NARGESA MX700 User manual
INSTRUCTIONS BOOK
PRADA NARGESA, S.L
Ctra. de Garrigàs a Sant Miquel s/n · 17476 Palau de Santa Eulàlia (Girona) SPAIN
Tel. +34 972568085 · [email protected] · www.nargesa.com
IRONWORKER MACHINE
MX700
Thank you for choosing our machines
www.nargesa.com
INDEX
FEATURES OF THE MACHINE ..............................................................................................
1.1. General dimensions ....................................................................................................
1.2. Description of the machine ..........................................................................................
1.3. Identification of the machne ........................................................................................
1.4. General characteristics ...............................................................................................
1.5. Description of safety devices ......................................................................................
2. TRANSPORT AND STORAGE ...............................................................................................
2.1. Transport .....................................................................................................................
2.2. Storage conditions ......................................................................................................
3. MAINTENANCE .......................................................................................................................
3.1. General maintenance ..................................................................................................
4. INSTALLMENT AND STARTING UP ......................................................................................
4.1. Location of the machine ..............................................................................................
4.2. Dimensions and working site ......................................................................................
4.3. Admissible outer conditions ........................................................................................
4.4. Connection to power supply ........................................................................................
5. OPERATION MANUAL ...........................................................................................................
5.1. Introduction .................................................................................................................
5.2. Feeding up of MX700 ..................................................................................................
5.3. Activation of the machine ............................................................................................
5.4. Working at manual mode ............................................................................................
5.5. Working at automatic mode ........................................................................................
5.6. Meter deletion .............................................................................................................
5.7. Desactivation of the machine ......................................................................................
5.8. Unusual performance situations ..................................................................................
6. WARNINGS .............................................................................................................................
7. ACCESSORIES .......................................................................................................................
TECHNICAL ANNEX
3
3
3
4
5
5
6
6
6
7
7
8
8
8
8
9
10
11
11
11
12
12
13
14
14
16
18
- 3 -
1. FEATURES OF THE MACHINE
1.1. General dimensions
1.2. Description of the machine
The MX700, has been especially designed for punching metal parts with different shapes depending on
the type of punch.
It may have other utilities by incorporating various accessories. It may be used for other purposes but
always following the manufacturer's guidelines, which provide all dockable accessories to the machine.
MX700 is made according to the European regulations for the manufacturing of
industrial machinery
Route
160mm
- 4 -
IRONWORKER MACHINE MX700
Displacement
Tension light
Information display
Operational keypad
Extractor
Support base for diez
Emergency stop
Pedal
1.3. Identification of the machine
Clamping point
General switch
Bench for dies
Box door
Ventilation grill
Electric engine
Electro-distributor
Safety valve
Hydraulic circuit container
Emptying cap
Oil filling cap
- 5 -
1.4. General characteristics
1.5. Description of safety devices
Protection devices of the MX700 are the extractor at the front of the machine to hold the material and avoid
putting your hands between the punch and the workpiece.
It also has a screen to prevent fragments projections, this display has a security system to prevent the
punch from descending if the screen is raised, only if the key to cancel safety is turned, then it coul be
possible to work with with the hazard light. Picture 2
Picture 1 Picture 2
Engine power 5,5 KW / 7,5 HP
Tension 230/400V Three-Phase
230V Single-Phase
Hydraulic power 70 Tn
Working speed 9 mm/s
Return speed 14 mm/s
Punch displacement 160 mm
Neck 350 mm
Tooling support table 600x350 mm
Dimensions 1150x1390x2080 mm
Weight 2000 Kg
- 6 -
IRONWORKER MACHINE MX700
2. TRANSPORT AND STORAGE
2.1. Transport
There are two ways of carrying out the transportation of the machine.
One of them is lifting it by its lower part using a forklifting truck as indicated in picture 3 and the other one
is by using a crane of forklifting truck as well and grabbing it by the clamping spot on the upper side, as
indicated in picture 4.
Picture 3 Picture 4
2.2. Storage conditions
The punch can never be stored in a place where it does not meet the following requirements:
* Humidity 30% to 95% non-condensing.
* Temperature -25 to 55 ° C or 75 ° C for periods not exceeding 24 hours (remember that these
temperatures are in storage)
* It is advisable not to stack heavy objects or machines.
* Do not disassemble for storage.
- 7 -
3. MAINTENANCE
3.1. General maintenance
Every 500 hours of use, check the oil level in the tank.
At the top of the tank is the oil plug. In case you need to add oil, fill to cover the peephole in the front of the
tank. (Picture 5)
- Replace every 2000 hours or every 5 years the hydraulic oil tank. Oil Type: CEPSA HYDRAULIC HM 68.
The tank has a capacity of 60 liters
Picture 5
WARNING:
Stop the machine and press the emergency stop to perform the oil change.
After replacing the oil, put up the machine and press the pedal in intermitencies increasing time pressure
gradually until the circuit fill up. Make sure the machine will perform normally.
- Lubricate punches periodically depending on use.
- If the use is daily and continuous, grease them every day.
- If the use is sporadic during the day then oil each week.
- If the use is sporadic, grease once a month.
Picture 6
1- Stop the machine
Oil filling cap
Oil level
Emptying cap
- 8 -
IRONWORKER MACHINE MX700
4. INSTALLMENT AND STARTING UP
4.1. Location of the machine
Efforts will be made to locate the machine properly to avoid having to move, otherwise the user must follow
the guidelines described in section transport (nº2). It should be placed on a flat, level surface to prevent
vibration and movement of the joint while performing. It is possible to fix the machine by bolts as is
provided with a lower base or foot with four holes as shown in Picture 7.
Picture 7
4.2. Dimensions and working site
When the machine is placed on site its dimensions, the workspace of the operator and the possible lengths
of the workpiece are to be taken into account.
The machine must be used by a single operator, which is to be placed frontally to the machine, never in a
lateral area because he has to control the whole machine and also main protections are designed to use
the front of it.
Picture 8
4.3. Admissible outer conditions
- Temperature betwee +5ºC and +40ºC without exceeding an average temperature of +35ºC during 24h
- Humidity between 30% and 90% with no water condensation.
- 9 -
4.4 Connection to power supply
IMPORTANT: This machine must be connected to a single outlet with earthing
The MX700 is equipped with a three phased engine 230V / 400V with 5,5Kw connected on a star shape to
connect into a power supply of 400V. It should be connected to an only power supply with the indicated
requirements. If the line tension is not the indicated one then there must be carried out a change of
connection of the motor bobins and the inverter as indicated in the following pictures:
Picture 9 Picture 10
In case of change of tension from 400V to 230V, change terminal 6 from 400V and put it in terminal 230V.
Picture 11
Star picture
(preset)
For tension 400V
Triangle picture
For tension 230V
Fuse of 0,5A
Fuse of 4A
Other manuals for MX700
1
Table of contents
Other NARGESA Industrial Equipment manuals
NARGESA
NARGESA NOA60 Owner's manual
NARGESA
NARGESA BM25 User manual
NARGESA
NARGESA PP200 User manual
NARGESA
NARGESA MX700 User manual
NARGESA
NARGESA NOA60 User manual
NARGESA
NARGESA PP200CNC User manual
NARGESA
NARGESA H3 User manual
NARGESA
NARGESA MT500 A User manual
NARGESA
NARGESA NF70 User manual
NARGESA
NARGESA H1 User manual
