National Instruments PXI-8195 User manual
-~
ARTISAN
®
~I
TECHNOLOGY
GROUP
Your definitive source
for
quality
pre-owned
equipment.
Artisan Technology
Group
Full-service,
independent
repair
center
with
experienced
engineers
and
technicians
on staff.
We
buy
your
excess,
underutilized,
and
idle
equipment
along
with
credit
for
buybacks
and
trade-ins
.
Custom
engineering
so
your
equipment
works
exactly as
you
specify.
•
Critical
and
expedited
services
•
Leasing
/
Rentals/
Demos
• In
stock/
Ready-to-ship
•
!TAR-certified
secure
asset
solutions
Expert
team
ITrust
guarantee
I
100%
satisfaction
All
tr
ademarks,
br
a
nd
names, a
nd
br
a
nd
s a
pp
earing here
in
are
th
e property of
th
e
ir
r
es
pecti
ve
ow
ner
s.
Find the National Instruments PXI-8196 at our website: Click HERE
INSTALLATION GUIDE
NI PXI-8195/8196
This document contains information about installing your
NI PXI-8195/8196 controller in a PXI chassis. For complete configuration
and troubleshooting information (including information about BIOS setup,
adding RAM, etc.), see the NI PXI-8195/8196 User Manual. The manual is
in PDF format on the recovery CD included with your controller and on the
National Instruments Web site, ni.com.
Installing the NI PXI-8195/8196
This section contains general installation instructions for the
NI PXI-8195/8196. Consult your PXI chassis user manual for specific
instructions and warnings.
1. Plug in your chassis before installing the NI PXI-8195/8196. The
power cord grounds the chassis and protects it from electrical damage
while you install the module. (Make sure the power switch is
turned off.)
Caution To protect both yourself and the chassis from electrical hazards, leave the chassis
off until you finish installing the NI PXI-8195/8196 module.
2. Remove any panels blocking access to the system controller slot
(Slot 1) in the chassis.
3. Touch the metal part of the case to discharge any static electricity that
might be on your clothes or body.
4. Remove the protective plastic covers from the four bracket-retaining
screws as shown in Figure 1.
5. Make sure the injector/ejector handle is in its downward position.
Align the NI PXI-8195/8196 with the card guides on the top and
bottom of the system controller slot.
NI PXI-8195/8196 Installation Guide 2 ni.com
Figure 1. Removing Protective Screw Caps
Caution Do not raise the injector/ejector handle as you insert the NI PXI-8195/8196. The
module will not insert properly unless the handle is in its downward position so that it does
not interfere with the injector rail on the chassis.
6. Hold the handle as you slowly slide the module into the chassis until
the handle catches on the injector/ejector rail.
7. Raise the injector/ejector handle until the module firmly seats into the
backplane receptacle connectors. The front panel of the
NI PXI-8195/8196 should be even with the front panel of the chassis.
8. Tighten the four bracket-retaining screws on the top and bottom of the
front panel to secure the NI PXI-8195/8196 to the chassis.
9. Check the installation.
10. Connect the keyboard and mouse to the USB connectors. If you are
using a PS/2 keyboard and a PS/2 mouse, use USB-to-PS/2 adapters to
connect both to the USB connectors on the front panel. You may use a
Y-splitter adapter to connect both keyboard and mouse to one USB
port, leaving the other USB port free for another peripheral, such as a
CD-ROM drive, or secondary hard drive. National Instruments offers
a Y-splitter adapter cable, Part Number 763608-01, available through
the online catalog at ni.com/products.
11. Connect the VGA monitor video cable to the VGA connector.
12. Connect devices to ports as required by your system configuration.
13. Power on the chassis.
14. Verify that the controller boots. If it does not boot, refer to the What If
the NI PXI-8195/8196 Does Not Boot? section later in this guide.
1 Protective Screw Cap (4X)
1
©National Instruments Corporation 3 NI PXI-8195/8196 Installation Guide
Figure 2 shows an NI PXI-8195/8196 controller installed in the system
controller slot of a National Instruments PXI-1042 chassis. You can place
PXI devices in any other slot.
Figure 2. NI 8195/8196 Installed in a PXI Chassis
How to Remove the Controller from the PXI Chassis
The NI PXI-8195/8196 controllers are designed for easy handling. To
remove the unit from the PXI chassis:
1. Turn off power.
2. Remove the bracket-retaining screws in the front panel.
3. Press the injector/ejector handle down.
4. Slide the unit out of the chassis.
What If the NI PXI-8195/8196 Does Not Boot?
Several problems can cause a controller not to boot. Here are some things
to look for and possible solutions.
