Milwaukee PH55 User manual

BATTERY REPLACEMENT:

Units are supplied with BEPS (Battery Error Pre-venting

System) which avoids any erroneous reading due to low

battery level, by switching the meter off. To replace the

batteries unscrew the battery compartment cap and replace all

three 1.5V batteries while paying attention to their polarity.

Make sure the gasket is in place before screwing back the cap.

Batteries should only be replaced in a nonhazardous area using

the battery type specified in this instruction manual.

WARRANTY:

This meter (base unit) is warranted from all defects in

materials and manufacturing for a period of two years.

The electrode (probe end) is warranted for a period of 6

months.

During this period, the required repair or replacement of parts,

where the damage is not due to negligence or erroneous

operation by the user, will be effected free of charge.

WARRANTY REGISTRATION:

Please go to our web site and register your unit at

http://www.milwaukeeinstruments.com/registration.html

__________________________________________________

FOR A MUCH MORE DETAILED

OPERATORS MANUAL

GO TO OUR WEB SITE / MANUALS SECTION

AT THE FOLLOWING ADDRESS

www.milwaukeeinstruments.com

_______________________________________

Milwaukee Instruments

2950 Business Park Drive

Rocky Mount, NC 27804

Phone # 242-443-3630

PH55 & PH56 WATERPROOF

METER

STARTER MANUAL

•When calibration is completed the unit LED will flash

“OK 2”for 2 sec. then return to the temperature display

& normal operation taking the unit out of the calibration

mode. ** YOU ARE NOW CALIBRATED AND

READY TO PERFORM MEASURMENTS

_____________________________________

#3: OPERATION OF THE PH55 –PH56:

• Remove the unit from your storage container cup or jar

( Remember to always store the probe wet )

• Turn the pH55 - Ph56 on by pressing the ON key.

• Immerse the electrode in the solution to be tested.

• Stir gently and wait for the reading to stabilize.

• After the reading is stable you can press “SET / HOLD”

button and unit will freeze display until you press the

“SET / HOLD” button again to release the display.

• After use, turn unit off by pressing the OFF key and

rinse the end of the probe with water and then return it

to jar or cup for storage.

____________________________________________

#3: STORAGE OF THE PH55 –PH56:

Leave the protective cap off and put the unit back in a

cup or jar that has 1” to 1.5” of either bottle drinking

water, or 4.01 calibration solution, or MA9015 storage

solution

___________________________________________

You Must Move Unit - VERY FAST –Between

The 7.0 & 4.0 Cal Solution During The

Calibration Procedure –> Please Read Through

Instructions prior to starting procedure

NEVER LET YOUR PROBE DRY OUT

_________________________________

NEVER USE DISTILLED OR

DEIONIZED WATER FOR STORAGE

PURPOSES.

Other manuals for PH55

This manual suits for next models

Table of contents

Other Milwaukee Measuring Instrument manuals

Milwaukee

Milwaukee 2235-20 User manual

Milwaukee

Milwaukee MW500 User manual

Milwaukee

Milwaukee PH55 User manual

Milwaukee

Milwaukee SM101 User manual

Milwaukee

Milwaukee CD97 User manual

Milwaukee

Milwaukee pH54 User manual

Milwaukee

Milwaukee MW190 MAX User manual

Milwaukee

Milwaukee MW12 User manual

Milwaukee

Milwaukee MI405 User manual

Milwaukee

Milwaukee MI407 User manual

Milwaukee

Milwaukee MI405 User manual

Milwaukee

Milwaukee Mi 190 User manual

Milwaukee

Milwaukee MW102 User manual

Milwaukee

Milwaukee M12 ICAV3 User manual

Milwaukee

Milwaukee EC40 User manual

Milwaukee

Milwaukee MW306 MAX User manual

Milwaukee

Milwaukee MW105 MAX User manual

Milwaukee

Milwaukee M12 CLLP-301C User manual

Milwaukee

Milwaukee C12 CMH User manual

Milwaukee

Milwaukee SM500 User manual

Milwaukee

Milwaukee SMS510 User manual

Milwaukee

Milwaukee MI455 User manual

Milwaukee

Milwaukee MR32ATC User manual

Milwaukee

Milwaukee M12 CLLP User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual