NXP Semiconductors QN9090-DK006 User manual

UM11355

QN9090-DK006 Development Kit User Guide

Rev.1.0 —15 January 2020

Document information

Info

Content

Keywords

QN9090 DK, User Guide

Abstract

This document is a user guide for the QN9090 Development Kit

NXP Semiconductors

QN9090

QN9090-DK006 Development Kit User Guide

UM11355

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.1.0 —15 January 2020

2 of 19

Contact information

For more information, please visit: http://www.nxp.com

Revision history

Rev

Date

Description

1V0

20200115

Initial release

NXP Semiconductors

QN9090

QN9090-DK006 Development Kit User Guide

UM11355

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.1.0 —15 January 2020

3 of 19

1. Introduction

QN9090 DK is designed for QN9090 IC evaluation and development. It is very

convenient to evaluate QN9090’s functions and performance. There are also some

useful peripherals, like GPIOs, and Arduino interface. J-Link and J-Trace functions are all

supported for debugging QN9090. ISP download function is also contained and very

easy to use.

1.1 Purpose

This document introduces all functions of QN9090 DK. Descripts all parts of QN9090 DK

boards in detail.

1.2 Kit contents

QN9090 DK includes the following three boards:

•Carrier Main Board

•QN9090 Module board

•Generic expansion board

Figure 1 Board overview

NXP Semiconductors

QN9090

QN9090-DK006 Development Kit User Guide

UM11355

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.1.0 —15 January 2020

4 of 19

2. Carrier Main Board

The OM15076 also called DK6 QN9090 carrier board provides a flexible development

system for NXP’s QN9090 ultra-low power, high performance wireless microcontroller. It

can be used with a wide range of development tools, including NXP’s MCUXpresso IDE.

It has been developed by NXP to enable evaluation and prototyping with the

QN9090_30_T Bluetooth Low Energy wireless microcontroller.

The carrier boards (part number: OM15076) supplied in the development kit are

physically identical. They are all pre-fitted with an Arduino-compatible expansion board

and a QN9090-based module with integrated antenna.

2.1 Feature summary

The QN9090 Carrier board includes the following features:

•QN9090 module site

•NFC Tag with printed antenna

•On-board, high-speed USB based, Link2 debug probe with ARM’s CMSIS-DAP

and SEGGER J-Link protocol options.

•Link2 probe can be used with on-board QN9090 or external target.

•Support for external debug probes.

•Power, Reset, ISP and UART Tx/Rx LEDs.

Figure 2 Carrier Main Board

NXP Semiconductors

QN9090

QN9090-DK006 Development Kit User Guide

UM11355

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.1.0 —15 January 2020

5 of 19

•Target Reset, and User buttons.

•Expansion options based on Arduino R3, plus additional expansion port pins.

•On-board 3.3V from USB port, 4xAAA batteries, 2xAAA batteries (low-power

mode) or external power supply options.

•Built-in power consumption measurement.

•UART, I2C and SPI port bridging from LPC4233 target to USB via the on-board

debug probe.

•8Mb Macronix MX25R QSPI flash.

•FTDI USB connector.

2.2 Board layout and settings

This section provides a quick reference guide to the main board components,

configurable items, visual indicators and expansion connectors. The layout of the

components on the QN9090 Carrier board is shown in Figure 3.

The function of each identified component is listed in Table 1

Table 1. Table Board interface components

Circuit ref

Description

Link2 LPC4322 BOOT0_LED indicator. Reflects the state of LPC43xx Link2

MCU P1_1. When the boot process fails, D1 will toggle at a 1 Hz rate for 60

seconds. After 60 seconds, the LPC4322 is reset.

DS1

QN9090 Power LED

DS2, DS3

2x Red debug LEDs connected respectively to QN9090 PIO_0 (DS2) and

PIO_3 (DS3). LEDs are on anytime the PIO is low.

DS4

QN9090 Reset LED –LED is on anytime the Target RESET is pulled low.

Figure 3 Carrier board layout

NXP Semiconductors

QN9090

QN9090-DK006 Development Kit User Guide

UM11355

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.1.0 —15 January 2020

6 of 19

DS5, DS6

Green LEDs connected respectively to UART0_Tx (DS5) and UART0_Rx

(DS6).

DS8

In System Programming (ISP) LED indicator. LED is ON when SW2 button is

pressed.