Things to Notice
• Which LEDs come on? The Power OK LED should stay lit. The
Drive LED should blink during boot as the disk is accessed.
• What appears on the display? Does it hang at some particular point
(BIOS, Operating System, etc.)? If nothing appears on the screen, try
a different monitor. Does your monitor work with a different PC? If it
hangs, note the last screen output that you saw for reference when
consulting National Instruments technical support.
1 PXI-1042 Chassis 2 NI PXI-8195/8196
Controller
3 Injector/Ejector Rail
NI PXI-1042
2
3
1
National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation.
Refer to the Terms of Use section on ni.com/legal for more information about National
Instruments trademarks. Other product and company names mentioned herein are trademarks or trade
names of their respective companies. For patents covering National Instruments products, refer to the
appropriate location: Help»Patents in your software, the patents.txt file on your CD, or
ni.com/patents.
© 2005 National Instruments Corporation. All rights reserved. 371500A-01 Mar05
• What has changed about the system? Did you recently move the
system? Was there electrical storm activity? Did you recently add a
new module, memory chip, or piece of software?
Things to Try
• Make sure the chassis is plugged in to a working power source.
• Check any fuses or circuit breakers in the chassis or other power
supply (possibly a UPS).
• Make sure the controller module is firmly seated in the chassis.
• Remove all other modules from the chassis.
• Remove any nonessential cables or devices.
• Try the controller in a different chassis or a similar controller in this
same chassis.
• Recover the hard drive on the controller. (Refer to the Hard Drive
Recovery section of the NI PXI-8195/8196 User Manual.)
• Clear the CMOS. (Refer to the System CMOS section of the
NI PXI-8195/8196 User Manual.)
For more troubleshooting information, refer to the NI PXI-8195/8196 User
Manual. The manual is in PDF format on the recovery CD included with
your controller and on the National Instruments Web site, ni.com.
What If I Can’t See The Video?
This problem usually results from having the video card output set past the
limits of the monitor. You will need to boot Windows in Safe Mode. To do
this, reboot the controller. As Windows begins to boot, hold down <F8>.
You should now be able to reset the video driver to lower settings. Try
setting the resolution to 640 × 480 and the refresh rate to 60 Hz. Once you
reboot, you can raise these values again, using the test option in Windows.
These settings are accessible through the Advanced tab of the Display item
in the Control Panel. Alternately, you can try a different monitor,
preferably a newer and larger one.
If the system has been booted to Windows without a monitor attached, the
driver may have defaulted to the CRT connector being disabled. Press
<CTRL-ALT-F1> to re-enable the CRT in Windows.
Artisan
Technology
Group
is
an independent supplier
of
quality pre-owned equipment
Gold-standard
solutions
Extend the life
of
your
critical industrial,
commercial, and military systems
with
our
superior service and support.
We
buy
equipment
Planning to
upgrade
your current
equipment? Have surplus equipment taking
up shelf space? We'll give it a
new
home.
Learn
more!
Visit us at artisantg.com for more info
on price quotes, drivers, technical
specifications, manuals, and documentation.
Artisan Scientific
Corporation
dba
Artisan
Technology
Group
is
not
an affiliate,
representative,
or
authorized
distributor
for
any
manufacturer
listed herein.
We're here to make your life easier.
How
can
we
help you today?
(217)
352-9330
Isales@artisantg.com Iartisantg.com
Other manuals for PXI-8195
1
This manual suits for next models
1
Table of contents
Other National Instruments Controllers manuals
National Instruments
National Instruments GPIB-ENET User manual
National Instruments
National Instruments RMC-8354 User manual
National Instruments
National Instruments cRIO-9033 User manual
National Instruments
National Instruments RMC-8357 User manual
National Instruments
National Instruments NI PXI-8104 User manual
National Instruments
National Instruments PXI-8231 User manual
National Instruments
National Instruments PXI-7344 User manual
National Instruments
National Instruments NI cDAQ-9134 Owner's manual
National Instruments
National Instruments cRIO-9031 User manual
National Instruments
National Instruments GPIB PCI-GPIB User manual
National Instruments
National Instruments PXI-8820 User manual
National Instruments
National Instruments PXI-8186 User manual
National Instruments
National Instruments sbRIO-9860 User manual
National Instruments
National Instruments NI cRIO-9065 User manual
National Instruments
National Instruments PXIe-8106 User manual
National Instruments
National Instruments PXIe-8820 User manual
National Instruments
National Instruments cRIO-9023 User manual
National Instruments
National Instruments IC-3171 User manual
National Instruments
National Instruments IC-3173 User manual
National Instruments
National Instruments myRIO-1950 User manual
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
