National Instruments MyRIO-1950 User manual

myRIO-1950 JTAG Instructions

This document is intended to give instructions on how to use the myRIO-1950 JTAG port for

lead users. This is not intended for the general public and should be distributed with caution.

Using the JTAG port may cause permanent damage to the myRIO-1950 if improperly used.

1.0 General JTAG specifications

Logic Level: 1.8V1

Max JTAG Frequency: 10Mhz

Devices in JTAG Chain2:1st) Zynq PS (Arm processor)

2nd) Zynq PL (FPGA Fabric)

3rd) LCMXO2-640 CPLD2

Number of JTAG Instruction Registers:

Zynq PS = 4

Zynq PL = 6

CPLD = 8

1NOTE that the JTAG pins are ESD sensitive. Additionally they may be damaged if overvoltage

above 1.8V. Be sure to attach the VREF pin of the JTAG programmer properly. Do not force the

JTAG programmer to use any voltage other than 1.8V on its IO.

2CAUTION: The CPLD is not intended for customer access over JTAG. If you modify the CPLD your

myRIO-1950 will no longer function properly. Do not attempt to program the CPLD.

2.0 Physical Characteristics

When accessing JTAG on the myRIO-1950 be sure that header J5 is populated. If it is not then populate

this header with a through hole 2x3 0.1" spaced standard header. Note that Pin 1 is labeled with a 1 and

pin 6 is labeled with a 6.

Figure 1: JTAG Header Location

The following figure shows the JTAG header's pinnout.

Figure 2: Pinnout of JTAG header

3.0 General Instructions:

1) Attach the JTAG programmer to the JTAG header, connecting TDO to TDO, TCK to TCK, TDI to TDI,

TMS to TMS, GND to GND, and 1.8V to VREF.

2) Since this JTAG chain has multiple devices the JTAG software usually needs to know about all the

devices in the chain to operate properly. Many times the software just needs to know the instruction

Xilinx XMD software (IR stands for instruction register):

Figure 3: Example JTAG configuration

3) Configure the JTAG operating frequency to 10Mhz or slower.

4) After you configure these settings you should be able to communicate with any device in the JTAG

chain. DO NOT USE SOFTWARE TO RECONFIGURE THE CPLD, you WILL CAUSE THE BOARD TO NO

LONGER FUNCTION PROPERLY. This should not be a concern unless you are intentionally trying to

program the CPLD.

4.0 FPGA Pinnout and UCF File:

The following is a snapshot of a UCF file that defines the pinnout of the FPGA portion of the Zynq. Note

that some of these pins are a part of SPI ports and an I2C port that goes to the onboard Dacs, ADCs, and

accelerometer. These ports have timing requirements that are also included in this UCF snapshot.

##################################################################################

#Top Level Clock

NET "Clk40" LOC = K17 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #40Mhz clock, Input

#User IO

NET "aUserSwitch_n" LOC = F17 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #BUTTON0, Input

NET "cFpgaLed[0]" LOC = P16 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #LED0, output

NET "cFpgaLed[1]" LOC = P15 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #LED1, output

NET "cFpgaLed[2]" LOC = T19 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #LED2, output

NET "cFpgaLed[3]" LOC = R19 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #LED3, output

#Processor Reset

NET "system_reset_n" LOC = J15 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #output

#Accelerometer (MMA8452)

NET "aAccelScl" LOC = H17 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #output

NET "aAccelSda" LOC = K18 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aAccelInt_n" LOC = L17 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #output

#ADC (ADS7952)

NET "aAiSpiCs_n" LOC = F20 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #output

NET "aAiSpiClk" LOC = F19 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #output

NET "aAiSpiMosi" LOC = G18 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #output

NET "aAiSpiMiso" LOC = G17 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input

#DACs (DAC7562SDSC).

#There are 2 Dac devices selectable with the Cs[0] and Cs[1] pins.

#Note how this logic is inverted logic from a typical SPI port.

NET "aAoMxpSpiMosi_n" LOC = G20 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #output

NET "aAoMxpSpiClk_n" LOC = G19 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #output

NET "aAoMxpSpiCs[0]" LOC = G15 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #output

NET "aAoMxpSpiCs[1]" LOC = H15 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #output

NET "aAoMxpLdac" LOC = N16 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #output

#MXPA DIO

NET "aMxpAdio0" LOC = V12 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpAdio1" LOC = T10 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpAdio2" LOC = U12 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpAdio3" LOC = R14 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpAdio4" LOC = T12 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpAdio5" LOC = U18 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpAdio6" LOC = W13 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpAdio7" LOC = T15 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpAdio8" LOC = Y16 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpAdio9" LOC = P14 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpAdio10" LOC = P18 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpAdio11" LOC = T11 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpAdio12" LOC = T14 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpAdio13" LOC = N17 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpAdio14" LOC = V13 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpAdio15" LOC = W14 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aCom1Rx_n" LOC = Y17 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input