IC2

Link2 MCU

FTDI serial header. In addition to provide a serial output from QN9090, the

Target side of the board can be powered from the FTDI header. The QN9090

supports serial ISP boot from the FTDI header.

32 pins Expansion header connector for debug. All the QN9090 IOs from

modules and more are available here.

J14

QN9090 VBAT current monitor V sense measurement. The V sense can be

measured with a volt meter. Pin 1 (square pad) is positive and pin 2 is

negative. QN9090 current is calculated by dividing the measured voltage at

J14 by the V sense resistance value of 3.3Ω.

J15

Link2 mini USB B-type connector. Powers both the Link2 side of the board

and depending on the JP3, J5 configuration, the QN9090 Target side of the

board. Power the board from this connector when using the on-board debug

probe to debug the QN9090 Target MCU.

QN9090 Target SWD disable –2-position jumper pins.

1. Jumper “ON” (default) the QN9090 Target SWD interface enabled.

Normal operating mode where the Target SWD is connected to

either the on-board

2. Link2 debug probe or an external debug probe. Jumper “OFF”, the

QN9090 Target SWD interface is disabled. Use this setting only

when the on-board Link2 debug probe is used to debug an off-board

Target QN9090.

SWD interface buffer power selection

QN9090 power source selection

1. Jumper fitted in position pin 1 - 2 (default -5V REG). Power source

is either 5V from mini USB connector or FTDI connector, or 4.5V

from 3xAAA batteries or 5V from a 7-12V DC power supply

connected on J4.

2. Jumper fitted in position pin 2 - 3 (BAT 6V). Power source is 4xAAA

batteries.

See details on Board power diagram Figure 5

Jumper to route LPC or FTDI to UART RX0 QN9090 (to change in pair with

JP7)

Link2 (LPC4322) force DFU boot –2 position jumper pins.

1. Jumper open (default) or shunted to boot mode for Link2 to follow

the normal boot sequence. The Link2 will boot from internal flash if

image is found there. With the internal flash erased the Link2 normal

boot sequence will fall through to DFU boot.

2. Jumper shunted to force the Link2 to DFU boot mode. Use this

setting to reprogram the Link2 internal flash with a new image or to

use the MCUXpresso IDE with CMSIS-DAP protocol.

JP6 is used to isolate the Link2 debug probe (SPI bridge function) from the

QN9090 target to prevent leakage current in power critical applications /

current consumption analysis. JP6 needs to be fitted in position 1 - 2 to use

the SPI bridging function between the QN9090 and Link2. This jumper is not

fitted by default

Jumper to shunt LPC to QN9090 or FTDI to UART TX0 QN9090 (to change

in pair with JP4)

CN1, CN2,

CN3, CN4

Expansion connectors, including Arduino Uno rev3 compatible connectivity.

JM1, JM2

QN9090 module headers

NXP Semiconductors

QN9090

QN9090-DK006 Development Kit User Guide

UM11355

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.1.0 —15 January 2020

7 of 19

10-pin SWD connector –The SWD connector is used to debug the QN9090

Target from an external debug probe. The same SWD connector can also be

used to connect the on-board Link2 debug probe to an off-board target MCU

(for this JP1 must be shunted).

BP1

User Interface button connected to IO1. Used in some Applications Notes.

SW2

In System Programming (ISP) button. QN9090 will enter ISP mode when

SW2 is pressed during hardware reset.

SW4

QN9090 Reset pushbutton.

To ease the board usage and any debug the connectors serigraphy is also copied on PCB bottom.

J7, J13, J12 & J11 battery slots are also here.

2.3 LED indicators

The DK6 board LED location are shown in Figure 3. A description of each on-board LED

indicator is shown in next table

Table 2. LED indicator functions

LED reference

Description

Link2 MCU BOOT0_LED indicator. Reflects the state of Link2 MCU

P1_1. When the boot process fails, D1 will toggle at a 1 Hz rate for 60

seconds. After 60 seconds, the Link2 MCU is reset. It will be ON when

the Link2 MCU is Booting using DFU (See description for JP5).

DS1

QN9090 Power LED. This LED is on any time power is applied to the

QN9090 wireless MCU.

DS2, DS3

2x Red debug LEDs connected respectively to QN9090 PIO_0 (DS2)

and PIO_3 (DS3). LEDs are on anytime the respective PIOs from the

QN9090 are pulled low.

