF THE POWER SUPPLY CORD ....................................................................... 28,29
ASSEMBLY
—
See this section for the replacement of the light bulb. —
5-1 Reflected Light Brightfield Observation............................................................................................................. 14
5-2 Reflected Light Nomarski DIC Observation .......................................................................................14-16
5-3 Reflected Light Simplified Polarized Light Observation ............................................................ 16
5 OBSERVATION METHODS (Using U-KMAS)
17,18
19
20,21
22,23
24-27
1
IMPORTANT
The BXFM focusing unit can be used as the basis for installing modules such as reflected light illumina-
tion equipment, objectives, eyepieces and observation tube for construction of a microscope system.
The BXFM can be installed on the exclusive stand or on your microscope.
SAFETY PRECAUTIONS
1. Install the microscope on a sturdy, level table or bench so as not to
block the air vents on the underside of the base.
2. When combing the stand (U-ST), install the BXFM so that it forms an
angle of ±30° with respect to the pillar as shown in Fig. 1.
The compact brightfield illuminator (U-KMAS) should be installed so that,
when it is seen from the front, the lamp housing is located on its right
side.
3. When carrying the BXFM, hold the stand by the bottom with one hand
as shown in Fig. 2, and hold the focusing block with the other hand.
# Do not hold the BXFM by the coarse/fine adjustment knobs or lamp
housing. Otherwise, the microscope may be damaged.
4. The surface of the lamp housing @ on the rear of the microscope be-
comes very hot. When installing the microscope system, leave spaces
of more than 10 cm around the lamp housing, particularly on the top
and bottom.
Do not install the lamp housing up side down or with the side facing up.
Also do not use the microscope in a tilted attitude.
5. The TH4 power supply is air-cooled so it becomes during operation.
When installing it, leave spaces of more than around it. Also make sure
to distribute cables away from the power supply.
6. Be sure to set the main switch to “ ” (OFF) and unplug the power cord
before replacing the light source bulb. (P. 26)
7. Always use the power cord provided by Olympus. If no power cord is
provided, please select the proper power cord by referring to the chapter
“PROPER SELECTION OF THE POWER SUPPLY CORD” at the end of
this instruction manual. If the proper power cord is not used, product
safety and performance cannot be guaranteed.
8. Always ensure that the grounding terminal of the microscope and that
of the wall outlet are properly connected. If the equipment is not grounded,
Olympus can no longer warrant the electrical safety and performance of
the equipment.
Fig. 1
Fig. 2
Front
Back
2
BXFM
Illuminator
Mounting Holder BXFM-ILHS BXFM-ILH
Standard
Combination
Weight (Module
Names)
7.5 kg
BX-RLA2, U-TR30-2,
U-LH100-3, revolving
nosepiece, objec-
tives, eyepiece
Additional Load
Limit 2.8 kg
4.0 kg
When the BXFM-
ILHSPU counter
spring is used
5.2 kg
U-KMAS, U-TR30-2,
U-LH100-3, revolving
nosepiece, objec-
tives, eyepiece
· With the combination using the BXFM-ILH illuminator mounting holder,
do not use the U-ST stand because this makes the system unstable.
· The system can be stabilized by using the SZ-STL large stand, but the
image may fluctuate or blur irregularly when a 50X or higher-power ob-
jective is used.
· It is recommended to fabricate an exclusive clamping tool which uses
the support mounting hole (P. 20) or module mounting screw hole of the
BXFM-F focusing unit.
Symbol Explanation
The following symbols are found on the microscope. Study the meaning of the symbols and always use the equip-
ment in the safest possible manner.
Indicates that the surface becomes hot, and should not be touched with bare hands.
Before use, carefully read the instruction manual. Improper use could result in personal injury to
the user and/or damage to the equipment.
Indicates that the main switch is ON.
Indicates that the main switch is OFF.
Warning engraving/stickers are placed at parts where special precaution is required when handling and using the
microscope. Always heed the warnings.
Warning engraving
position
Lamp housing
(Warning against high temperature)
l
Safety Symbols
Warnings
9. When using a photographic unit or TV camera, be sure to observe the
total weight limit of the modules added to the standard combination as
shown below.
3
1Getting Ready
1. A microscope is a precision instrument. Handle it with care and avoid subjecting it to sudden or severe impact.
2. Do not use the microscope system where it is subjected to direct sunlight, high temperature and humidity, dust or
vibrations. (For the operating conditions, refer to chapter 7, “SPECIFICATIONS”.)
3. One intermediate attachment can be used by installing U-CA magnification changer or U-EPA2 eyepoint adjuster above
the reflected light illuminator.
2Maintenance and Storage
1. To clean the lenses and other glass components, simply blow dirty away using a commercially available blower and wipe
gently using a piece of cleaning paper (or clean gauze).
If a lens is stained with fingerprints or oil smudges, wipe it gauze slightly moistened with commercially available absolute
alcohol.
Since the absolute alcohol is highly flammable, it must be handled carefully.
Be sure to keep it away from open flames or potential sources of electrical sparks –– for example, electrical
equipment that is being switched on or off.
Also remember to always use it only in a well-ventilated room.
2. Do not attempt to use organic solvents to clean the microscope components other than the glass components. To clean
them, use a lint-free, soft cloth slightly moistened with a diluted neutral detergent.
3. Never attempt to disassemble any part of the microscope system.
4. When not using the microscope, set the main switch to “ ” (OFF). After making sure the lamp housing has cooled down
sufficiently, cover it with a dust cover.
5. When disposing of this product, check the regulations and rules of your local government and be sure to observe them.
3Caution
If the microscope is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition,
the equipment may also be damaged. Always use the equipment as outlined in this instruction manual.
