Mitsubishi FX-10P-E Installation manual

OPERATION MANUAL

FX-10P-E

This manual explains the programming and monitoring

procedures of the micro PC MELSEC-FX series using the

FX-10P-E handy programming panel.

Read this manual carefully and thoroughly and make sure

the specifications for handy programming panel are correct.

See the corresponding FX series PC manual for details

about PC handing and instructions.

CONTENTS

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P1

2. Sample program operation . . . . . . . . . . . . . . . . . . P11

3. Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P21

4. Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P56

5. Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P65

6. Other functions . . . . . . . . . . . . . . . . . . . . . . . . . . . P75

7. Detailed procedure for starting up the system. . . . P89

8. Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P96

FX-10P-E Handy programming panel

Guidelines for the Safety of the User and Protection of the FX-10P-E HANDY

PROGRAMMING PANEL.

This manual provides information for the use of the FX-10P-E HANDY PROGRAMMING

PANEL. The manual has been written to be used by trained and competent personnel. The

definition of such a person or persons is as follows:

a) Any engineer who is responsible for the planning, design and construction of automatic

equipment using the product associated with this manual, should be of a competent

nature, trained and qualified to the local and national standards required to fulfill that

role. These engineers should be fully aware of all aspects of safety with regards to

automated equipment.

b) Any commissioning or service engineer must be of a competent nature, trained and

qualified to the local and national standards required to fulfill that job. These engineers

should also be trained in the use and maintenance of the completed product. This

includes being completely familiar with all associated documentation for said product. All

maintenance should be carried out in accordance with established safety practices.

c) All operators of the completed equipment (See Note) should be trained to use this

product in a safe manner in compliance to established safety practices. The operators

should also be familiar with documentation which is connected with the actual operation

of the completed equipment.

Note : The term ‘completed equipment’ refers to a third party constructed device which

contains or uses the product associated with this manual.

FX-10P-E Handy programming panel

Note’s on the Symbols Used in this Manual

At various times through out this manual certain symbols will be used to highlight points which

are intended to ensure the users personal safety and protect the integrity of equipment.

Whenever any of the following symbols are encountered its associated note must be read and

understood. Each of the symbols used will now be listed with a brief description of its meaning.

Hardware Warnings

1) Indicates that the identified danger WILL cause physical and property damage.

2) Indicates that the identified danger could POSSIBLY cause physical and property

damage.

3) Indicates a point of further interest or further explanation.

Software Warnings

4) Indicates special care must be taken when using this element of software.

5) Indicates a special point which the user of the associate software element should

be aware.

6) Indicates a point of interest or further explanation.

FX-10P-E Handy programming panel

iii

• Under no circumstances will Mitsubishi Electric be liable responsible for any consequential

damage that may arise as a result of the installation or use of this equipment.

• All examples and diagrams shown in this manual are intended only as an aid to

understanding the text, not to guarantee operation. Mitsubishi Electric will accept no

responsibility for actual use of the product based on these illustrative examples.

• Please contact a Mitsubishi distributor for more information concerning applications in life

critical situations or high reliability.

FX-10P-E Handy programming panel

Caution on operation

Thoroughly read the manual and sufficiently assure safety before executing the operation to

forcibly set devices to ON/OFF or the operation to change present values and set values of

word devices in the test mode.

Otherwise, the machine may be damaged and accidents may occur by erroneous operations.

Version upgrade to support FX1S, FX1N, FX2N and FX2NC Series Programmable controllers.

(ver 4.10 or later)

The FX-10P-E (ver 4.10 or later) fully supports all items and procedures used for the FX1S,

FX1N, FX2N and FX2NC PLCs.

Read section 1-3 in addition to the contents of the text when using the FX-10P-E (ver 4.10 or

later).

1. New Features

!: Already compatible ✕: Not yet compatible

Table 1.1

New Feature Supported by Peripheral

1 Addition of FX2N, FX1N, FX1S as selectable model !

2 Addition of basic and applied instructions !described in section 2 below

3 Expansion of device range !described in section 2 below

4Addition of 16K-step program memory !parameter setting

Setting of external RUN input !parameter setting

5 Writing of EPROM cassette ✕

6 Remote RUN/STOP function ✕

7 Specification of batteryless operation mode ✕

8 Setting communication Parameters ✕

9 Specification of modem initialization ✕

2. List of Additional Devices and Instructions

• For details of each instruction and devices, refer to the FX programming manual.