DS4

QN9090 Reset LED –LED is on anytime the Target RESET is pulled

Figure 4 OM15076 DK6 PCB bottom view

NXP Semiconductors

QN9090

QN9090-DK006 Development Kit User Guide

UM11355

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.1.0 —15 January 2020

8 of 19

low.

DS5, DS6

2x Green LEDs connected respectively to UART0_Tx (DS5) and

UART0_Rx (DS6). LEDs will flash any time there is activity on the

UART0.

DS8

In System Programming (ISP) LED indicator. LED is ON when IO5_ISP

is pulled low and when SW2 button is pressed.

2.4 ARDUINO connectors

ARDUINO compatible connectors are based on Arduino R3.

References on the DK6 board are CN1, CN2, CN3, CN4.

The Generic expansion board OM15082 can be plugged into these connectors.

2.5 Buttons

2.5.1 Reset button

This button (SW4) is used to reset the QN9090 (note that the Link2 is NOT reset by this

button)

2.5.2 ISP button

This button connects the QN9090_PIO5 (ISP_Entry) pin to ground. This should be used

to set the QN9090 in ISP mode to program a binary file into the chip memory.

To force entry into this ISP mode, hold down the ISP button (SW2), press and release

the Reset button (SW4), then release the ISP button (SW2). This is done automatically

when using the DK6 Production Flash programmer with J2 (FTDI USB interface)

2.6 User Interface button

This button (BP1) is connected to QN9090_PIO_1 and should be used as an input

2.7 QN9090 Serial port

The QN9090 UART0 can also be connected through a virtual communication port

(VCOM) UART bridge Link2 function either to a host computer connected to the J2 USB

FTDI or to J15 USB Link2. By default, the DK 6 is configured to use the FTDI USB.

For Link2 USB: The factory default CMSIS-DAP Link2 image includes UART bridge

functionality (VCOM support), and this firmware is also available with the LPCScrypt

utility, available at https://www.nxp.com/design/microcontrollers-developer-resources/lpc-

microcontroller-utilities:LPC-UTILITIES power connections and measurements.

For the USB FTDI, the PC driver is available on FTDI website (the FTDI chip is already

configured before the carrier board release).

2.8 Board power connections

A block diagram of the board power tree is shown in Figure 5. When the QN9090 Target

is to be debugged from the on board Link2 probe, the USB mini B-type connector (J15)

NXP Semiconductors

QN9090

QN9090-DK006 Development Kit User Guide

UM11355

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.1.0 —15 January 2020

9 of 19

must connected to a Host computer. When the QN9090 Target is to be debugged from

an external debug probe, instead of the on-board debug probe, the Link USB connector

(J15) must be disconnected.

The QN9090 Target VBAT selection is made at JP3, J5, with 3.3V from on-board LDO

set as the default.

2.9 Debug Configurations

The DK6 board has a built-in debug probe referred to as “Link2”. The QN9090 target

wireless MCU can be debugged by the Link2 debugging probe, or from an external

debug probe installed at P1. On-board jumpers JP1 and JP2 must be correctly positioned

for each mode. The on-board Link2 debug probe is capable of debugging target MCU’s

with a VDDIO range of 1.6V to 3.6V. Check the sections below for the appropriate jumper

settings and how to properly power the board.

2.9.1 Debug using on-board debug probe

To use the on-board Link debug probe:

•The jumper JP2 must be fitted in position pin 1 - 2 (Local Target).

•Jumper JP1 must be open or fitted in position 2 –3 to enable the target

QN9090.

•Connecting the mini USB J15 to a host computer will power the Link and

according JP3, J5 position, the QN9090 sections of the board and provide

the USB link to the debug tool software.

2.9.2 Debug using external debug probe

To use an external debug probe:

•connect the probe to the SWD (P1) connector

Figure 5 Board power diagram

NXP Semiconductors

QN9090

QN9090-DK006 Development Kit User Guide

UM11355

All information provided in this document is subject to legal disclaimers.

User Guide

Rev.1.0 —15 January 2020

10 of 19

•power the QN9090 Target section of the board from the FTDI header (J1)

or the Jack connector (J4)

•and fit a jumper to JP2 across pin 1 - 2 (Local Target).

•Jumper JP1 must be open or fitted across pin 2 –3 to enable the target

QN9090.

