MiTAC PH10FEU User manual
MITAC Desktop Board PH10FEU
Desktop Board Features
This chapter briefly describes the
features
of
Desktop Board
PH10FEU.
Feature Summary
Form Factor
Micro-ATX (244 millimeters [9.6 inches] x 244 millimeters [9.6 inches])
Processor
8th generation Intel® Core processor family with up to 95 W TDP in an LGA1151
socket
Main Memory
Support Dual channel DDR4
Support for up to 64 GB of system memory
288-pin DDR4 u-DIMM
4
Chipset
Intel® Q370 Platform Controller Hub (PCH)
Integrated
Graphics
Intel® HD Graphics (By CPU)
External Graphics
External graphics support provided through the PCIe 3.0 x16 bus slot
Audio
RealTek* ALC892 audio codec for 7.1 channel High Definition Audio
Front panel microphone/headphone header with support for HD Audio
Legacy I/O
Legacy I/O Controller (Nuvoton* NCT6683D) that provides:
Hardware management support
Expansion
Capabilities
PCIe 3.0 x16 (Black)
1
PCIe 3.0 x8 (Black) with x4 lanes
1
PCIe 3.0 x8 (Black) with x4 lanes
1
M.2 M key 2280, 2242
1
External I/O
USB 3.1 Gen2 port
4
USB2.0 port
2
Display Port
2
DVI-D
1
RJ-45
2
6-stack Audio Jack (with S/PDIF)
1
Internal I/O
USB 2.0 port
2
USB 3.0 port
2
Desktop front panel header
1
Audio Header (Front Panel Mic-in/Hp-out)
1
Universal ATX Power Connector: 2x12
1
12V CPU ATX Power Connector: 4x2
1
Serial Port port (RS232)
4
CPU FAN header (4-pin)
1
SYS FAN header (4-pin)
3
SATA Connector
6
2x8 pin TPM header
1
Hardware Monitor
Subsystem
Hardware monitoring through the Nuvoton* NCT6683D legacy I/O controller,
including:
Remote thermal sensor
4-pin system fan header
LAN Support
Intel® I219 Gigabit (10/100/1000 Mb/s) LAN
Intel® I210 Gigabit (10/100/1000 Mb/s) LAN
BIOS
AMI UEFI BIOS Support for Advanced Configuration and Power Interface (ACPI)
Instantly Available PC
Technology
Support for PCI Express Revision 3.0
Wake on LAN
Power Requirement
ATX
Environment
Operating Temperature: 0 °C to +55 °C
Storage Temperature: -40°C to +70°C
Safety
CE
FCC
Table . MiTAC Desktop Board PH10FEU Components (Shown in the Figure)
A
Back Panel Connectors
B
Sys Fan header
C
ATX Power Connector 8P
D
LGA 1151 CPU Socket
E
CPU FAN header
F
DDR4 DIMM
G
Sys Fan header
H
ATX Power Connector 24P
I
COM Port
J
Sys Fan header
K
SATA 2 (SATA-DOM)
L
TPM header
M
SATA 0 (SATA-DOM)
N
SATA
O
Front Panel Header (Power Button/ Reset Button / HDD Active LED/ Power
ON LED)
P
USB2.0 header
Q
USB3.0 header
R
M.2 M key 2242/2280
S
Front Audio header
T
PCIE 3.0 Slot x8
U
PCIE 3.0 Slot x8
V
PCIE 3.0 Slot x16
Processor
The board supports 8th generation Intel Core processors. Other processors may be
supported in the future. This board supports processors with a maximum wattage of
95 W Thermal Design Power (TDP).
NOTE
This board has specific requirements for providing power to the processor. Additional
power required will depend on configurations chosen by the integrator.
System Memory
NOTE
To be fully compliant with all applicable DDR SDRAM memory specifications, the board
should be populated with DIMMs that support the Serial Presence Detect (SPD) data
structure. This allows the BIOS to read the SPD data and program the chipset to
accurately configure memory settings for optimum performance. If non-SPD memory
is installed, the BIOS will attempt to correctly configure the memory settings, but
performance and reliability may be impacted or the DIMMs may not function under the
determined frequency.
The Desktop Board has
four
288-pin DDR4 u-DIMM sockets with gold-plated contacts.
These sockets support:
Serial
Presence Detect (SPD) memory
only
Non-ECC memory
Up to 64 GB
of
memory
MITAC Desktop Board PH10SU
Hardware Specifiction
Header Definition
CPU FAN/ SYS FAN: 4-pin CPU Fan Connector(location B, E, G, J)
Pin
1
2
3
4
Signal
GND
VCC12
FAN_TACH
PWM
Use this header to connect the cooling fan to your motherboard to keep the system stable and
reliable.
Note: A 4-pin fan is required for fan support 4pin Control
Front Panel Header(location O)
Signal
Pin
Pin
Signal
SATA_LED_PWR
1
2
GRN_BLNK_HRD
SATA_LED_D_N
3
4
YLW_BLNK_HRD
GND
5
6
PWRBT_N_R
FP_RST_R_N
7
8
GND
FP PWR
9
10
SATA Connectors
7
1
Name
TYPE
S1
GND
S2
TXP
S3
TXN
S4
GND
S5
RXN
S6
RXP
S7
GND
Connects to the Serial ATA ready drives via the Serial ATA cable.
SATA DOM Connectors (Location K, M)
7
1
Name
TYPE
S1
GND
S2
TXP
S3
TXN
S4
GND
S5
RXN
S6
RXP
S7
P5V
Connects to the Serial ATA ready drives via the Serial ATA cable.
Internal Serial Port Header Pin-out (Location I)
Signal
Pin
Pin
Signal
SPA_DCD
1
2
SPA_DSR
SPA_SIN_N
3
4
SPA_RTS
SPA_OUT_N
5
6
SPA_CTS
SPA_DTR
7
8
SPA_RI
GND
9
TPM Header(Location L)
Signal
Pin
Pin
Signal
P3V3
1
2
FRAME_N
LAD0
3
4
KEY
LAD1
5
6
PLT_RST_N
LAD2
7
8
GND
Table of contents
Other MiTAC Motherboard manuals
MiTAC
MiTAC Tyan S5542 User manual
MiTAC
MiTAC 6513VX Service manual
MiTAC
MiTAC 6010Eu/va Service manual
MiTAC
MiTAC Tyan S5542 User manual
MiTAC
MiTAC TYAN S5565 User manual
MiTAC
MiTAC PD10BI User manual
MiTAC
MiTAC TYAN S5539 User manual
MiTAC
MiTAC 6515WU User manual
MiTAC
MiTAC 8575 User manual
MiTAC
MiTAC PH14ADI User manual
MiTAC
MiTAC PD10AI User manual
MiTAC
MiTAC PD11KS User manual
MiTAC
MiTAC MSC-1610 User manual
MiTAC
MiTAC TYAN S7010 User manual
MiTAC
MiTAC TYAN S5552 User manual
MiTAC
MiTAC PH10LU User manual
MiTAC
MiTAC TYAN S8030 User manual
MiTAC
MiTAC PD10TI User manual
MiTAC
MiTAC TYAN S5502 User manual
MiTAC
MiTAC TYAN S7103 User manual