Table 2.1 Table 2.2

Devices Basic Instructions

Auxiliary relays M0 to M3071 3072 points LDP ORP

Data registers D0 to D7999 8000 points LDF ORF

Index registers V0 to V7, Z0 to Z7 16 points ANDP INV

ANDF

Table 2.3

Applied Instructions Applied Instructions Applied Instructions Applied Instructions

FNC No. Instruction FNC No. Instruction FNC No. Instruction FNC No. Instruction

59 PLSR 127 ESQR 158 DRVI 170 GRY

110 ECMP 129 INT 159 DRVA 171 GBIN

111 EZCP 130 SIN 160 TCMP 176 RD3A

118 EBCD 131 COS 161 TZCP 177 WR3A

119 EBIN 132 TAN 162 TADD 180 EXTR

120 EADD 147 SWAP 163 TSUB 224 to

246

In line

Compare

121 ESUB 155 DABS 166 TRD

122 EMUL 156 ZRN 167 TWR

123 EDIV 157 PLSV 169 HOUR

vii

3. New Operations for FX2N, FX2NC, FX1N, FX1S Support

3.1 Basic and Applied instructions are added

Symbol and input operation of additional basic instructions

Table 3.1

Instruction Description Mnemonic Key Operations

LDP Initial leading edge pulse contact LDP

LDF Initial trailing edge pulse contact LDF

ANDP Serial connection leading edge

pulse contact ANP

ANDF Serial connection trailing edge

pulse contact ANF

ORP Parallel connection leading edge

pulse contact ORP

ORF Parallel connection trailing edge

pulse contact ORF

INV Invert current logical status INV

LD P/I Device Number GO

LD FDevice Number GO

AND P/I Device Number GO

AND FDevice Number GO

OR P/I Device Number GO

OR FDevice Number GO

NOP P/I GO

viii

Applied instruction input operation

• It is the responsibility of the operator to ensure that the instruction entered is valid for the

current unit.

Application instruction input operation (by using the HELP function)

• When using the HELP function with a model other than FX2N be careful not to select an

invalid instruction.

FNC SPApplied Instruction No. Operand 1 SP Operand 2 GO

.....

The number of operands vary

depending on the instruction.

Example :

0 1

0 PROGRAM FLOW

1 TRANSFERS, COMP

10 CMP 12 MOV

11 ZCP 14 CML

Table of contents

Other Mitsubishi Controllers manuals

Mitsubishi

Mitsubishi MELSEC System Q User manual

Mitsubishi

Mitsubishi FX3G Series Owner's manual

Mitsubishi

Mitsubishi A Mounting instructions

Mitsubishi

Mitsubishi MELSEC-F FX1N-40MT-001 User manual

Mitsubishi

Mitsubishi FX0S Series User manual

Mitsubishi

Mitsubishi FX2N-32DP-IF User manual

Mitsubishi

Mitsubishi MELSEC Q Series User manual

Mitsubishi

Mitsubishi MELSEC User manual

Mitsubishi

Mitsubishi FX2N-64CL-M User manual

Mitsubishi

Mitsubishi MELSEC-Q EQ-V680D1 User manual

Mitsubishi

Mitsubishi MELSEC-L Series User manual

Mitsubishi

Mitsubishi QCPU (Q Mode) User manual

Mitsubishi

Mitsubishi MELSEC-AnS Series User manual

Mitsubishi

Mitsubishi FX2N-2LC User manual

Mitsubishi

Mitsubishi FX2N-10GM User manual

Mitsubishi

Mitsubishi CR760-Q User manual

Mitsubishi

Mitsubishi FX3U-2HSY-ADP User manual

Mitsubishi

Mitsubishi MELFA SQ Series User manual

Mitsubishi

Mitsubishi Q68TD-G-H01 User manual

Mitsubishi

Mitsubishi Q64TD User manual

Mitsubishi

Mitsubishi q64rd User manual

Mitsubishi

Mitsubishi AL2-2TC-ADP User manual

Mitsubishi

Mitsubishi FX2N-232IF User manual

Mitsubishi

Mitsubishi MELSEC-F FX3U-4AD User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual