National Instruments 4350 User manual

CVI™, LabVIEW™, Measurement Studio™, National Instruments™, NI™, ni.com™, and NI-DAQ™ are trademarks of

National Instruments Corporation. Product and company names mentioned herein are trademarks or trade names of

their respective companies. For patents covering National Instruments products, refer to the appropriate location:

Help»Patents in your software, the patents.txt file on your CD, or ni.com/patents.

October 2002

321562D-01

WHERE TO START WITH THE NI 435X

This document explains how to begin using the National Instruments

4350/4351 (NI 435X) high-precision data acquisition (DAQ) temperature

and voltage meters for PCMCIA, USB, PCI, and PXI/CompactPCI buses.

Conventions

The following conventions are used in this document:

»The »symbol leads you through nested menu items and dialog box options

to a final action. The sequence File»Page Setup»Options directs you to

pull down the File menu, select the Page Setup item, and select Options

from the last dialog box.

♦The ♦symbol indicates that the following text applies only to a specific

product, a specific operating system, or a specific software version.

This icon denotes a note, which alerts you to important information.

This icon denotes a caution, which advises you of precautions to take to

avoid injury, data loss, or a system crash. When this symbol is marked on

the product, refer to the Read Me First: Safety and Radio-Frequency

Interference document, shipped with the product, for precautions to take.

bold Bold text denotes items that you must select or click in the software, such

as menu items and dialog box options. Bold text also denotes parameter

names.

italic Italic text denotes variables, emphasis, a cross reference, or an introduction

to a key concept. This font also denotes text that is a placeholder for a word

or value that you must supply.

monospace Text in this font denotes text or characters that you should enter from the

keyboard, sections of code, programming examples, and syntax examples.

This font is also used for the proper names of disk drives, paths, directories,

ni.com

Where to Start with the NI 435X 2 ni.com

programs, subprograms, subroutines, device names, functions, operations,

variables, filenames and extensions, and code excerpts.

NI 435XRefers to all devices in the National Instruments 4350 and 4351 families.

Unpacking the Kit

Follow the unpacking instructions below that correspond to the

NI 435Xdevice.

♦NI PCMCIA-4350

The NI PCMCIA-4350 is shipped in an antistatic vinyl package; when you

are not using the NI PCMCIA-4350, store it in the antistatic vinyl package.

Because the NI PCMCIA-4350 is enclosed in a fully shielded package,

no additional electrostatic discharge (ESD) precautions are necessary.

However, for your own safety and to protect the NI PCMCIA-4350, never

touch the connector pins.

♦NI PXI-4351 and NI PCI-4351

The NI PXI-4351 and NI PCI-4351 ship in antistatic vinyl packages that

prevent electrostatic damage to the device. ESD can damage several

components on the device. To avoid such damage when handling the

device, take the following precautions:

• Ground yourself using a grounding strap or by holding a grounded

object.

• Touch the antistatic package to a metal part on the computer chassis

before removing the device from the package.

• Remove the device from the package and inspect the device for loose

components or any other sign of damage. Notify NI if the device

appears damaged in any way. Do not install a damaged device in the

computer.

•Never touch the exposed connector pins.

•Donot touch the printed circuit board or any components on the board

because this may affect performance of the device.

Caution The NI PXI-4351 and NI PCI-4351 are ESD/contamination sensitive. Handle the

board using the edges or metal bracket.

♦NI USB-4350

The NI USB-4350 is shipped in an antistatic vinyl package; when you are

not using the NI USB-4350, store it in the antistatic vinyl package. Because

the NI USB-4350 is enclosed in a fully shielded package, no additional

©National Instruments Corporation 3 Where to Start with the NI 435X

ESD precautions are necessary. However, for your own safety and to

protect the NI USB-4350, never touch the connector pins.

What You Need to Get Started

To set up and use the NI 435Xdevice, you need the following items:

❑A computer

❑One of the following NI 435Xhigh-precision DAQ devices:

– NI PCMCIA-4350

– NI USB-4350

– NI PXI-4351

– NI PCI-4351

❑NI-DAQ 6.9.3 or higher for PC compatibles

❑Logger Soft Front Panel 1.0.1 or higher

❑If you want to program with the device, use one of the following

software packages and documentation:

– LabVIEW 6.1 or later

– Measurement Studio LabWindows™/CVI™4.0 or later

– Measurement Studio for Visual Basic

– Third-party compiler

❑Optional cables and accessories

❑Read Me First: Safety and Radio-Frequency Interference

❑VI Logger Soft Front Panel Note to Users

❑Getting Started with VI Logger

Installing the Software

Install NI-DAQ and the application software before you install the

NI 435Xdevice. If you are using LabVIEW, Measurement Studio

LabWindows/CVI, or Measurement Studio for Visual Basic, refer to their

software release notes for installation instructions. If you are using

programming languages such as Visual Basic, C, or C++ with NI-DAQ,

follow the NI-DAQ release note instructions for installing third-party

compilers.