•The on-board Link2 debug probe must be unpowered, by leaving USB mini

(J15) unconnected.

2.9.3 On-Board Link2 flash programing

To program the Link2 Flash the Link2 MCU must be in DFU mode. If the Link2 already

has a valid image in the flash, you will need to force it into DFU mode by placing a

jumper shunt on JP5 across pin 1 - 2, then power the board by connecting the mini USB

J15 to a host computer. Link2 MCU programming is performed using the LPCScrypt

utility (see https://www.nxp.com/design/microcontrollers-developer-resources/lpc-

microcontroller-utilities:LPC-UTILITIES). Instructions for using the tool are located at the

same web page.

2.9.4 Using the DK6 to debug an off-board target

The DK6 board’s Link2 debug probe may be used to debug an off-board target MCU.

The on-board Link2 debug probe is capable of debugging target MCU’s with a VDDIO

range of 1.6V to 3.6V. To keep the on-board target QN9090 MCU from interfering with

the SWD interface:

•JP1 must be fitted across pin 1 - 2.

•The Link2 debug probe SWD is connected by a ribbon cable between the

P1 connector to the off-board target MCU SWD interface.

•Power the DK6 board from the Link USB connector J15,

•Fit jumper JP2 across pins 2 - 3 (External Target).

Table of contents

Other NXP Semiconductors Microcontroller manuals

NXP Semiconductors

NXP Semiconductors ASUG User manual

NXP Semiconductors

NXP Semiconductors LPC29 Series User manual

NXP Semiconductors

NXP Semiconductors i.MX 8M PLUS EVK User manual

NXP Semiconductors

NXP Semiconductors S32R372141EVB User manual

NXP Semiconductors

NXP Semiconductors A1006 User manual

NXP Semiconductors

NXP Semiconductors TWR-K60N512-IAR User manual

NXP Semiconductors

NXP Semiconductors MPC574 P Series User manual

NXP Semiconductors

NXP Semiconductors MC9S08LG32 User manual

NXP Semiconductors

NXP Semiconductors MPC5606BK User manual

NXP Semiconductors

NXP Semiconductors OM-SE051ARD User manual

NXP Semiconductors

NXP Semiconductors SLN-LOCAL2-IOT User manual

NXP Semiconductors

NXP Semiconductors HCS12 User manual

NXP Semiconductors

NXP Semiconductors MC9S12ZVMB-Family User manual

NXP Semiconductors

NXP Semiconductors LPC5500 Series Reference manual

NXP Semiconductors

NXP Semiconductors QN9080 User manual

NXP Semiconductors

NXP Semiconductors LPC11E Series User manual

NXP Semiconductors

NXP Semiconductors LPC1549 User manual

NXP Semiconductors

NXP Semiconductors LPC29 Series User manual

NXP Semiconductors

NXP Semiconductors freescale K51 Series User manual

NXP Semiconductors

NXP Semiconductors S12ZVMAEVB User manual

NXP Semiconductors

NXP Semiconductors SLN-VIZNAS-IOT User manual

NXP Semiconductors

NXP Semiconductors FRDM-KW24D512 User manual

NXP Semiconductors

NXP Semiconductors MC9S08SU16 User manual

NXP Semiconductors

NXP Semiconductors MTRCKTSPS5744P User manual

Popular Microcontroller manuals by other brands

AMS

AMS AS7261 Demo Kit user guide

Novatek

Novatek NT6861 manual

Espressif Systems

Espressif Systems ESP8266 SDK AT Instruction Set

Nuvoton

Nuvoton ISD61S00 ChipCorder Design guide

STMicrolectronics

STMicrolectronics ST7 Assembler Linker user manual

Texas Instruments

Texas Instruments Chipcon CC2420DK user manual

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM user guide

NEC

NEC 78GK0S/K 1+ Series Application note

Mikroe

Mikroe SEMITECH N-PLC Click Application note

Intel

Intel Agilex user guide

Cypress

Cypress CY4607 HX2VL quick start guide

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE manual

Texas Instruments

Texas Instruments TMS320F2837 D Series Workshop Guide and Lab Manual

CYPRES

CYPRES CY14NVSRAMKIT-001 user guide

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM user guide

Espressif Systems

Espressif Systems ESP8266EX Programming guide

Abov

Abov AC33M8128L user manual

Laird

Laird BL654PA user guide