The warning, caution and other notes in this manual use the following symbols.
: Indicates that failure to follow the instructions in the warning could result in bodily harm to the
user and/or damage to equipment (including objects in the vicinity of the equipment).
# : Indicates that failure to follow the instructions could result in damage to equipment.
} : Indicates commentary (for ease of operation and maintenance).
4
BXFM
1
SYSTEM DIAGRAM
}This instruction manual gives description the modules which are connected in thick and broken lines in the following
diagram. For other modules, please refer to their instruction manuals.
*Reflected Light Lamp Housing
Halogen bulb:
U-LH100-3
(Power Supply TH4)
Mercury burner:
U-LH100HG
U-LH100HGAPO
Xenon burner:
U-LH75XEAPO
** For the modules without the model names, consult your dealer or the latest catalogues.
Eyepiece**
Module support
pillar or module
mounting block
Reflected
Light Lamp
Housing*
Reflected Light
Illuminator
BX-URA2
BX-RLA2 Revolving
Nosepiece**
Objective**
Illuminator
Mounting Holder
BXFM-ILH
Revolving
Nosepiece**
Objective**
Illuminator
Mounting
Holder S
BXFM-ILHS
Large Stand
SZ-STL
Observation Tube**
Intermediate tube**
Compact Reflected
Light Brightfield Illuminator
U-KMAS
Reflected Light
Lamp Housing*
Focusing Unit
BXFM-F
Counter Spring
BXFM-ILHSPU
Stand
U-ST
5
NOMENCLATURE
Focusing Unit BXFM-F
Compact Reflected Light Brightfield Illuminator U-KMAS
Observation tube mount
Illuminator Mounting Holder S BXFM-ILHS
}The U-KMAS reflected light illuminator can be mounted.
U-KMAS mount
*Used when the BX-RLA2 or BX-URA2 illuminator is
combined with the focusing unit. (P. 27)
Fine adjustment knob
Pillar mounting hole
Revolving nosepiece mount dovetail
Analyzer insertion slot
Polarizer insertion slot
Lamp housing mount
Filter insertion slot
Coarse adjustment knob
Coarse adjustment knob
tension adjustment ring
Coarse adjustment knob
Fine adjustment knob
Rubber fine adjustment knob cap
BXFM-ILHSPU counter spring mounting screw hole
Auxiliary centering screws*
( 32 mm)
6
BXFM
Illuminator Holder BXFM-ILH, Counter Spring BXFM-ILHSPU
}The BX-URA2 or BX-RLA2 reflected light illuminator can be installed. The BXFM-ILHSPU is used to reduce the load on
focusing due to the weight of the reflected light illuminator and its accessories.
Illuminator mount screw holes
Stand U-ST Pillar Power Supply TH4
POWER LED
Hand Switch TH4-HS
Brightness control knob
Mounting holes x 4
Specimen holder
Stage plate
REMOTE LED
Main switch Brightness control knob
Lamp ON-OFF switch
“ I”: ON, “ ”: OFF
7
REFLECTED LIGHT BRIGHTFIELD OBSERVATION
PROCEDURE
}The following flow chart pertains only to the reflected light brightfield observation which is the most basic operation. The
procedures for the polarized light and Nomarski DIC operations will be described in their respective sections.
(Controls Used) (Page)
Set the main switch to “ I” (ON).
Disengage the analyzer, polarizer,
filter, etc. from the light path.
Select the light path (only when a trinocular
tube is used).
Place the specimen on the stage plate.
Engage the 10X objective in the light path.
Bring the specimen in focus.
Adjust the brightness.
Adjust the interpupillary distance.
Adjust the diopter.
Engage the desired objective in the light path
and bring the specimen in focus.
Insert the required filters.
Adjust the brightness.
Start observation.
@Main switch (P. 9)
²Lamp ON-OFF switch
³Brightness control knob
Light path selector knob (P. 12)
|Specimen holder (P. 9)
ƒRevolving nosepiece
…Coarse/fine adjustment knobs (P. 10)
³Brightness control knob (P. 9)
†Binocular tube (P. 11)
‡Diopter adjustment ring (P. 11)
ƒRevolving nosepiece
…Coarse/fine adjustment knobs (P. 10)
ŠFilter insertion slot (P. 13)
³Brightness control knob (P. 9)
This manual suits for next models
2
Table of contents
Other Olympus Microscope manuals
Olympus
Olympus SZ61 User manual
Olympus
Olympus BX45 User manual
Olympus
Olympus Fluoview-1000 User manual
Olympus
Olympus BX3-SSU User manual
Olympus
Olympus K Operating instructions
Olympus
Olympus VANOX User manual
Olympus
Olympus FH User manual
Olympus
Olympus CH Series Operating instructions
Olympus
Olympus fsx100 User manual
Olympus
Olympus MIC-D Operating instructions
Olympus
Olympus CX23 User manual
Olympus
Olympus BH2-CH Substage User manual
Olympus
Olympus CX40 User manual
Olympus
Olympus U-DA User manual
Olympus
Olympus BX-RFAA User manual
Olympus
Olympus bx40 User manual
Olympus
Olympus BX53M-P User manual
Olympus
Olympus BX3-URA User manual
Olympus
Olympus VMF Operating instructions
Olympus
Olympus BHS User manual
Popular Microscope manuals by other brands
VWR
VWR VisiScope 384 Series instruction manual
Nikon
Nikon ECLIPSE E200 POL instructions
Leica
Leica DI C800 User's manual & installation instructions
ThermoFisher Scientific
ThermoFisher Scientific Continuµm manual
ThermoFisher Scientific
ThermoFisher Scientific Continuµm manual
Leica
Leica FL560 user manual