Where to Start with the NI 435X 4 ni.com

Complete the following steps to install the NI 435Xsoftware, which

includes NI-DAQ 6.9.3, Logger Soft Front Panel 1.0.1, and the NI 435X

instrument driver:

1. Insert the NI-DAQ 6.9.3 installation CD. Follow the instructions that

appear on the screen.

2. Insert the Logger Soft Front Panel 1.0.1 and NI 435Xinstrument driver

CD. Follow the instructions that appear on the screen.

3. Click OK to restart the computer.

After you install the software, you are ready to install the NI 435X

hardware. Refer tothe Installingthe NI435Xsection for further

instructions.

Installing the NI 435X

Caution Refer to the Read Me First: Safety and Radio-Frequency Interference document

before removing equipment covers or connecting/disconnecting any signal wires.

Power off the computer and, depending upon the device type, install the

NI 435Xfollowing the instructions in this section.

Note You can plug in the NI PCMCIA-4350 and NI USB-4350 at any time after the

drivers are installed without powering off the computer.

©National Instruments Corporation 5 Where to Start with the NI 435X

♦NI PCMCIA-4350

Figure 1. NI PCMCIA-4350 System

You can install the NI PCMCIA-4350 in any available Type II PCMCIA

slot in the computer.

Windows 98 or later includes the Plug and Play services that the operating

system uses. Windows NT 4.0 or higher includes the drivers needed to use

PCMCIA cards. The operating system configures the NI PCMCIA-4350

and automatically assigns the base address and the interrupt level. The

following are general installation instructions, but consult the PC user

manual or technical reference manual for specific instructions and

warnings:

1. Write down the NI PCMCIA-4350 serial number for future reference.

2. Power off the computer.

Note If the computer and operating system support hot insertion, you can insert or remove

the NI PCMCIA-4350 at any time, even if the computer is powered on.

3. Remove the PCMCIA slot cover on the computer.

1 Portable Computer

2 PCMCIA Socket

3 NI PCMCIA-4350

Where to Start with the NI 435X 6 ni.com

4. Insert the 68-pin I/O connector of the NI PCMCIA-4350 into the

PCMCIA slot until the connector is firmly seated. The

NI PCMCIA-4350 connectors are keyed so the device can only be

inserted in one way.

The NI PCMCIA-4350 is now installed. Refer to the Configuring and

Testing the NI 435X section next.

♦NI USB-4350

Figure 2. NI USB-4350 with USB Cable

Note The NI USB-4350 is only supported in Windows 2000/XP/Me/98.

You can connect the NI USB-4350 to any available USB connector that

supports high-power, bus-powered peripheral devices. The following are

general installation instructions, but consult the PC user manual or

technical reference manual for specific instructions and warnings.

1. Connect the USB cable from the computer port or from any other hub,

to the port on the NI USB-4350.

2. The computer should immediately detect the NI USB-4350. When the

computer recognizes the NI USB-4350, the LED on the front panel

blinks or lights up, depending on the state of the device.

If the LED lights up after the NI USB-4350 is connected to the host,

the NI USB-4350 is functioning properly. If the LED remains off or

blinks, refer to Table 1.

1 NI USB-4350

2 Downstream USB Connector

3 Upstream USB Connector to PC

©National Instruments Corporation 7 Where to Start with the NI 435X

The NI USB-4350 is now installed. Refer to the Configuring and Testing

the NI 435X section next.

Table 1. LED Patterns for the NI USB-4350 States

LED NI USB-4350 State Description

On Configured state The NI USB-4350 is

configured.

Off Off or in the

low-power, suspend

mode

The NI USB-4350 is powered

off or in the low-power,

suspend mode.

1 blink Attached state The NI USB-4350 is

recognized, but not

configured.

2 blinks Addressed state The host computer detects the

NI USB-4350, but cannot

configure it because NI-DAQ

is improperly installed or

system resources are

unavailable. Check the

software installation.

3 blinks Power supply failure The internal power supply

shut down. Refer to the Power

Considerations for the

NI USB-4350 section in the

NI 435X User Manual for

more information.

4 blinks General error state Contact NI. Refer to the

Technical Support Resources

section for contact

information.

The LED blinks in one-second intervals during each cycle. The LED

then waits three seconds before repeating the cycle.

Where to Start with the NI 435X 8 ni.com

♦NI PXI-4351

Figure 3. NI PXI-4351 with PXI Chassis

You can install the NI PXI-4351 in any available 5 V peripheral slot in the

PXI or CompactPCI chassis.

Note The NI PXI-4351 does not have connections to reserved lines on the CompactPCI

J2 connector. Therefore, you can use the NI PXI-4351 in a CompactPCI system that uses

J2 connector lines for purposes other than PXI.