NET "aCom1Tx_n" LOC = Y14 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #output

#MXPB DIO

NET "aMxpBdio0" LOC = P20 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpBdio1" LOC = N20 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpBdio2" LOC = U20 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpBdio3" LOC = N18 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpBdio4" LOC = W20 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpBdio5" LOC = V20 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpBdio6" LOC = Y19 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpBdio7" LOC = Y18 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpBdio8" LOC = W16 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpBdio9" LOC = V16 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpBdio10" LOC = R17 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpBdio11" LOC = R16 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpBdio12" LOC = R18 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpBdio13" LOC = T17 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpBdio14" LOC = V18 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aMxpBdio15" LOC = V17 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input/output

NET "aCom2Rx_n" LOC = W19 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input

NET "aCom2Tx_n" LOC = W18 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #output

#Misc

NET "aDriveLow2" LOC = F16 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #output

NET "aDriveLow1" LOC = L16 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #output

NET "aDriveLow0" LOC = G14 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #output

NET "RESERVED0" LOC = H16 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW; #input

NET "RESERVED1" LOC = D20 | IOSTANDARD = LVCMOS33 | DRIVE = 8 | SLEW = SLOW;

##################################################################################

#Onboard Timing Parameters

#Analog Input Spi Timing

NET "aAiSpiMiso" OFFSET = IN 6 ns VALID 9 ns BEFORE "Clk40";

NET "aAiSpiClk" OFFSET = OUT 15 ns AFTER "Clk40";

NET "aAiSpiMosi" OFFSET = OUT 15 ns AFTER "Clk40";

NET "aAiSpiCs_n" OFFSET = OUT 15 ns AFTER "Clk40";

#Analog Output Spi Timing

NET "aAoMxpSpiCs[0]" OFFSET = OUT 20 ns AFTER "Clk40";

NET "aAoMxpSpiCs[1]" OFFSET = OUT 20 ns AFTER "Clk40";

NET "aAoMxpLdac" OFFSET = OUT 20 ns AFTER "Clk40";

NET "aAoMxpSpiClk_n" OFFSET = OUT 20 ns AFTER "Clk40";

NET "aAoMxpSpiMosi_n" OFFSET = OUT 20 ns AFTER "Clk40";

#Accelerometer I2c Timing

NET "aAccelSda" OFFSET = IN 5 ns VALID 10 ns BEFORE "Clk40";

NET "aAccelScl" OFFSET = OUT 20 ns AFTER "Clk40"; #Accelerometer I2c Parameter

NET "aAccelSda" OFFSET = OUT 20 ns AFTER "Clk40"; #Accelerometer I2c Parameter

##################################################################################

Special Pinnout instructions:

1) In your FPGA drive aDriveLow0, aDriveLow1, and aDriveLow3 to a '0'. These are used to control

some proprietary circuitry. If these are not driven low then the analog input's input impedance will be

different than specified in the myRIO user manual.

2) Configure RESERVED pins as inputs. DO NOT DRIVE THESE PINS YOU MAY DAMAGE YOUR BOARD

PERMENANTLY.

Other manuals for myRIO-1950

Table of contents

Other National Instruments Controllers manuals

National Instruments

National Instruments PCI-GPIB User manual

National Instruments

National Instruments CompactRIO cRIO-9072 User manual

National Instruments

National Instruments cRIO-9031 User manual

National Instruments

National Instruments RMC-8357 User manual

National Instruments

National Instruments RMC-8354 User manual

National Instruments

National Instruments PXI-8195 User manual

National Instruments

National Instruments NI PXIe-8840 User manual

National Instruments

National Instruments NI cRIO-9002 User manual

National Instruments

National Instruments NI PXI-8104 User manual

National Instruments

National Instruments NI SCXI 1357 User manual

National Instruments

National Instruments PXI-8820 User manual

National Instruments

National Instruments NI cDAQTM-9138 User manual

National Instruments

National Instruments GPIB-232CT-A IBCL EPROM User manual

National Instruments

National Instruments GPIB Series User manual

National Instruments

National Instruments PXI-8150B Quick start guide

National Instruments

National Instruments NI PXIe-8135 User manual

National Instruments

National Instruments NI 8352 User manual

National Instruments

National Instruments NI-7931 User manual

National Instruments

National Instruments PXI-7344 User manual

National Instruments

National Instruments GPIB GPIB-ENET/100 User manual

National Instruments

National Instruments sbRIO-9637 User manual

National Instruments

National Instruments NI cRIO-9022 User manual

National Instruments

National Instruments PCI-7330 User manual

National Instruments

National Instruments PXI-8186 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

National Instruments myRIO-1950 User manual

Popular Controllers manuals by other brands