1. Write down the NI PXI-4351 serial number for future reference.

2. Plug in, but do not power on, the PXI or CompactPCI chassis.

Caution To protect both yourself and the computer from electrical hazards, do not power

on the computer until you finish installing the NI PXI-4351.

3. Choose an unused PXI or CompactPCI 5 V peripheral slot.

4. Remove the filler panel for the peripheral slot you selected.

5. Touch a metal part on the chassis to discharge any static electricity that

might be on your clothes or body.

Caution The NI PXI-4351 is ESD/contamination sensitive. Handle the device using the

metal bracket or edges.

1 PXI Chassis

2 NI PXI-4351

3 Ejector Handle in Down Position

ONSTANDBY

©National Instruments Corporation 9 Where to Start with the NI 435X

6. Insert the NI PXI-4351 into the selected 5 V slot. Use the

injector/ejector handle to fully insert the device.

7. Use the screw on the front panel of the NI PXI-4351 to fasten the

device to the front panel mounting rails of the PXI or CompactPCI

chassis.

8. Visually verify the installation.

9. Plug in and power on the PXI or CompactPCI chassis.

The NI PXI-4351 is now installed. Refer to the Configuring and Testing the

NI 435X section next.

♦NI PCI-4351

Figure 4. NI PCI-4351 with PC

You can install the NI PCI-4351 in any available PCI expansion slot in the

computer. However, to achieve the best noise performance, leave as much

room as possible between the NI PCI-4351 and other boards and hardware.

The following are general instructions, so consult the computer user

manual or technical reference manual for specific instructions and

warnings.

1. Write down the NI PCI-4351 serial number for future reference.

2. Plug in, but do not power on, the computer before installing the

NI PCI-4351 device. The power cord grounds the computer and

protects it from electrical damage while you are installing the module.

1PC

2 NI PCI-4351

3 PCI Expansion Slot

Where to Start with the NI 435X 10 ni.com

Caution To protect both yourself and the computer from electrical hazards, do not power

on the computer until you finish installing the NI PCI-4351.

3. Remove the top cover or access port to the PCI bus.

4. Select any available PCI expansion slot.

5. Locate the metal bracket that covers the cut-out in the back panel of the

chassis for the slot you selected. Remove and save the

bracket-retaining screw and the bracket cover.

6. Touch the metal part of the power supply case inside the computer to

discharge any static electricity that might be on your clothes or body.

Caution The NI PCI-4351 is ESD/contamination sensitive. Handle the device using the

metal bracket or edges.

7. Line up the NI PCI-4351 with the 68-pin connector near the cut-out on

the back panel. Using slow, evenly distributed pressure, press the

NI PCI-4351 straight down until it seats in the expansion slot.

8. Reinstall the bracket-retaining screw to secure the NI PCI-4351 to the

back panel rail.

9. Visually verify the installation.

10. Replace the computer cover and power on the computer.

The NI PCI-4351is now installed.Refertothe Configuring and Testing the

NI 435X section next.

Configuring and Testing the NI 435X

The NI 435Xis a completely software-configurable, Plug and Play device.

The Plug and Play services query the device and allocate the required

resources; then, the operating system enables the device for operation.

Complete the following steps to configure and test the NI 435X:

1. Launch Measurement & Automation Explorer (MAX) from the

computer.

Note You may want to first refresh <F5> in MAX.

2. Expand Devices and Interfaces.

3. Right-click the NI 435Xdevice and select Properties. In the System

window, note the Device Number that was assigned. Use this device

number when you program the device.

This manual suits for next models

Table of contents

Other National Instruments Measuring Instrument manuals

National Instruments

National Instruments NI Vision PCI-1409 User manual

National Instruments

National Instruments VirtualBench VB-8034 User manual

National Instruments

National Instruments VRTS User manual

National Instruments

National Instruments 779640-01 User manual

National Instruments

National Instruments PXIe-5622 User manual

National Instruments

National Instruments CMS-9024 User manual

National Instruments

National Instruments NI 5911 User manual

National Instruments

National Instruments NI PXIe-4138 Manual

National Instruments

National Instruments FD-11605 User manual

National Instruments

National Instruments NI PXIe-4143 Owner's manual

National Instruments

National Instruments NI PXI-562X User manual

National Instruments

National Instruments 9235 User manual

National Instruments

National Instruments RM-26999 Manual

National Instruments

National Instruments FD-11613 User manual

National Instruments

National Instruments NI PXI-5621 User manual

National Instruments

National Instruments NI 9213 User manual

National Instruments

National Instruments PXIe-5665 User manual

National Instruments

National Instruments NI PXI-562 Series User manual

National Instruments

National Instruments PXIe-5632 User manual

National Instruments

National Instruments TB-2725 User manual

National Instruments

National Instruments USB-5684 User manual

National Instruments

National Instruments 9775 User manual

National Instruments

National Instruments PXIe-5764 User manual

National Instruments

National Instruments PXIe-5668R User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual